How do I configure a 1422 board so that Ext Trig 0 is directed to Control 0 in LVDS format to drive the line rate for a Dalsa camera?

I need to take an encoder in TTL format into trigger line 0 and redirect it to output control line 0 so that the board drives it in LVDS format. This will become the External Sync line for the Dalsa CL-P1-2048 line scan camera. I assume this is done in the icd file, but the documentation on this subject and the 1422 itself is extremely poor.

Brian,
I do not believe you are going to do exactly what you are looking for since there is no way to write to the control lines programatically or from the camera file. If you are looking to use this signal to trigger each line, you may want to take a look at this example:
http://zone.ni.com/devzone/explprog.nsf/6c163603265406328625682a006ed37d/f2799dc12a94be2586256a79006985ce?OpenDocument
It uses motion and routes the encoder signal across for the line trigger. You can modify this so the input trigger is from your trigger line. I hope this information helps.
Chris D
NI Applications Engineer

Similar Messages

How to enable Fullfillment set menu in the Right click at the line level for a responsibility?, by default it comes for OM ADMIN.

How to enable Fullfillment set menu in the Right click at the line level for a responsibility?, by default it comes for OM ADMIN.
for this responsibility i need to have teh sets enabled. how to do teh same.
similar to OM ADMIN as shown below:
Kindly advice on teh steps. i believe its some menu /function inclusion can you pl share teh pointer.
regards,
bala

AFAIK then there is no way to do that system wide. You can only do that via userChrome.css or an extension like the Menu Editor per profile .You can install extensions globally, but the user will have to enable them anyway. That is not required for userChrome.css code.

How do I uninstall CS2 on a PC when it does not appear in control panel add or remove programs, the hard drive was replaced and the program corrupted.

how do I uninstall CS2 on a PC when it does not appear in control panel add or remove programs, the hard drive was replaced and the program corrupted.

reinstall over your current installation and then uninstall, Error: Activation Server Unavailable | CS2, Acrobat 7, Audition 3
or uninstall manually, Manually remove Adobe Creative Suite 2.x | Windows

I'm trying to record in Adobe Audition and it keeps saying my the sample rates for my input and output devices do not match. How do I correct this?

I'm trying to record in Audition and it keeps saying my sample rates for the input and output devices don't match. How do I fix this?

I finally have communication between the ISA One and Audition. I moved the optic cable to another SPDIF on the computer and from the SPDIF to ADAT on the ISA One and it finally agreed that the communication was at the same clock speed. The audio was not intelligible so I moved the optic cable back to the original configuration and I can record voice that is clean.

How do I delete photos from my ipad that have been imported directly from a memory card.

I have searched loads of forums and they all talk about using itunes to delete photos, but this seems to only apply to photos that orginated from a PC. The photos I am trying to delete were loaded directly on to my ipad from a memory card and don't appear in itunes. I know I can delete photos individually on my ipad but I have hundreds of them, The only option I have found that comes close to what I want to do is back-up ipad, delete photos I don't want to restore (not sure where to find back up or how to delete), rebuild ipad and restore - this seems a long winded way of doing something that would take less than a minute in windows. I have an ipad1 and am running windows 7 on a standards Windows PC.
Many Thanks in anticipation that someone will be able to help me
Regards
Keith

Photos copied to the iPad via the camera connection kit (and those taken with the iPad or saved from emails/websites etc) should appear in Windows Explorer on a PC so you should be able to delete them from there - those types of photos should make the iPad appear as a camera to your computer. You should also be able to delete them at the end of the photo import process via, for example, the camera wizard.

How to include Business Place field in the line item for argentinian comp?

Dear,
We've just implemented a company code from Argentina, but when we try to post a document, the system doesn't show the field Business place in the line item, so we can't fill this field. This problem is causing some posting errors for us. Is the any way to set this field in the transaction FB01?
We have already checked the field status for account and posting key. The field is not available is this functions.
Thanks in advance,
Leandro Albertini

Hi Albertini,
Follow the path as follows and configure the business place for your plant and company code:
SPRO, Financial Accounting, Financial Accounting Global Settings, Tax on Sales/Purchases, Basic Settings, Settings for Tax on Sales/Purchases in South Korea, Assign Business Place.
In this activity, you can assign a business place to a plant. The business place is recorded for each posting.
Please reward points if helpful.
Regards,
Sreekanth....

How do I change the bit rate for dls?? How times can I download one song??

I'm new to iTunes. I already downloaded 3 songs when I realized that the default bit rate is 128Kbps. I tried changing the bit rate to 192Kbps with a (Variable Bit Rate) checked.....unfortunately when I downloaded the next 2 songs the bit rate turned out to be the same.
Do I have to restart Windows or iTunes before downloading again?
And now that I have 5 songs with a lower br than I wanted... in order for me to have(download) the song at the higher bit rate...Is it possible to download one song more than once?
Thanx.

You have no choice as to bit rate when purchasing from the iTunes Music Store. The official bit rate of all tracks there is 128 kbps (a very few have been reported to be at higher rates, but that's not a choice you can make, it's how the track was encoded by the record company). The setting in the iTunes Importing preference is for tracks you import from CDs only and has no effect on iTMS purchases.
Is it possible to download one song more than once?
No. Except in extraordinary circumstances, the iTMS allows only one download per purchase.
Forum Tip: Since you're new here, you've probably not discovered the Search feature available on every Discussions page, but next time, it might save you time (and everyone else from having to answer the same question multiple times) if you search a couple of ways for a topic before you post a question.
Regards.

I need use the line data(basler spl2048 camera,NI1433 board) to perform FFT transform ,how can i use transformed data to construct an image

hello everyone! as what i haved mentioned in the title.In optical coherence tomography system ,i need to perform for every line data whick accquired by NI1433,how can i use
the transformed data tto construct an depth image .

This is no longer my main area of expertise, but here is results of brief search:
Spectral Domain Optical Coherence Tomography System Design: sensitivity fall-off and processing speed enhancement
look at Chapter 5
https://circle.ubc.ca/bitstream/id/91474/ubc_2010_fall_chan_kenny.pdf
Ultrahigh-resolution, high-speed, Fourier
domain optical coherence tomography and
methods for dispersion compensation
http://www.opticsinfobase.org/oe/abstract.cfm?uri=OE-12-11-2404
hope this helps,
Curt
Curt Corum, Ph.D.
Center for Magnetic Resonance Research
University of Minnesota

How can i configure firefox, in a way that is fits in my monitor screen?

When I'am using firefox, I only see a part of the screen. Every new screen I have to zoom to an size that the screen fits. This happend after a new installation. Is the a way in which I can make the screen fit automaticly?

Were you using either of these add-ons that let you set a default zoom level for all sites? If so, check to see whether it was disabled during the upgrade. Or if this is a completely new installation, you might want to grab the add-on again.
*[https://addons.mozilla.org/en-US/firefox/addon/2592/ NoSquint]
*[https://addons.mozilla.org/en-US/firefox/addon/6965/ Default FullZoom Level]

How to get all the line items for each Purchasing Document ?

Hi,
There are multiple purchase orders (EBELN) in PSA with different line items (EBELP). But, when loaded into ODS from PSA, I am getting purcahse orders with only one Line item.
Eg.,If the EBELN has a Record# 4000005 and has 3 line items in it (10,20, 30), I am receiving 10 or 20 or 30 Line item.
As there are more than one line item per PO, how can I retreive all of them?
Also, there are no conditions / routines in transfer structure and update rules.
Please let me know

problem solved.
I moved the EBELP field from Data fields to Key Fields in ODS.

How do I reduce the bit rate for existing songs

Some of the songs are too large. How can I reduce the file size of selected songs? Thanks.

Hi,
You can do it by converting your file either with a lower bit rate or using an another compression algorithm. Be aware taugh that by doing so, you will loss audio quality. The best way is to restart, if possible, from your original files with your new importing settings.
To change your importing settings, go in the iTunes preferences, in the Advanced tab and then in the Importing tab and set the compressing algortihm and bit rate. AAC encoder is the algorith that will gives you the better compressing ratio.
Then, you you can either chose to reimport from your original CD (iTunes will ask you to replace the previously imported files) or select from the advanced menu the converting selection.

How to know the sampling rate for NI6624?

Dears,
I am trying to measure a transient signal that is a time-vary counter train. The target frequency is increased from 0 Hz to 50 Hz when the measurement time rises to 1 s from 0 s. The NI 6624 card and the LabVIEW DAQmx have been adopted. In the block diagram, the terminal of measurement method “Low Frequency with 1 Counter” is set in “DAQmx Create Channel (CI-Frequency).vi”, and the “Finite Samples” mode is chosen in “DAQmx Timing (Implicit).vi”. Then the transient signal points (increasing-frequency points) will be got successfully within 1 s. Now I have a question: how do I estimate the time step “dt” between these data points? Knowing the default sampling rate of the card seems a better way to help me to define the "dt", and calculates the time stamp at each data point. If the foregoing concept is true, how the internal sampling rate in NI6624 obtains? Beside, for the transient counter signal, any way to get the time stamp of data points is also welcome.
Thanks for anyone comment,
Adan

Adan,
When selecting "Implicit" as the DAQmx Timing type, you are indicating
that a data point will be taken for every measurement the counter
performs. When you create a task of type "Low Frequency with 1
Counter," the counter simply uses the card's internal timebase to
measure the period between edges of your signal. It then takes this
period measurement and converts it to a frequency. Therefore, the
spacing between the samples you read out is simply the inverse of the
subsequent frequency measurement sample.
Hope this helps,
Ryan Verret
Product Marketing Engineer
Signal Generators
National Instruments

How to find the device number for the line input for sound measurements

Hi,
I would like to measure the input of sound wave given to a line input of a PC. Can anyone tell me how to write a DLL Program to actualy get the device numbers. Appreciate your help.
Thank You,
Mudda.

Hello Mudda,
Are you connecting a microphone to the sound card of your PC? I assume
that you want to use the built-in LabVIEW Sound VIs, and would like to write a
LabVIEW DLL which returns the device numbers of the sound devices.
If you are using a Windows system, you will have to use some Windows API
functions to get that information.
Microsoft (and their website) can help with the specific functions which
enumerate the sound devices (with documents like this:
http://msdn.microsoft.com/library/default.asp?url=/library/en-us/multimed/htm/_win32_devices_and_data_types.asp).
Your LabVIEW DLL will then be a wrapper for a Windows call.
I am happy to help out in any way I can. Feel free to post again with a
little more information on what exactly you wish to do, or with any other
follow up questions. Thanks for posting!
Regards,
Travis M
LabVIEW R&D
National Instruments

How to format hard drive with mac air for use on mac and pc

I'm new to MAC and can't make much sence of what has been said to do in other questions. All I want to be able to do is use my 500gb My Passport hard drive on my MAC and other PC's. I have saved all the data that I want to keep on another hard drive so can re-format the hard drive if needed. I want to do all the set up on my MAC AIR.
Please help,
Cheers Hutch

Reading assignment:
http://en.wikipedia.org/wiki/ExFAT
Ciao.

HT3702 So how do I get rid of a charge that was made in an app with no app store authorization from the itunes account holder.

I'm having a problem with a credit card purchase I made through logmein trial version. Granted I'll pay for it now, but the phone should have asked if I would authorize the purchase. So I feel that apple owes me for the mistake and pay up. As manager of the Secret Service in the United States of America I demand better help than that. It's either pay the bill or I will take the sum of One (1) billion dollars right out of their account and give it to the poor after I pay my bill off. They have until October 1, 2012 to respond or it will happen and they will lose that billion permanently. This is a threat against them and I would not take it lightly. You people have been WARNED.
Sincerely,
Jamie.
Manager Head of the Secret Service.
Tel # 1-920-645-9425

I forgot to mention I already deleted angry birds off of my app after transfering purchases from my iphone.

How do I configure a 1422 board so that Ext Trig 0 is directed to Control 0 in LVDS format to drive the line rate for a Dalsa camera?

Similar Messages

Maybe you are looking for