How do I connect to cellular network in Tokyo (Narita)

I just landed in Narita and can not seem to find a cellular network connection.  Any ideas?

Do you have international roaming enabled on your phone?  Need to have that enabled before you can pick up local networks.

Similar Messages

  • TS1368 how do i connect to the network off my itunes? its saying theres no interenet connection even though there is

    how do i connect to the network off my itunes? its saying theres no interenet connection even though there is

    Yes and I do understand that! Thank you. There is no option to do an auto channel. Its 1-11 or 36, 40, 44 or 48. Then when it asks for a security its 40 bit WPA or 128 bit WPA. Unsure what that means? If I choose either of those Security options I have to have a certain number of characters for my password, and neither of those options fit the password that was given to me.
    Any suggestions?

  • IPhone 5s won't automatic connect to cellular network after the wifi connection lost.

    My iPhone 5s won't automatic connect to cellular network after the wifi connection lost. I have try make a restore and open again my cellular data but the problem is still there, after I try to restart my iphone then can use my cellular data, but after few hour ago I still confront the same problem too.

    I also tried a total reset. But it didn't work.

  • HT4061 I have iphone3GS and its unable to connect to cellular network. I am not sure whether it can be resolved? If so how much it would cost me?

    One of my friend purchased Apple Iphone 3GS an year back. But due to various reasons, he did not use the phone. But when he recently tried using it, Its unable to detect the cellular network.
    I see that the  product warranty period is over and now not sure whether it can be resolved? If it can be, guess, it would cost me more. Is there any help someone can provide me in this issue to have it resolved?

    Is the phone activated?  Tell your friend to contact the cell provider.

  • New iphone 5 will not connect to cellular network

    got new iphone 5 and can't get it connected to at&t cellular network. help.

    Read this it might help you http://www.apple.com/au/support/iphone/assistant/wifi/

  • Cannot connect to cellular network after 6.1.2 upgrade

    I just upgraded my iPhone 5 to 6.1.2 this morning via an over-the-air update on my WiFi network. The upgrade appears to have been successful, however, it can no longer connect to the Verizon cellular network.
    I tried restarting the device, but no luck.
    I tried turning Airplane mode on and off....no luck.
    I confirmed that Celluar is on in the General settings.
    My wife's phone and my phone are on the same Verizon account and I had service (full bars) just prior to performing the upgrade. My wife's phone has not been upgraded and it still has full bars.
    I'm at a loss as to what to do next.

    I tried resetting the phone back to the factory settings, but still had the same problem. I made an appointment at the Apple Store and took it in.
    I told the tech everything that I tried and he checked a couple of other things behind the counter. Ultimately, he diagnosed it as a problem with the SIM slot on the phone--he took the SIM out and it didn't give him a "missing SIM" message (or the like) which apparently the phone is supposed to do when you remove the SIM.
    He replaced the phone with a new one. Fortunately, I had all my stuff backed up on iCloud so within about 20 mins, my phone was back to normal (less all my music content, which I synced when I got home.)
    The tech mentioned that the troubleshooting steps I tried were sound, so if you experience the same problem give varjak paw's suggestions a try first. :-)

  • Power Mac Dual 1.8 Ghz: How do I connect to wireless network?

    HELP!!!
    I have this Power Mac Dual 1.8 Ghz with 10.4.11 OS. I used to use wire cable to connect the internet, but now the place I rent recently only provides wireless network. I was able to connect wireless network with my Windows Laptop.
    Question: How do I connect my Dual 1.8 OS 10.4.11 with wireless network? I only see Internal Modern, Built-in Ethernet and Build-in FireWire options.

    You can go the OWM route and get the airport extreme card and antenna
    http://www.dvwarehouse.com/Apple-Airport-Extreme-Wireless-Card-802.11G-M8881-p-3 1367.html
    http://www.dvwarehouse.com/Apple-Airport-External-Antenna-for-G5-2004-2005--MacP ro-Early-2008-A1066-922-6043---NEW-p-33986.html
    Google the part numbers for more vender choices,
    Or, you need to get a PCI WiFi card and antenna. BDAqua or Japamac have posted alternatives which are actually a little cheaper than the Apple parts.
    The third alternative is a USB-based wireless adapter.

  • Unable to Connect to Cellular Network - iPhone 3g

    I have not had a connection to my cellular network in over 2 days. It keeps telling me I have "No Service".  I have been in contact with the carrier multiple times and it does not appear to be an issue on their end. I have reset the network connections, reset all general settings, did a complete restore on itunes (which told me my SIM card was bad), so I went and got a new SIM card from my carrier and still nothing!  The folks at my carrier store have never seen this before.  It's like the phone just will not connect to cellular.  I have had the phone for 2 years and have never experienced anything like this before.
    Has this happended to anyone else before? Is there any way to fix it?  The phone works great, so I don't want to get a new one unless I really have too.
    Please HELP! Thank you!

    Hi, I have the same issue as you with my iphone 5, when i connect to my router at home I only get less than 1 megabites, but with my other iphones (i4 and 4S) don't have this problem, I can get up to 15 megabits. I sent my i5 to apple care and they said that my phone is ok and returned it to me without fixing it.
    I live in Spain, so it is possible that in ihe US Apple is more carreful with its customers and will fix this problem!!!

  • IPad not staying connected to Cellular network

    My Husband has an iPad wifi/4G with AT&T service. It is not maintaining a connection to the Cellular network. We have taken it to AT&T and had the SIM card replaced as directed by AT&T Customer Care. This didn't help.
    It will randomly connect when he is out but not in our home. This is a new problem as it has always connected before.
    Is this something we should take it to the Apple Store for? or possibly does it need repair? Of course he Applecare has expired
    He works out in the field and needs it to connect.
    Thanks for any help.

    Hello Maggie Vansickle,
    Thanks for using Apple Support Communities.
    From your post I understand that you're having connectivity issues with your iPad's cellular connection.  To resolve this issue please follow the steps below.  Note, that even though it states it is for iPhone, the same steps apply to your iPad cellular connection.
    No cell signal strength anywhere
    Verify that your carrier name appears in the status bar, at top left of the display.
    Turn Airplane mode on, wait for the to appear in the status bar, and then turn it off again.
    Reset Network Settings: Tap Settings > General > Reset > Reset Network Settings.
    If your iPhone is in a case, try removing it to ensure that the case isn't interfering with the cell signal strength.
    Contact your carrier to find out the following:
    If you are in an area with network coverage.
    If there is a network outage.
    The account is properly configured to your phone.
    Try to restore your phone and set it up as new.
    Issue not resolved
    My issue is still not resolved. What do I do next?
    Contact Apple Support.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Take care,
    Alex H.

  • I am using iphone4, i can not connect to cellular network, i am using iphone4, i can not connect to cellular network

    need help.. i can't connect to cellular network

    What did your cellular carrier say when you reported the problem to them?

  • How do i connect to a network with cifs

    I'm looking to buy a Netgear NAS drive and I have an issue trying to figure out how I'm going to connect with it.
    I have macs running 10.6 and 10.8 and according to the manufacturers the only way to connect is using the CIFs protocols.
    Does anyone have experience and knowledge to share on this kind of set up and if this is the best way to set up a home NAS systems?
    The other question I have is I read that a CIFs configured networks can only handle file sizes under 4gb, is this true?

    Yes 4 GB is the limit for CIFS or SMB.
    Once you know the IP use like...
    smb://10.0.1.5
    smb://192.168.1.3
    cifs://10.0.1.5
    cifs://192.168.1.3
    I'd avoid a NAS drive despite the Rage, I'd opt for a Mac Fornatted external drive.

  • How do i connect printer over network to macbookair

    Hi I have a macbbok air with mountain lion os, and am trying to connect an epsonsx130 printer throught my d link (sky) router. I have been through the print n scan method, but my p[rinter does not show, no matter how amny times I have tried. Any suggestions???

    Hi Kirsty,
    If you are having issues accessing a network printer from your MacBook Air, you may find the following article helpful:
    OS X Mountain Lion: Troubleshoot a network printer
    http://support.apple.com/kb/PH11070
    Cheers,
    - Brenden

  • How do i connect to a network printer or map a network drive?

    I have a MacPro on my work network and can only attach to the networked printer via IP address. The printer driver is on the print server and I have a path name but I do not know where in my MAC to input the network path/drive.

    First install the printer driver on your Mac.  Then add the printer in System Preferences > Print & Scan.  Beyond that, specific settings for the printer & protocol depend on the printer & network.  You may need to call your helpdesk for assistance.  Exactly what  make/model printer is it, and how is it set up on your network?

  • How do I connect an ethernet network printer?

    I'm trying to connect to an ethernet printer (Xerox WorkCentre 7428) on my LAN using a new Airport Extreme. I've tried connecting the ethernet cable via a switch, and also connecting directly into the ethernet ports on the Airport with no success.

    From Xerox's manual for that printer:
    To see the IP address of the printer, press the Machine Status button on the printer control panel. The IP address is displayed on the left of the touch screen.
    More from Xerox's support site:
    Solution : Configure the Printer to Automatically Obtain an IP Address (From a DHCP Server) From the Control Panel
    Login as the System Administrator or Key Operator. See the Related Items below for additional information.
    Press the [Machine Status) button on the control panel.  The Machine Status tab will be displayed on the Touch Screen.
    Select the [Tools] tab.
    Select the [System Settings] button.
    Select the [Connectivity and Network Settings] option from the Group section.
    Select the [Protocol Settings] option from the Features section.
    Select [IPv4- IP address Resolution], and then select the [Change Settings] button.
    Select [DHCP], and then select the [Save] button.
    Select the [Close] button.
    Press the [Log In / Out] button on the Control Panel. A "Do you want to reboot the machine now for settings to take effect?" message will be displayed.
    Select the [Reboot Now] button on the Touch Screen.
    Assigning the printer a static IP address (that is, one not assigned using DCHP) consistent with your AirPort Extreme's addressing scheme is preferable for printers. Instructions describing that very fundamental task are annoyingly absent from its manual though. At Step 8 in the above, see if there is an option for a static IP address. Specify one as I described earlier.

  • I am Egyptian , i have I pad 2 3g how i can change the cellular network

    hi
    Dalia from Cairo , Egypt
    i have i pad 2 3g from U.S A and its locked to AT&T , and this network didnt work here  i want to change the network to our local network
    thanks
    Dalia

    A GSM 3G iPad purchased in the US will not be locked to any carrier, so it will work anywhere. Make sure you don't inadvertently get the Verizon version which will work only with Verizon.
    Regards.
    Forum Tip: Since you're new here, you've probably not discovered the Search feature available on every Communities page, but next time, it might save you time (and everyone else from having to answer the same question multiple times) if you search a couple of ways for a topic, both in the relevant forums and in the Apple Knowledge Base, before you post a question.

Maybe you are looking for

  • How to Re-Run 100 scheduled reports at one time on failure of running?

    Hi All, I scheduled 400 reports in the Crystal Reports Server. Suppose, out of 400 if 100 over reports are failed to run due to various reasons then how to filter and Re-Run only those 100 reports at a time without triggering each and every report. P

  • Jiggle mode in Lion

    In Jiggle Mode (within Launchpad) should I have an "x" on the app icons to remove them if I want to?  Currently there's one app that always has an x, it's Caffeine, but no others ever do. 

  • My .jar and .jad files are not launching

    Hello everyone! I have a problem with my files stated above. I am unable to open them. I see a yellow key at the top right corner on the icons. I Have checked them. They don't have QT errors either. I have gone through the D and Z drives by Xplore bu

  • Transport process

    Hello all, We are currently looking at using SAP WAS 6.40 in an enterprise web service context. We have investigated the development environment and we found quite some stuffs. We are continuing and are currently looking at the change management proc

  • My hp laptop will not start up the screen states primary battery (601) im running a dagnostic test

    My screen states primary battery (601) I was on it last night. It just stop I couldn't even logoff and I can't get it to start up.