How do I Configure, G5 Tiger, MBox and BX5a to output sound???

Can't get sound in or out. Please help! Downloaded standalone core audio driver from digidesign site, G5 then recognized mBox on USB port, but speaker sounds super fuzzy.

Nate;
All VIs used to do pattern I/O on 653x boards handle ports only. If you need to change just one line of that port, you will need to keep the other bits of that port as 0s and just change the bit correspondent to that particular line you need to change.
Hope this helps.
Filipe Altoe
Applications Engineer
National Instruments

Similar Messages

How do I configure DW to open and load a file?

I have DreamWeaver CS5 running on a Mac. Whenever I double-click to open a DreamWeaver compatible file (such as an HTML file), if DW is not already open, DW launches but does not load the file. Once DW is launced, I can double-click the file and it will load. How do I configure DW to open and load a file together?
DW: v11 b 4993
OS X: 10.7.4 (11E53)

HTML files are normally configured to open in a browser. The default on a Mac is to open the file in Safari.
You can right-click the filename in the Mac Finder, and select Open With > Dreamweaver CS5 from the context menu.
Alternatively, select an HTML file in Mac Finder, and press Cmd+I to open the Info panel. In the Open With section, select Dreamweaver CS5 as the default program, and click the Change All button.

How do you configure AME CS5.5 to overwrite existing output files?

How do you configure AME CS5.5 to overwrite existing output files? So far the only options I have found are to increment the output file name or fail. From the explaination of file increment I would have expected overwrite to be the alternative. We work daily with the same file(s) on an hourly basis and convert via watch folder to over a dozen file types and network mapped destinations. Re-using the same file name is critical to the final project (updating website content). Does anyone have any suggestions?

Has there been any updates on overwriting output files in CS6? This would be extremely helpful.

How do you configure the default Webserver and AppEX in XE(windows)?

I'm new to XE but an old hat with Oracle Standard and Enterprise editions, Apache and AppEx (htmldb).
What is the default webserver that comes with XE(windows) and how do you configure it? Where are the httpd config files?
Also I read in the doco that you need to use Apache if you want to use https. Is there any doco on how to configure XE with Apache?
Also with respect to AppEx
where are the physcial files e.g. I can't find the following file or directories. Where is virtual directory /i/ mapped to? Where is this configured?
http://127.0.0.1:8080/i/htmldb/builder/db_users_ctrl.gif
regards
Paul Platt

Paul,
for the Apex files see: http://daust.blogspot.com/2006/03/where-are-images-of-application.html
For configuring the Apache as a proxy to XE:
HTTPS with Oracle XE ?
Re: Existing http server
~Dietmar.

How do I configure the brightness, contrast and colour settings of the built-in HD Camera on iMac?

I have recently purchased an iMac after making the switch from PC.
I am struggling to find an app, or settings configuration where I can modify the brightness, contrast, color and white balance settings for the built-in HD camera. The online manuals didnt give me any answers so I thought I would turn to the communities pages for some help.
The room where the iMac is situated has a light behind me and I am facing the wall so not much light in front of me except the ambient light from the screen. Friends on FaceTime, Skype etc. say that the picture from the built-in camera is too dark and difficult to make out my face clearly. How can I fix this?
Any and all help is most welcome.
Thanks
UKRichard

I would move it if it weren't the main room light that is fixed to the ceiling. Not remodelling my house just for the iMac camera. On my old PC all the webcams came with utilities to adjust these settings, I am surprised Apple dont have something similar for free.
I did see another post about iGlasses here, but not sure I want to pay $10 just to adjust my camera settings
Message was edited by: ukrichard

How do I configure a VPN Site and Subnets in Lync when clients have /32 Addresses?

Hello,
I've found a few people asking this question out in the "interwebs" but no one seems to quite answer their question (Those poor souls).
In most occasions that I've seen, my customers have configured their VPN networks with a /24 (255.255.255.0) ip address. However, when those clients connect to the VPN they are actually getting a /32 (255.255.255.255) address.
This seems to pose an issue for Lync reporting when it comes to configuring a VPN site and VPN subnets.
(NOTE:You might ask why these customers are not going about best practice and using split-tunneling? In this case, they absolutely CANNOT institute split-tunneling so all traffic MUST flow through the VPN tunnel.)
For example sake, here is how I would imagine to setup a VPN site with subnets in Lync Network Configuration:
VPN (Site)
    -172.16.33.0 /24 (Subnet)
    -172.16.34.0 /24 (Subnet)
    -172.16.35.0 /24 (Subnet)
The problem is that when I run a Location Report in Lync to look at call data to/from the VPN site, it's not there. Reason being, the VPN client was given a /32 address which doesn't match up to the /24 I configured in Lync.
So, in my mind my options are:
Create a /32 subnet for each single address corresponding to a VPN client and attach them to the VPN site (What a mess).
Change the subnet mask for the 3 subnets I've defined to /32 instead of /24 and see what happens even though putting an IP address of 172.16.33.0 /32 doesn't make much sense.
Remove the subnets and site from Lync because CAC and Bandwidth control are actually useless over VPN.
Any thoughts on this?
John K. Boslooper | Lync Technical Specialist | Project Leadership Associates
Phone: 312.448.2269 | www.projectleadership.net

Jin,
/32 addresses are a valid subnet mask, however that means that a host with a IP Address of 192.168.23.4 and a subnet mask of 255.255.255.255 (/32) is the ONLY host on that subnet.
The VPN configuration is correct. The /32 mask is common with a Juniper VPN (which is what they are using) and the DHCP server that is handing out the addresses is the Juniper VPN appliance.
They have already started working out a plan to use a different internal DHCP relay which should hand out the addresses correctly.
There has to be someone else out there with this issue or that can point out that i'm overlooking one key principal with VPN subnets.
Anyone?
John K. Boslooper | Lync Technical Specialist | Project Leadership Associates Phone: 312.448.2269 | www.projectleadership.net

How can I configure NI PCI 6221 and DAQ SCB-68 for pressure sensors?

Hello
everybody,
I am using the measuring board (NI PCI 6221) and DAQ
SCB-68 for the data acquisition.
With the DAQ-Assistant I created AI for the voltage of
pressure sensors. In a big indicator panel from this DAQ-Assistant I see the
voltage for both sensors in the correct size. But if I set sensors in the
blockdiagramm to control the signals for sensor one I get a wrong voltage size
and for sensor 2 nothing.
How can I configure this data acquisition equipment to
get the correct signals?
Thanks a lot for your help.

I do not know the type of sensor you are using. But pressure transducers may have a very low output voltage(in the mVolt range). They also need an excitation voltage. Here is an introduction. http://focus.ti.com.cn/cn/lit/an/sloa034/sloa034.pdfThen working with pressure sensors I always use 3 stages in the circuit.
1 Instrumentation Amplifier as a preamp
2 filterstage
3 Final amp and output buffer
(you may combine stage 2 and 3)
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

How can i configure Distributed cache servers and front-end servers for Streamlined topology in share point 2013??

my question is regarding SharePoint 2013 Farm topology. if i want go with Streamlined topology and having (2 distribute cache and Rm servers+ 2 front-end servers+ 2 batch-processing servers+ cluster sql server) then how distributed servers will
be connecting to front end servers? Can i use windows 2012 NLB feature? if i use NLB and then do i need to install NLB to all distributed servers and front-end servers and split-out services? What will be the configuration regarding my scenario.
Thanks in Advanced!

For the Distributed Cache servers, you simply make them farm members (like any other SharePoint servers) and turn on the Distributed Cache service (while making sure it is disabled on all other farm members). Then, validate no other services (except for
the Foundation Web service due to ease of solution management) is enabled on the DC servers and no end user requests or crawl requests are being routed to the DC servers. You do not need/use NLB for DC.
Trevor Seward
Follow or contact me at...
&nbsp&nbsp
This post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

Adding second 5508 Wireless Controller, how to best configure for load balancing and redundancy?

We recently purchased a second 5508 wireless controller (both licensed for 100+ AP's). What is the easiest way to configure and add the second controller so I can split the load between the 2 controllers and provide failover capability? I do not want to run in an active/standby mode since that will effectively cut our AP capacity by half even with both controllers running.
Should I just manually configure the new controller (long and drawn out process to configure all the parameters), backup the current controller configuration and import to the second controller (then change the ip address) or is their an easier way to cause the two controllers to synchronize the configurations?
We are currently running 7.0.240.0 on our active controller and I would rather not upgrade it until we get the new controller online so I can have less downtime and fail AP's between controllers.
What can you recommend?
Jim

I'm assuming then, when I update the software on the controllers I won't be able to choose which controller is primary for an AP anymore and will lose access to the 100 AP licenses (and the capability to have 100 AP's registered, 100 licenses on each Controller).
Read the Deployment Guide. It should mention that you can choose which controller is the "primary" and which one is the "secondary".
If I'm not concerned about quick failover can I still assign a primary and secondary controller for each AP and utilize all 200 AP licenses that are split between the 2 controllers?
You sure can. But this "old school" method is a very expensive method. Why? Because this means that you have two controllers with similar AP licenses. The newer AP SSO means one controller has a full license and the other has only an HA SSO license, which is a lot cheaper.

I'd like to Know how can I configure a Lookout process and Zetron 1730 and Zetron 1732

I'd like to configure a Lookout proccess with a Zetron 1730 controller and a 1732 RTU.When I configure an I/O of the Digital Module(connected to the 1732) as an Output and another one as an input,when I excite the output from the Lookout process it also excites the input in the screen.If I do the same configuration separately (just with a 1730 and a Digital module)it works OK!

Iteco,
I am familiar with using Zetron with Lookout. But I'm have a hard time understanding exactly what the problem is.
There is a good Zetron Demo that NI has for Lookout, It can be found here.
http://zone.ni.com/devzone/explprog.nsf/6c163603265406328625682a006ed37d/fe8bac9d3fbb69ac86256ae100563b9a?OpenDocument
Hope this helps.
Oliver Scheurer
Aegis Solutions, Inc.
2660-T Yonkers Road
Raleigh, NC 27604
Phone: (919) 861-0103 Ext. 231
Fax: (919) 861-0104
www.aegis-solutions.com

How can I set the file name and folder for output to PDF from another application?

I am developing an application in Microsoft Access where the printed reports are to be saved in PDF format for archive purposes. I can send the output to Adobe X, but the default file name is the Access report name and the folder selected is the one last used.
What I need to do is to create the file with a specific name (which changes for each run) and to a specific folder (which also changes for each run).
The language I'm using is Visual Basic for Applications which is located in an Access form that controls the report production.
Any suggestions, please?

Got it - many thanks.

How to fix streaming audio pops/crackles and then stops all sound

I am a google Chrome user. I am unsure if this problem is related to Chrome or to Flash by I suspect there is a problem with both. I previously had this problem where when you start a youtube video for example the audio would pop/crack and then the audio would go dead. If you were able to put the video on full screen before this happened it would work fine. This really only happens with windowed (non-fullscreen videos). Previously I went in to my chrome plugins and disabled chrome's native flash and that fixed the issue. With the most recent update to Chrome this has happened again. This time disabling chrome's flash does not work. On the adobe version site it says that for chrome the version should be 11.5.31.137 but it shows me as using 11.5.502.146. The latter would be the version for firefox. I do not use firefox. Could this be causing my trouble? I have used the official flash uninstaller and restarted my computer and reinstalled but the same thing happened. Thanks.

Thanks for the link. I have tried what they recommend. I currently have two flash files. I have disabled the chrome one and the one that is enabled is C:\Windows\system32\Macromed\Flash\NPSWF32_11_5_502_146.dll
However, I ran the chrome://flash and this is what I got:
Flash plugin
11,5,502,146 C:\Windows\system32\Macromed\Flash\NPSWF32_11_5_502_146.dll (not used)
--- Crash data ---
Crash Reporting
Enable crash reporting to see crash IDs
For more details
https://support.google.com/chrome/?p=ui_usagestat
--- GPU information ---
Graphics card
ATI Radeon HD 4800 Series
Driver display name
aticfx32.dll,aticfx32.dll,aticfx32.dll,atiumdag.dll,atidxx32.dll,atiumdva.cap
Graphics card
ATI Radeon HD 4800 Series
Driver display name
aticfx32.dll,aticfx32.dll,aticfx32.dll,atiumdag.dll,atidxx32.dll,atiumdva.cap
--- GPU driver, more information ---
Vendor Id
0x1002
Device Id
0x9460
Driver vendor
Advanced Micro Devices, Inc.
Driver version
8.970.100.3000
Driver date
7-3-2012
Pixel shader version
3.0
Vertex shader version
3.0
GL version
GL_VENDOR
GL_RENDERER
GL_VERSION
GL_EXTENSIONS
I've never looked at this before but it is weird that it is saying that that flash is not used.
Anyone know about the firefox version of flash installing for Chrome because as I described above that doesn't seem right.

How can I share a Tiger server's User database to a Panther server?

I need some help to set this up. Keep in mind I do not have a DNS server.
I have a Tiger server with Xserve and an older Panther server, both on the same local network. I have a whole bunch of users setup on the Tiger server. The Panther server does not have any users setup on it. I do not want to have to type in all the users all over again in the Panther server. What I'd like to be able to do is somehow share and syncronize the user database on the Tiger server with the Panther server.
I looked into the Open Directory settings but I do not understand what to do. How do I configure the Tiger and Panther servers respectively so the Panther server can sync with the Tiger server's users database. Is this possible? It seems like it with Open Directory, one being the Open Directory Master and the other being the Open Directory Replica? But I just don't understand how to set this up. Also the Panther OD settings seem quite different than Tiger's in Open Directory.
Any help would be appreciated.
Message was edited by: robocub1

Hi
It may be best to set up your 10.4 Server as an Open Directory Master first and then use Directory Access on your 10.3 Server to connect to the Tiger Server so as it can use the same User Database. This should be possible. OD Master/Replica relationships are not possible if the OS versions are different, even if the Master was 10.4.11 and the Replica was 10.4.10. You have no chance when its 10.4 and 10.3.
http://images.apple.com/server/macosx/docs/OpenDirectory_Adminv10.5.pdf
The link is for 10.5 but the basics are the same. This is a recent post that describes how to set up an OD Master:
http://discussions.apple.com/thread.jspa?threadID=1377046&tstart=0
I'm guessing that your 10.4 Server is Standalone and is serving simple file services only (AFP and possibly SMB/Windows). If this is the case (and I can't see how it can't be) then your users will be in the local NetInfo node. This will be the default node that is presented to you in WorkGroup Manager. You always get a warning that your are working in an invisible node (if you have not disabled this) when working in the Server's local node. Don't worry there is nothing wrong with the warning. WorkGroup Manager on Panther (10.3) Server works the same way.
You could if you wanted to simply export the Users and Groups from WGM in 10.4 and import them into WGM on 10.3. This should save you having to key them all in again. If the prospect of configuring internal DNS Services and all that goes with it seems to much for you then this is probably the simplest option. How do you do this? Launch WGM (its the same for both versions), select the Server Menu and select Export after first selecting desired users. Do the same for Groups. Use the same procedure in reverse. The Users and Groups files are not very big and can easily be transferred using a memory stick etc.
There are differences between the two versions which are mostly to do with Server Admin. In 10.4 Server there are more services. One of the Services will be Open Directory. In 10.4 Open Directory will only show a green light by the side of the service if it is in any role other than Standalone. Server Admin on 10.3 Server will always show the green light by the side of the Open Directory Service. This does not mean that it is an OD Master, you have to click on Settings and inspect the Role to see what it actually is.
You should be able to connect to a 10.3 Server with 10.4's Admin tools but don't be tempted to use Server Admin to configure/change anything on the 10.3 Server. You should not be able to go the other way 10.3 > 10.4 using the same tools.
Internal DNS Services are a requirement for LDAP Services (and pretty much everything else) on Servers generally, although for simple file services not absolutely necessary. Internal DNS Services do not have to be configured on the Server itself just as long as they are configured on another server, for example, on the same network. If these are the only two servers on the network then you will have to configure DNS Services on either one or both of them depending on what you want.
Not available on your 10.3 Server but is on your 10.4 Server are Access Control Lists (ACLs). This is a permissions model that is in addition to the standard POSIX permissions. Think carefully about how you provide permissions to your network clients if there is a mix of client OS, 10.3, 10.4 etc.
Hope this helps, Tony

How to do configuration the Essbase server with shared services

We install Hyperion 11.1.2, we install Hyperion Essbase server and planning on UNIX box (64-bit) and FR Report, Essbase administration services and foundation services on windows 2008 (64-bit) server.
When I am doing the configuration on windows server it’s not asking anywhere Essbase server details.
How to do configuration with Essbase server and planning where these are on Unix box and foundation services are on windows server.
Help me !
Thanks
Dharm

I did the install as PTH0RC and my inventory.xml is configured correctly, but I get the following message trying to run a simple view
C:\Oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\resources\instance>epmsys_registry view
com.hyperion.hit.registry.exceptions.RegistryException: reg.properties not configured.
at com.hyperion.hit.registry.Registry.getInstance(Registry.java:338)
at com.hyperion.hit.registry.regedit.RegEditUtility.main(RegEditUtility.java:101)
An error occured during the operation. Detailed Message is - reg.properties notconfigured.

HT1288 Configuring VPN on iPhone and iPad

How do I configure VPN in iPhone and iPad - I see the answers but they are as clear as mud! I need a "small" step-by-step guide, ie small steps, in order to fully understand please.

go to settings-general-vpn-add vnp configuration-select the type of vpn you're using by touching one of the types across the top. From there fill out the information provided by your vpn and click save. then just turn it on from settings-vpn-on/off toggle.

How do I Configure, G5 Tiger, MBox and BX5a to output sound???

Similar Messages

Maybe you are looking for