How do I connect my 13in (early 2011) MBP to my Sony Bravia KDL-26

Hi Folks,
I've recently bought a 13in MBP and want to output my HD video to the TV. Is this just as simple as Thunderbolt to HDMI? If not any ideas.
Cheers
Mark

Hi Folks,
It's easy, there's just a few things you need to know.
Bought the minidisplay to HDMI cable off ebay for about £6.00. Pluged in both ends OK. Had to disconnect the recorder first. Might have to look at some kind of splitter so I don't have to do this every time.
Select the HDMI input on the tele.
At first the TV will only display the basic Mac background picture (stars) You need to 'Mirror' the displays, and sort out the sound.
Go to 'System Preferences' and select 'Displays'. With the Mac plugged into the TV you get an extra tab (Arrangements) at the top of the box. Select 'Arrangement' and check the 'Mirror Displays' box.
Next from System Preferences select 'Sound'. Both 'Internal Speakers' and the TV are listed. Select the TV.
All should be working now.
HD video without Blueray - result!!
Cheers
Mark

Similar Messages

How do I connect my ATV to my Yamaha receiver, pvr, Sony Bravia, and DVD player?

Note: I am not very savvy with this stuff so basic lingo please ;) I have a lot of hdmi inputs & outputs. I had it all connected & working except for the surround sound wasn't playing for Apple TV. I have 3 hdmi's on the TV labeled 1, 2 & 3. The receiver has a "HDMI DVD IN1" and "HDMI DTV/CBL IN2" and then another that just says "OUT".
So I'm not only trying to figure out what to connect to each device but also by the numbers & in & out options.
Any help would be greatly appreciated.
Thank you!

If you want the ATV sending audio to the receiver, connect it to one of the inputs on the receiver.
Ideally, all devices connect to the reciever.
The reciever then connects via one HDMI cable to the TV.
That way all audio goes to the receiver and the TV merely acts as a monitor.
However, this may not work in all situations depending on the number of inputs on the receiver. Personally, I would replace the receiver with on that has at least 4 inputs, but that may not be feasible depending on your situation.

Apple TV doesn't connect with sony bravia KDL-40NX720 TV

I'd like to connect my apple TV (bought yesterday) to my Sony bravia KDL-40NX720.
I connect the Apple TV with the HDMI cable but it doesn't connect to the Sony.
What can I try?

Do you have a 2nd or third gen Apple TV? The problem may be you have 3rd Gen which requires a 1080i supporting TV and I am assuming the 720 at the end of your model number means it is a 720i TV. That would support 2 Gen apple TV but not 3rd. Is that possibly the problem?
Check which ATV you have and the tech spec of the TV. If I am wrong please post again so we can look at other issues.
Hope I am wrong by the way!
Jules

How do I connect my MacBook Air 2011 to a projector?

How do I connect my MacBook Air 2011 to a projector?

It depends on the input connection for the projector, but since many are rduced resolution, VGA seems to be the prevalent common connection.
It's just a matter of buying the adapter that adapts VGA to the Mini DisplayPort/Thunderbolt port on your Air. If it is a DVI or HDMI connection input on your projector, the online Apple Store carries that as well.
This adapter and sufficient length VGA cable is all you need for VGA.
Here's the DVI adapter.
For some reason, I am unable to bring up the Moshi HDMI adapter on Apple's site.

I'm selling my early 2011 MBP because I just bought a iMac. Could someone please tell me how to remove all my information from it but leave the OS working. Thanks so much.

I'm selling my early 2011 MBP because I just bought a iMac. Could someone please tell me how to remove all my information from it but leave the OS working. Thanks so much.

How do I securely delete data from the machine?
Erase, formatting, OS X installs on Mac's

AMD Radeon HD 6750M, Early 2011 MBP, 10.9.4 Problems

Hello,
Ever since 10.9.3 update I have a serious problem with my Early 2011 MBP with AMD Radeon HD 6750M card.
First my configuration:
MBP 2.2 GHz Intel Core i7 (Macbook Pro 8,2)
16 GB RAM
512 GB Sandisk SSD and 750 Stock HDD
AMD Radeon HD 6750M and Intel HD Graphics 3000
OS X 10.9.4
I'm usually using my MBP with external display with a resolution of 1920x1080. The display is connected via DVI to Mini Display Port adapter. When I connect the external display, my MBP switches to the AMD card. Here's where the problems begin. If I'm using Davinci Resolve, Capture One Pro or any other software (that I use regularly) that uses the GPU extensively, the cpu usage will rise, the computer will start to feel sluggish and my productivity almost becomes none because even the simplest tasks such as opening another tab in firefox or safari takes anywhere between 1-3 sec. When the computer starts doing that, I cannot play a simple HD video at native fps and the whole machine basically becomes too expensive paper weight. The strange thing is that even after I quit all programs, the system cpu usage continues to be high, around 50% with kernel_task being the star using all this cpu and it keeps using all of this cpu forever, at least until i shut it down or disconnect the external display and manage to make it switch to the internal Intel gpu.
The problem started after istalling the 10.9.3 update and it's still there with the 10.9.4 update. I even formatted the computer and reinstalled everything but the problem still persists.
I haven't experienced anything like this on 10.9.2 and the machine was actually quite fast before that. Now, I have too expensive paper weight on my desk.
Since the problem is very specific, I doubt many users will complain and I doubt Apple will ever do anything to fix it, at least until hopefully the new drivers in 10.10 fix the issue hopefully.
My question is:
1. Has anyone else experienced this and managed to solve the problem?
2. How can I downgrade to 10.9.2? I don't have time machine backup but i have bootable usb with 10.9.2. Will it help?
All best,
Goran

When you have the problem, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
☞ Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
Open LaunchPad. Click Utilities, then Console in the icon grid.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above. Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first. Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

Can't install windows 8.1 on early 2011 MBP

Hey all,
I'm having problems installing Windows 8.1 on my Early 2011 MBP (MacBookPro8,2). When my superdrive died I installed an SSD for the boot drive and kept the original hard drive as a secondary drive. I used BCA (modified to support USB) to create a USB 2 Windows 8.1 install drive from an ISO I previously created. I also had it partition the hard drive. When it reboots I get the "no bootable device found" and blinking cursor issue. I've tried holding down option and choosing EFI, but i've picked up during the last week that installing through EFI on my MacBook Pro isn't possible. Does anyone have any ideas on how to solve this?

I ended up coming across this last night:
http://malwaretips.com/threads/installing-windows-on-a-mac-with-a-damaged-superd rive.32474/
I am in the process of testing this out, but currently I'm stuck with an issue with winclone not expanding the image of the usb install disk to use all the space in the partition. However I did boot into the Windows installer and didn't run into the "couldn't find partition" , "no bootable disk", or "not an MBR" errors I've seen before.
I Think the key for non supported hardware and Windows 8 or later is to create the bootable usb in windows and not through BCA. I actually used the VMWare Fusion trial and a windows 10 technical demo image to do the monkeying around in windows. Hope this helps someone else. I'll keep updating.

Lately, I've been getting a blue screen in the midst of working and have to do a cold reboot to end it. Seems to happen when I'm closing windows or quitting applications. Not always, but sporadically. What causes this? I'm using 10.6.8 on early 2011 MBP.

Lately, I've been getting a blue screen in the midst of working and have to do a cold reboot to end it. Seems to happen when I'm closing windows or quitting applications. Not always, but sporadically. What causes this? I'm using 10.6.8 on early 2011 MBP. Thanks for any help/advice!

You have 10.6 on that machine, I suggest you stick with it for performance, third party hardware and software reasons as long as possible.
Consider 10.8 (not 10.7) when it's released, because 10.7 and 10.8 will require a new investment in software and newer third party hardware as it requires newer drivers the old machines won't have. (forced upgrade because of software, really nice of them)
http://roaringapps.com/apps:table
Far as your Safari problem do these things until it's resolved:
1: Software Update fully under the Apple menu.
2: Check the status of your plug-ins and update (works for all browsers) also install Firefox and see if your problems continue. You should always have at least two browsers on the machine just in case one fails.
https://www.mozilla.org/en-US/plugincheck/
Flash install instructions/problem resolution here if you need it.
How to install Flash, fix problems
3: Install Safari again from Apple's web site
https://www.apple.com/safari/
4: Run through this list of fixes, stopping with #16 and report back before doing #17
Step by Step to fix your Mac

Early 2011 MBP 17 Random Shutdown and Battery Behavior

Hi all, new to the forums here.
I recently purchased a refurbished early 2011 MBP 17' 2.2 Ghz i7 with 8gb and 10.7.5. Out of the box, machine looked great, but I noticed that the power cable was different than the one I had for my early 2011 MBP 15' I have for work. This raised an immediate redflag (buying from a refurb site outside of apple is always a cause for concern IMO) so I abstained from using that charger until I knew a little more. I plugged in the machine and booted it up and everything worked great. The batter was close to 100%, so after charging for approximately 20 min, I unplugged it, and the laptop immediately died. I powered it back on, and the harddrive began to spin for a few seconds, then the same result, total loss of power. Started up again, and I was able to boot into OS X and play around for a bit for a period of time before again, shut down.
For the next few days, same story. I was able to at one point, drain the battery completely and do a full cycle charge. The first time I did this, no change in behavior. Again, a few days later, I was able to drain the battery and perform a full cycle charge, but this time, a major change in behvior. Since the second full cycle charge, I have had absolutely no power problems. I haven't really "pushed" my MBP to see if fully utilizing the CPU/RAM/GPU will produce the similar results I had early, but it appears that everything is working great.
Here a few interesting notes to my situation.
When I was first operating the system (when plugged in, there were no shutdowns, only while on the battery) I pulled up my system report, and noticed that my battery cycle was very low (~5). This seemed odd, because I had opted for a used battery instead of a new one.
Prior to reinstalling Mountain Lion, my volume up key would trigger a few strange events. The screen for briefly get quite bright, then all open applications + the doc and widgets would restart (similar to killing explorer.exe in the windows task manager).
Since performing the fresh install, I have had abslutely no issue with my MBP and I love it, its a beautiful machine. However, as I purchased refurb, I'm hesitant to proceed (I will exceed my return period in ~2 weeks) without knowing my machine is in prime working condition. I have read issues about early 2011 models having issues with batteries and GPUs, but my symptoms were dissimilar to those described by others with those particular issues.
Any thoughts?
I have a genius appointment tomorrow evening for a general diagnostics check, but if others have experienced these issues, I would appreciate some input.

Do a SMC reset:
http://support.apple.com/kb/ht3964
Run an Apple Hardware Test:
http://support.apple.com/kb/ht1509
You may need to use OPTION D to start it.
Install iStat pro and open Activity Monitor. Set Activity Monitor to show 'All Processes' and '%CPU' to display values from high to low. Post images of the two such as these:
Ciao.

My early 2011 MBP 13" does not recognize my Sandisk 16GB 45MB/s Extreme Pro SDHC card. I went to the Genius Bar and we tried it in all the MacBook Pro's in the Apple Store and NONE could recognize the card. However, iMacs did. Any suggestions?

My early 2011 MBP 13" does not recognize my Sandisk 16GB 45MB/s Extreme Pro SDHC card. I went to the Genius Bar and we tried it in all the MacBook Pro's in the Apple Store and NONE could recognize the card. However, iMacs did. Any suggestions? Genius behind the Bar suggested wait for LION OS X release...

You really don't need to post multiple times, you will get attention eventually.
Find the reply here:
MacBook Pro 13 (MBP 8,1 random restarts)

Does anyone know if this HD works with a early 2011 MBP?

Looking to upgrade my internal HD on my early 2011 MBP. Before placing the order, would like to get some professional advice.
The HD being considered is:
SAMSUNG Spinpoint M9T ST2000LM003 2TB 5400 RPM 32MB Cache SATA 6.0Gb/s 2.5" Internal Notebook Hard Drive
Thanks in advance for all advice/inputs

Oh, sorry, I didn't note that I am planning on using logic 8 to attempt this. I don't have access to a machine with logic and pro tools installed to try it myself, else I would.

Installing Windows 7 on Replacement SSD in optical bay Early 2011 MBP

So i just bought a 120gb SSD and a optical bay enclosure that i installed into my early 2011 MBP. I also bought a optical drive external usb enclosure. I was hoping that I could use bootcamp to install Windows 7 onto the SSD but when i go through the bootcamp menu and my laptop restarts im stuck with a blank black screen. Ive also tried using bootcamp to create a bootable USB (which i had to do a work around to get to work because it supposed to only work for MBA) that didnt work. Can anyone help?

ANYONE???

Early 2011 MBP - Won't install updates?

Today was the first time I've used my MBP since finishing school for the year and I decided to try and install whatever new updates were recently released. However, whenever I hit the option to restart my mac to install the updates it... it seems to just return me to the log in screen, and when I check my Software Updates they're all still there waiting to be installed.
Help?
It's an early 2011 MBP, running OSX Snow Leopard 10.6.8. 2.3 Ghz Intel Core i7 with 8GB RAM - if that helps at all.

Yeah, that probably would've helped, huh?
The latest iTunes, iDVD, iMovie, iPhoto + the latest firmware and security updates.

Early 2011 MBP Slowing Down

Hello, I have an early 2011 MBP (15-inch), system report below:
MacBook Pro (15-inch, Early 2011)
Processor: 2 GHz Intel Core i7
Memory: 16 GB 1333 MHz DDR3
Startup Disk: Macintosh SSD
Graphics: HD Graphics 3000 512 MB
Lately, my MBP has been slowing down a lot.
I tested out a bunch of flash sites, but it does not seem to be the problem. Like I said, I have 16gb of RAM (combined with what I have located above, i7, etc), and have had numerous flash sites up, but no slowdown. The problem is recent, in that I've noticed it in the past 6 months. Nothing changed in that period at all to cause this problem.
I've run this setup for a couple years without issue (SSD where the DVD player used to be, and the HDD where the old HDD was located), without issue.
My MBP gets so hot that I have to move it frequently for scare of erythema eb igne (stupid technical term, but I might not be joking, and would rather not joke around about something like that.but seriously it get that hot where your only option is to shut off the MBP. I know that might sound extreme. But my MBP gets that hot. Especially if you are running a program like Premiere. I understand the power and RAM that it takes to run a program like that, but it was shocking. This is a program (Premiere) I ran without problems previously..
Checking activity monitor (and iStat), RAM does not seem to be the issue. CPU seems fine 88-90% usage,
Usually have 7-8GB of RAM available, and the CPU usage under 90%.
I have no idea, but I will be taking a can of compressed air to the MBP.
I was just wondering if anyone had any other ideas or had similar situations to help me out?
Thank You,
T

When you see a beachball cursor or the slowness is especially bad, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.
When you post the log extract, you might see an error message on the web page: "You have included content in your post that is not permitted," or "The message contains invalid characters." That's a bug in the forum software. Please post the text on Pastebin, then post a link here to the page you created.

Which kind of SSD hard discs do support with earlier 2011 MBP ?

Which kind of SSD hard discs do support with earlier 2011 MBP ?
I'm using 15 inch earlier 2011 MBP. I would like to replace hard disc to a new SSD hard disc to improve performance. But I don't know which kind of SSD works fine for it. Does anyone work fine? Could you give me some successful experience? Thanks a lot.
BTW, Can I use SATA3 SSD? And any problems here?
Thanks a lot!

is it a hard questions?

How do I connect my 13in (early 2011) MBP to my Sony Bravia KDL-26

Similar Messages

Maybe you are looking for