How do I connect Airport Extreme in place of Buffalo wireless router in Japan?

How do I connect Airport Extreme to replace current Buffalo wireless router? ISP is StarCat in Japan.

Hello DM1960,
Thanks for using Apple Support Communities.
To set up and configure your AirPort Extreme please follow the steps in the article below:
OS X Mavericks: Set up an Apple wireless device
http://support.apple.com/kb/PH14058
Take care,
Alex H.

Similar Messages

How do I connect airport extreme to seagate hard drive using windows

How do I connect airport extreme to seagate hard drive using windows?

First the AirPort Extreme Base Station (AEBS) cannot share out an external HDD attached to its USB port unless it is formatted in either HFS+ or FAT16/32. It will not work if the HDD is formatted in either NTFS or ExFAT.
If the HDD is formatted properly, when you access the AEBS with the AirPort Utility, does the HDD show up properly on the Disks tab of the utility?
If it does, then you would access the HDD as any other network share, using the following format: //servername/sharename. In the case of the AirPort Disk (a HDD attached to the USB port of either an Extreme or Time Capsule), the "servername" would be the Extreme's Base Station Name, and the "sharename" would be the volumename of the HDD.

How do I connect Airport Extreme to XBox 360 live

I just bought an Airport Extreme to use as my wireless router. Everything connected beautifully EXCEPT my all in one HP Printer and my XBOX 360. If I manually enter the settings, I can connect but only for a minute or 2. Once my son starts using xbox LIVE, the connection gets dropped. All instructions I can find must be for older utilities. I eventually plugged in my old G Router into an open LAN port on the back of the Airport Extreme and got my printer working when connecting to the old network ID but still can't get XBOX 360 to connect and stay connected. Any help is appreciated.

Ok, thanks for the update. Do you have the Xbox connected to the 802.11n AirPort Extreme Base Station (AEBSn) by Ethernet (wire) or by wireless? If wireless, temporarily connect it by Ethernet to verify that you can get connectivity via this method.
If you were using wireless, which of the following is the wireless adapter that you are using?
802.11g or
802.11n?

How do I use Airport Extreme to act as a wireless receiver for a Mac Pro?

Hello -
I'm trying to use an Airport Extreme (1st Generation) as a wireless receiver for a Mac Pro but I can't figure out how. My main modem / wireless router (non-Apple) is upstairs. My Mac Pro is down stairs. I'm looking to get internet connection for that Mac Pro downstairs. Is it possible to use the Airport Extreme to connect the Mac Pro to the wireless internet provided by my wireless router?
Thanks for the help.
Nathan

Is it possible to use the Airport Extreme to connect the Mac Pro to the wireless internet provided by my wireless router?
Unfortunately, Apple designed their routers to work with other Apple routers. It would be extremely unilikely that the AirPort Exteme could be configured to work with a router from another manufacturer.
The AirPort Extreme would need to be configured to "Extend a wireless network", but an error message is almost surely to occur when you try this.
There are other alternatives, but they would involve more hardware. Post back if you are interested.

How do i install airport extreme on a windows pc and route it to another windows desktop?

How do I install airport extreme into a windows desktop pc and then successfully route it to another windows desktop?

The AirPort Extreme Base Station (AEBS) is an Internet router that supports both wired and wireless network clients. You can connect both of your desktop, using either media, to the AEBS for network connectivity.

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

How can I connect airport extremes using a wired-switch connection and have roaming capability?

My goal is to have 2 airport extremes and 1 timecapule connected via an ethernet switch so that I can enable roaming. I have no problems connecting them wirelessly where I create the wireless network on a primary airport wireless then add the others "extending" the network. However, if I attempt to do the same thing with a wired connection everything stops working (no connections from any airport). Here's the topology I'm trying to achieve. I believe my problem relates to the switch and the fact that I am serving up DHCP from a separate server. Is there a way I can achieve this (or similar) type of configuration? Thanks in advance.
BTW, I have read the various documents on the roaming network topology but none seem to be a match to this.

To answer your question, yes, if I _only_ have the main "create wireless network" airport connected/wired to the switch, everything works correctly.
OK, got that.
Also, if I have each of the 3 airports/timecapsule "create wireless network" using the same ssid name and passwd/protocol, everything works correctly (but of course, no roaming under this scenario
Sorry, you have me confused on this one. When the AirPorts are all configured to "create a wireless network", use the same SSID, security and password, and all AirPorts are in Bridge Mode........that is the exact definition of a "roaming" network.
Not sure what you mean when you say "no roaming" in this configuration.
Also, if I have the main "create wireless network" configured and have the 2 other airports "extend the network" and _not_ have them connected via the ethernet cable, everything works correctly (wireless airport interconnection)
That is correct.
However, if I plug the 2 other "extend the network" airports into the switch via ethernet, all connectivity shuts down.
This is not a correct setup. The "extend" setting on the AirPort assumes that they will connect using wireless. If you then try to connect an Ethernet cable to an AirPort that is expecting a wireless connection, that will result in a big feedback loop and effectively crash the network.

How do you connect Airport Extreme and share HP Photosmart 3210 Printer?

Hello,
I have a Mac and PC Network composed of:
iMac 24'' Leopard 10.5.2 (main computer)
2 PC Fujitsu Pentium 4 on Windows XP
2 PC HP Pentium 4 on Windows XP
my network/connections are done via Airport Extreme and 2 hubs (other devices connected to the network like Wii, XBox etc.)
I am trying to share my HP Photosmart 3210 using the USB connector on Airport Extreme but I am experiencing strange problems while printing from the iMac. I can print an e-mail or a "light" document however if I want to print a Mac powerpoint (Mac office) largest document, the problem starts after the second or 3rd page, the printer goes on pause at the middle of the page and the interface indicates "problem communicating with the printer" or something like that.....unique possibility is to turn the printer off and start again but the problem persists. However, it seems that the printer works ok from the PC's.
I have tried to install the latest versin of the HP driver on my iMac but while configuring, the printer doesn't appear....I have checked on the printer settings and the IP address is 0.0.0.0.
I am now thinking about connecting the Printer via one of the Ethernet port on Airport Extreme.
Questions:
1. Any help on the above ? Any advice ?
2. Is it normal to have no IP address on the printer when connected via USB on Airport Extreme ?
3. Why HP config doesn't recognize the printer on the network ?
4. Why does it work from the PCs and not from the iMac and why does it print light documents and not big ones ? Is this a memory7buffer problem on the printer ? What can I do if this is the case ?
5. On the Airport Extreme Utility, do I need to share the printer via "Bonjour"?
6. I am willing to plug an extrenal HD on the Airport Express USB port. Is it possible to put first a multi USB port on the Airport Extreme USB or is it going to cause problems ?
Thanks a lot for your help.
P.
Message was edited by: vador300
Message was edited by: vador300
Message was edited by: vador300
Message was edited by: vador300

NCBob, Welcome to the discussion area!
If I understand correctly you are replacing the Linksys. It should be a simple replacement. Connect the cable modem to the WAN port on the AirPort Extreme base station (AEBS). Connect your Ethernet devices (including the switch) to the AEBS LAN ports.

How do I connect Airport Extreme to U-verse Internet Gateway: Motorola Model NVG510

I tried to set up a new network with the Airport Extreme and get no Internet connectivity from the AT&T gateway. The Extreme network sets up fine and I can access it from all my devices, but no Internet.
What am I doing wrong?
Thanks,
Mick Jones

It will only take a minute to check the Ethernet cable. Just connect it from a LAN <-> port on the Uverse gateway to the Ethernet port on a computer. Turn off the wireless on the computer and see if you can get a good Internet connection that way.
If you can, great. You cannot, then you either have a bad Ethernet cable or the port on the gateway may not be working correctly.
Power up the AirPort Extreme for a few minutes
Then, hold in the reset button on the AirPort Extreme for 10-12 seconds and release
Allow a full minute for the AirPort to restart
Connect the Ethernet cable from a LAN <-> port on the Uverse gateway to the WAN "O" port on the AirPort Extreme
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on Other WiFi Devices
Click AirPort Extreme
The utility will open up automatically, take a minute to analyze things, then suggest that the AirPort will be configured to create a new network. The window will look like the example below, except that you will see an AirPort Extreme instead of an AirPort Express.
Network Name......type in a short, simple name that you want to call your wireless network
Base Station Name.....type in a short, simple name that you want to use to identify the AirPort Extreme
Password......type in a password that will be used for both the Base Station and Wireless Network
Verify the password
Click Next
You should have a green light on the AirPort Extreme in a minute or two, and you should be able to log on to the new network and get an Internet connection.

How to get an Airport Extreme to work behind a wired Router????!!!!!!

Hey all major issue I am at my inlaws and they have a cable modem going into wired linksys router in their basement where the cable comes in and then distributing out through the house ethernet to key areas. Recently they have gotten wireless laptops and want to setup their airport extreme off of one of these ports so they can sit out on their deck and use the net.
I tried the auto-configuration and get no internet connectivity, occasionally it comes through at like 4 k/s(using the WAN port, the Lan port gives no connection like it should). If I plug directly into the same port I get 8MB down and 1MB up, so I am confident its not the ethernet coming to the location.
Additionally, if i take the extreme downstairs and run it form the cable modem and do the autosetup it works beautifully as well.
So obviously the autosetup isnt working for the Airport running behind the router why? I have tried to muss with the settings, run it in bridge mode and such but to no avail.
Any advice on how to do this? The base is updated to its latest firmware 5.7.

I have been using an AEBS connected to one port of my D-Link Router for years. 2 months ago I have upgraded to OS 10.5 and have had no problems with having wireless computers connecting. I just decided to change my Security to WPA and after the Airport Utility (V.5.3.2) did the settings UPDATE, I haven't been able to connect via WIFI. I had all WIFI IP address be in the 10.0.1.1 range, and now I have tried everything I can think of to get it to work like I did but no luck.
I should mention that my router is set for static IP because of webcasting and other requirements.
I have searched and asked and can't solve the problem.
Mike

AirPort Extreme 802.11n as a wireless router and local network switch?

Good afternoon,
I'm curious if its possible to have the APE in wireless network mode and connect systems via hard line as well?
I have an AirPort Extreme 802.11n set to "Create a Wireless Network" mode that is attached directly to a cable modem for internet connectevity. My issue is that while all wireless devices (several iPods, two iPhones and three laptop computers) connect to the APE without issue (and have internet access), when I try to plug in a Windows 7 desktop computer via one of the ethernet jacks, Windows is unable to connect and shows the network as "unidentified," spitting back a private IP address as opposed to a local LAN (this behavior repeats for an Ubuntu Linux box as well).
Not sure if the APE is misconfigured, this is a Windows 7 issue or if its improper use on my part (though this also precludes me from connecting a gigabit switch to the APE).
Thank you,
Nathan

Properly configured, the AirPort should provide both wired and wireless network client with Internet access.
At this point, I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Can I use an Airport Extreme as a modem and wireless router?

I realize this shows my ignorance, but I am wondering if I need to lease my isp's (Comcast) modem or if I can use and Airport Extreme instead. Thanks for your help.

AirPort Extreme is a router only.....no modem on board.....so you will need a modem to work with the AirPort Extreme if you want to be able to access the Internet.

Connect AirPort Extreme Base Station to air card

How do you connect AirPort Extreme Base Station to Verizon Air Card?

Sorry, but the Air Card cannot be used with the USB port on the AirPort Extreme because that port will only work with a hard drive and/or a printer.
Suggest that you check with Verizon to see if they have an adapter or wireless router for the Air Card that will provide an Ethernet signal to the AirPort Extreme.

Cable needed to connect airport extreme?

How do I connect airport extreme to older speakers which are connected to older receiver amp? Do I need USB to radio jack? Have Itunes on IMAC , os 10.4.11. I know I need to update os sy to 10.5. I have new Iphone. I want to use remote app to send music to speakers.

There is not an audio port on the AirPort Extreme, so it cannot be used to stream audio per your question.
An AirPort Express will do the job.

Can I use non-apple notebook to connect AirPort Extreme?

I
Can I use non-apple notebook to connect AirPort Extreme?

He might be trying to do so to promote his products or may be there was some misunderstanding.
Airport Extreme will work as a wireless router supporting upto 50 systems including Mac computers, PCs, iPad, iPhone, iPod touch, Apple TV and virtually all 802.11a/b/g/n Wi-Fi wireless devices — all at the same time.
for reference http://store.apple.com/us/product/MD031LL/A/AirPort-Extreme

How do I connect Airport Extreme in place of Buffalo wireless router in Japan?

Similar Messages

Maybe you are looking for