How do I connect computers to same network?

I cannot figure out why my IMac and Macbook will not connect with each other so I can download files to my Macbook that was wiped out and is like a new computer.  I'm trying to share files and internet and I'm unsure how to confirm that my computers are connected to the same network...what do I need to be sure to check?  Thank you to anyone who understands this and can help!

Hi..
Help here >  3 Easy Ways to Share Files Between Macs

Similar Messages

  • Deskjet Ink Adv. 6525 Invisible to all devices even if connected to the same network

    Okey, So a few days ago I got a  new router (new Wifi network). When I connected my printer to it, none of my Apple or Android devices couldn't find my printer, even if they could before I got my new router. I called my new network the same way as my previouse one, and used the same password,but my devices still can't find it.They're all connected to the same network, and no errors are shown on the printer, or on the Wireless network test results. I tryed everything I could find from the FAQs on this site, but I still can't solve the problem.The printer prints and scans normally when it's connected to my computer. Please answer if you have any ideas how to solve my problem!
    Best regards, Marko

    Hi Marko,
    Welcome to the HP Support forums.  I understand that since changing your router your mobile devices can’t find your printer and you can only print from your computer with the cable connected. 
    Please run the Wireless Setup Wizard from the front panel of the printer.  Even though you have used the same network name and password, the new router broadcasts different information that the old router.  So please run the wireless setup wizard from the front panel of the printer.  The instructions on how to do this can be found in your User Guide on page 31 in the section titled “To connect the product with the Wireless Setup Wizard”.
    For your computer it sounds like the step to switch the connection from a USB connection to a wireless connection was accidentally missed during the setup.  The instructions on how to make that switch can also be found in your User Guide on page 33in the section titled “Change from a USB connection to a wireless network”. Windows and Mac each have their own sub-section.
    For your mobile devices please turn the wi-fi setting off on it.  Please wait approximately 15 seconds to allow the device to truly disconnect from the network.  Please turn the wi-fi setting back on and then choose your network.  It’s possible that the devices still “thought” they were connected to your old network as the name didn’t change.
    Regards,
    Happytohelp01
    Please click on the Thumbs Up on the right to say “Thanks” for helping!
    Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
    I work on behalf of HP

  • When I connect my ipad to a wifi network, the iphone connects to the same network

    When I connect my iOS 8 iPad 4 to the guest network at work, my iOS 8 iPhone 5s automatically connects to the same network. When I disconnect the iPhone so I can send an email from my iCloud account (which is blocked on the work network) and tell it to forget the network, it disconnects my iPad too. Each time I tell the iPhone to forget the network, when I reconnect my iPad, the iPhone connects again.
    How do I tell my iPhone to never connect to the work guest network while allowing my iPad to connect?
    I do not like this feature in iOS 8.

    Unfortunately, this does not help me, there are no issues with the operation of the WiFi, it is operating normally on both devices.
    The issue is that in iOS 8, the WiFi network information is shared across linked devices. Therefore, if I add a network to one device, it is added to the other device and if I forget a network on one device, it is forgotten on the other.
    I want to use a network on one device (the iPad) and to not use the network on the other (iPhone). How do I tell the iPhone to not connect to the WiFi without disabling WiFi while allowing the iPad to connect to the network? It is annoying to have to disable the iPhone WiFi manually each day when I get to work and it is prone to forgetting to turn it back on when I leave.

  • HT202213 How do I connect computers on home sharing?

    How do I connect computers on home sharing?
    Im not sure what to do on this new version of Itunes.

    On one computer in itunes from the top menu
    File > Home Sharing > Create Home Share  Enter your apple id and create share
    On the second computer
    again File > Home Sharing> Create Home Share  Use exactly the same apple id as the
    first machine
    On each machine to get the itunes 10 look and feel
    View > ShowSidebar
    Also Authorise each Machine with the other apple id Store > Authorise this computer
    You should now have an orange house icon in the Shared section of your itunes

  • I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

    I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

    It says that my DHCP has to be changed! How? to what?
    It is 802.11g.express. but is set to default by the computer (Macbook Air).
    The other is 802.11n. (express)
    Extreme is 802.11.g. Is the Main Airport.
    It is on ethernet & wep 128 security.

  • I can't print wirelessly from my iMac although it is connected to the same network as the printer and I can print fine from my iPad to the same network

    I have downloaded and installed the driver from the HP website for the HP Envy 5530. While I can send documents from my iMac to the printer using a USB cable, it will not print wirelessly. When I tried to install the wireless connection, I got the dialogue box saying "Devise not reachable" and it suggested I check whether the iMac is connected to the wireless network (it is and the signal strength is excellent, Safari runs well) and that I check the printer is connected to the same network (it is). I am able to print items from my iPad wirelessly using the network so I don't understand why the iMac won't recognise the printer wirelessly when everything else works fine.

    From the Safari menu bar, select
              Safari ▹ Preferences... ▹ Advanced
    and check the box marked
              Include Bonjour in the Bookmarks menu
    if it's not already checked. Then select
              Bookmarks ▹ Bonjour ▹ Name of printer
    A web page served by the printer should open. Does it?

  • HT5706 I just purchased an AppleTV and am trying to connect AirPlay with my mac (2012 model) In 'system preferences displays' an airplay menu is listed but it says 'no device detected'. My AppleTV and macbook are connected to the same network. Any help?

    I just purchased an AppleTV and am trying to connect AirPlay with my mac (2012 model) In 'system preferences > displays' an airplay menu is listed but it says 'no device detected'. My AppleTV and macbook are connected to the same network. Any suggestions why it is not working?

    Troubleshoot the network as that is likely what is causing the issue.
    Also, temporarily disable the firewall on the Mac and disable IPV6 on the computer.

  • Solaris 8: Multiple primary interfaces connected to the same network

    I have a machine with Solaris 8, and it has multiple interfaces that are connected to the same network which means they all have metric 0 (1 hop) to the default gateway.
    assume:
    e1000g0: 192.168.30.70
    e1000g2: 192.168.30.72
    e1000g4: 192.168.30.74
    e1000g5: 192.168.30.76
    gateway: 192.168.30.65 (Cisco Router)
    However, it seems like despite the fact that they have a direct connection, they seem to be using e1000g0 to access the 192.168.30.0 network to get to the default gateway and then to anywhere else.
    When I send a ping to say, 192.168.30.74 (IP of e1000g4) and capture packets on e1000g0, I see the "echo reply" messages going out of it as opposed to e1000g4 even though e1000g4 is the one receiving the "echo request". This should not happen and these should be completely independent as they should all be advertising a 1 hop to that network
    The outputs from netstat -rn and ifconfig -a are shown in the picture on the link below
    [http://img836.imageshack.us/img836/7308/ifconfignetstathiddenip.jpg]
    This gets even more confusing when I go into the Cisco router and run the command: "show mac address-table" where only the MAC address of e1000g0 is shown for the switch port it's connected to, but not for the other interfaces which are connected to the switch. Yes, all ports are active (no shut) and are pingable.
    Also, the odd thing is that ALL of these individual MACs show up in the router ARP table when the machine comes up, however after sending a ping to one of them, after a certain expiry or whatever period, the MACs disappear from the router ARP table and only the MAC for e1000g0 shows up. The arp table of the solaris machine however shows all the relevant MACs of each port of the router that it's physically connected to (This is actually a Cisco Switch with the advanced IP services imagine and L3 routing turned on)
    Before anyone asks: The setting local-mac-address? setting does NOT exist in my machine and it never has, but it used to work fine. Also, from the ifconfig command, once can tell that all the MAC addresses are fine.
    I need to somehow assign all these interfaces equal priority and make them understand that they're physically connected to the 192.168.30.0 network and there's no need to go through e1000g0 to get to it.
    This is causing a lot of problems as eventually all traffic will end up going through the e1000g0 interface and that will become a bottle neck.
    Please help Thanks in advance

    Ok thanks. That was a useful response.
    I did think about the trunking software that is claimed to be available for Solaris 8, but it's only available if you've got paid support contract. Oracle came and ruined everything re: Sun support which is so expensive now.
    The other confusion is, we never had that OR needed to configure trunking/link aggregation on this machine, so why now?
    Lastly, by your explanation, this should be expected and is "normal" behaviour, which would mean that this machine was always doing this and I only just noticed it this time? I thought if you turn off ipv4 forwarding and router function in the machine, it's every interface for itself. But it's not doing that :(
    So then the question is, Can I force it? I've tried a bunch of things by manipulating the tables and it seems to mess things up where nothing is getting through or it now shifts all the traffic to some other port make the problem no different
    Is there a way to give equal weight to all interfaces for the traffic to go directly through them that is originating at those ports?

  • Successfully set up TC (the latest one) for MBP. I can access to TC wirelessly.  Tried to access from my PC too but PC does not even detect TC (as storage), while PC is connected in the same network and can access to the internet.  Anything missed?

    Successfully set up TC (the latest one) for MBP. I can access to TC wirelessly.  Tried to access from my PC too but PC does not even detect TC (as storage), while PC is connected in the same network and can access to the internet.  Anything missed?

    Load the airport utility for windows.. it has several parts.. the key one is bonjour for windows which helps windows find apple network devices.
    The TC should also be setup with names that windows can use.. ie short, no spaces and pure alphanumeric.
    So Fred Blog's Airport Time Capsule
    Is not a valid windows name.
    TCgen5 is.

  • HT4061 Got new router my samsung galaxy will connect to my printer and eprint but Ipad won't connect keep saying connect to the same network  this ipad connected before but now it won't

    I had upgrade of new router my samsung galaxy can connect to my printer and eprint but my ipad won't  it says connect to the same network my printer is hp deskjet 3550A printer my ipad connected to my last router

    Hi Pvclayton,
    If you are having issues with AirPrint on your iPad, you may find the following article helpful:
    Apple Support: AirPrint Basics
    http://support.apple.com/kb/HT4356
    Regards,
    - Brenden

  • My apple tv was working fine untill the AirPlay option disappeared. I haven alterd the settings and have tryed rebooting both iPhone and ipad. I even rebooted the ATV and that disn't work. i am connected to the same network on both devices to.. Help

    my apple tv was working fine untill the AirPlay option disappeared. I haven alterd the settings and have tryed rebooting both iPhone and ipad. I even rebooted the ATV and that disn't work. i am connected to the same network on both devices to. My iPad is up to date but my phone isn't but as I said mirroring and AirPlay worked fine on both devices befor...

    Hi F1N5G10, 
    Thanks for contributing to the Apple Support Communities. 
    It sounds like you don't have the AirPlay option on your iOS devices. Restarting your Apple TV and iOS devices was a good first step, and you can find some additional tips to guide your troubleshooting at this link:
    Resolve issues with AirPlay and AirPlay Mirroring from iPhone, iPad, and iPod touch - Apple Support
    Sincerely,
    Jeremy 

  • How do you get two computers on same network for mirgration.

    I am trying to migrate from an older iMac G5 running the most updated version of TIGER to our new MacBook Air running LION.
    The air doesn't have a firewire connection, so it's trying to do it over the wireless network.  I have them both on the same network, BUT the new Air is asking for me to update the Migration Assistant on the older machine.  Don't have any idea how to do that.
    Is there a work around? 
    Can I use USB connections?

    You need to install 10.5.8 on the PPC computer to work with Migration Assistant. It would be easier to clone the drive to an external hard drive. Then restore from the external hard drive using Migration Assistant.

  • TS2235 Hi, how can I print from my IPAD to my wireless HP 6520 printer.  I have a wireless network and my IPAD and wireless printer are connected to the same network.  But when I send a job, I get the "no air printer found" message.

    My windows firewall is disabled (protected by Comcast's Norton program) so that should not be a problem.  Should I down load Bonjour?

    Hello Bleedingblue65
    Check out the section highlighted below to troubleshoot your issues printing through AirPrint.
    AirPrint Basics
    http://support.apple.com/kb/ht4356
    If you are unable to print, or if you see the message "No AirPrint Printers Found"
    Verify that the printer:
    Has power and is turned on. If it has power, turn the printer off and then on again to see if that resolves the issue.
    Is connected to the same Wi-Fi network as the iOS device.
    Has the latest firmware version installed.
    Has paper with enough ink or toner installed.
    Is free of any errors displayed on the printer's control panel.
    If necessary, consult the printer documentation or contact the printer vendor for help with the above steps.
    Notes:
    AirPrint printers connected to the USB port of the Apple AirPort Base Station or Time Capsules are not supported with AirPrint.
    Some Wi-Fi AirPrint printers can take several minutes to join a Wi-Fi network after being turned on. Ensure that the AirPrint printer is connected to the Wi-Fi network before attempting to print.
    Regards,
    -Norm G.

  • 2 apple tv's won't connect to the same network

    Hi I have 2 apple tv's but they won't connect at the same time.  It's not the internet I'm running at 20.63 Mbps.  But if on atv is connected in one room the other will pick up the network and signal strength is at 5 bars but subnet mask, router and DNS all show n/a. If I go unplug the other atv it connects. What gives, any help would be much appreciated.

    Sparkybyday wrote:
      how would I know if there was sufficient IP addresses in the DHCP range? 
    Check the settings in the router.
    I suspect connecting one or both via ethernet would resolve the issue.  Also, if the ATVs have the same name, that may be part of the issue.

  • I have the new ipad retina however i connect it to the wifi at work the signal comes and goes, especially as soon as i use an app that requires wifi, my iphone 4s is connected to the same network with no such problems, why is my ipad giving me these probl

    I have had my ipad retina for two and a half weeks but since the week end every time i connect to the wifi network it joins then disapears as soon as i open safari for example or just disappears at intermittent intervals....i have my iphone 4s connected to the same wifi network with no such problems.
    I have tried resetting the network settings to no avail
    Does anyone have any suggestions?
    Many thanks in advanced. 

    I have had my ipad retina for two and a half weeks but since the week end every time i connect to the wifi network it joins then disapears as soon as i open safari for example or just disappears at intermittent intervals....i have my iphone 4s connected to the same wifi network with no such problems.
    I have tried resetting the network settings to no avail
    Does anyone have any suggestions?
    Many thanks in advanced. 

Maybe you are looking for