How do I contact a Advantech PCL-724 card with Lab View

I'm trying to get started and make a simple control program for a Advantech PCL-724 card. I want to use LabView but I don't know what kind of communication-device I'm suppose to use. I managed to control the card with a program called Genidaq but not with LabView.

You have to go to www.advantech.com and take where LabVIEW drivers for
your card and install it.
HeFo wrote:
> I'm trying to get started and make a simple control program for a
> Advantech PCL-724 card. I want to use LabView but I don't know what
> kind of communication-device I'm suppose to use. I managed to control
> the card with a program called Genidaq but not with LabView.

Similar Messages

How to configure a shell and tube heat exchanger with Lab VIew to get data

HiI
In our undergraduate chemical engineering labboratory we want to configure our shell and tube heat exchanger with a DAq and Lab VIEW to get information about the temperaure (of the cold fluid stream being heated), the pressure (of the steam on the shell side of the heat exchanger) and the flowrate (of the water being heated).
Can anyone suggest thermocouples, pressure transducers and flowmeters to fit between the heat exchanger and the DAq?
P.S. the heat exchanger is already fitted with thermometers, a pressure gauge and a rotameter but we don't know how to connect these hardware to the DAq
Solved!
Go to Solution.

It sounds like you have enough information to pick out appropriate sensors, you just need to do the research. I would start looking through the Omega catalog, or give them a call - they're usually helpful. I can't take the time to spec out parts for you - that would be a lot of time spent on someone else's project. Most pressure sensors put out either a 4-20mA or 0-5V signal, either of which you can read through an analog input on a DAQ; measuring a 4-20mA signal requires a resistor to convert to voltage. Most of the NI DAQ boards can read a thermocouple on an analog input, but make sure that your hardware does support reading thermocouples. For accurate readings, use a device that has built-in cold junction compensation - for example, the SCB-68 connector block - and for the most accurate readings, get a board specifically designed for temperature measurement.
For the flow measurement, a standard, simple solution is an orifice plate. You put a differential pressure transducer across it, look up the appropriate equations, and use them to calculate the flow rate given the density of the fluid (which you'll be able to calculate from the pressure and temperature, since steam tables are widely available). There are other differential pressure devices available as well - at a previous job we used a V-Cone from McCrometer. If you call them they'll spec one for you - but get an approximate cost first to make sure it's within your budget.

How can I order 2 or 3 different cards with iPhoto ?

How can I order 2 or 3 different cards with iPhoto ?

See this document on the details for shipping of Apple print products:
http://store.apple.com/us/help/print_products
There is no way to combine orders for different products into one.

How can I use the NI PXI-6508 with Lab View 7? what are the first steps to get started??How can I use the channels with lab view 7????

I have a 8 slot PXI system with 2 NI PXI 6508 and 1 DMM 4070 in it. I want to get started with programming the digital I/O cards (6508)! How can I use this cards with LabView 7?what is the best way to get started, or where can I get examples showing how to use the several channels?
Thanks!
Philipp

Philipp,
The best way to get started is to decide if you want to use traditional NI-DAQ or NI-DAQmx. Recently we released NI-DAQ 7.1 which provides NI-DAQmx support for the PXI-6508. In my opinion, NI-DAQmx is more efficient and much easier to use.
To get started with examples, simply launch LabVIEW and go to Help>>Find Examples. Then expand Hardware Input and Output>>DAQmx and select the appropriate digital group for your application. This should help get you started.
Please repost if you need addition assistance. Good luck with your application!

How do I stop iSync from syncing address cards with no telephone mnumber ?

I sync my Nokia to my Mac using iSync 2.3. I used a smart group made from email domain names to sync with my phone. IN this group are a number of address cards with no telephone numbers. How can I either delete them automatically, or disallow them from being synced to my phone ?

First, make sure that iSync isn't running.
Then, choose "Go > Go to Folder..." in the Finder and copy and paste the following into the dialog box that appears:
/Applications/iSync.app/Contents/PlugIns/ApplePhoneConduit.syncdevice/Contents/P lugIns/Motorola-K1.phoneplugin/Contents/Resources/
A window will open. Now, open the "PhoneConduit.plist" file in that window into TextEdit.
Do a search for "charsToKeep"
In the line below the one it finds it should read:
<string>0123456789+#*</string>
change it to:
<string>0123456789+#*p,</string>
(adding in the p and , characters) and save the file.
Quit and the reload iSync and sync. It will no longer strip the p and comma characters.
Apple obviously doesn't know that those characters can be accepted by the phone.

How to determine the slew rate of an amplifier using lab view

gud evening all
I have an op amp circuit built on the NI ELVIS board and I input a square wave from function generator to the circuit. I have to determine the slew rate of the op amp.In the labs, one would run the square wave over a range of frequencies and stop when the square wave looks like a triangular wave. At that frequency, one would then measure the slope of the signal and that will give you the slew rate. How can I do that in LabVIEW? How can I check when my square wave starts looking like a triangular wave? please help
good
good

thank you johnsold
i designed a voltage follower using 741, on an Ni elvis instrument. i can manually do the slew rate experiment by varying the frequency range on the coasre frequency knob( using a square wave) of the function generator until the slew rate occurs at 0.5volts, my problem is how can i do the same experiment with built in vi in labview with out touching the knob on the function generator and once the triangular wave starts to show the lab view program will automatically stop.
find attache my vi
good
Attachments:
slew rate.vi ‏21 KB

How to I contact Apple about a support issue with Game Center--itself, directly. I changed my Apple ID and now I cannot access my game center account that I had previously. It created a new one for me with my new apple ID instead of keeping the old one.

I want to submit an issue with Game Center--itself, directly. I had an account set up that I used to play online games. I changed my appleID and then I no longer could access my game center account. I, apparently, had a new game center account created for me (which is friends with my old account) and now I cannot access my original game center account.
If I can't get access to email apple directly (which seems ridiculously difficult to do), then someone please tell me how to FIX the issue.
Thank you

Yes. I have tried that. When I use the ID I had before, it sets it up as a new account and I don't want to lose my stats attached to my old account.
Let's say that my old nickname was "user10" and I used the email, "[email protected]" for my apple id. I changed my apple id to "[email protected]" and it changed my game center account to "mynew" and somehow I am friends with my old acct, "user10". I tried getting a password reset for "user10" but I apparently don't know my own birthday, which is possible because I usually give a false one, but the same false one each time.

I am a consumer, how can I contact someone at the corporate level with concerns?

In good faith I purchased a notebook (Pavilion G6) December 17, 2012, It was a gift for my sonwhowould be start community college in January 2013. On March 28th the computer died. I took the computer back to Best Buy where I had purchased it, the hard drive had to be replaced. This really concerned me that a new computer would have to have the hard drive replaced in 2 months of use. I picked up the notebook on or about April 18, 2013 only to have it crash againMay 8, 2013. I spoke with management at Best Buy (Curtis Pope) explained my concerns that the defective hard drive h ad been replaced twice, also defective CPU, the computer had cooling fan issues, and OS was restored, but again my request fell on death ears. On January 21, 2014 the computer died a third time and I took t back in to Best Buy and basically was told that the hard drive was bad and that it would be sent to GEEK Squad and that they would trade it out for a new computer and would not replace it for a third time. On February 1, 2014, I recieved a call from GEEK Squad stating that my waranty had expired and that they estimated the cost to repair the notebook was $150.00. I became very upset explaining the history of repairs and the fact that the manager had told me that usually the computer woud be switched out. GEEK Squad then called Best buy, add Best Buy called me to say that my warrany had expired and there was nothing that Best Buy or GEEK Squad could do for me. The GEEK Squad manager, Christine at store # 01437 advised me to call HP. I have called, but I have been passed around so many times, I Nee HELP!!!!

Hi:
You can contact the HP Executive Team at the link below.
https://ssl.www8.hp.com/us/en/company-information/executive-team/ceo-index.html

How can I contact Adobe support to get help with deactivating my cs4 license on a computer that I cannot access anymore?

My mac laptop recently went kaput. So I got a new one and I restored my most recent time machine backup to it. The restore went well, but I am not unable to open my cs4 programs.
When I try, I get a message that says "Licensing for this product has stopped working..." and it gives an error code 150:30
I have tried looking for solutions myself, but nothing that I have seen on the forums has been able to resolve the issue. As far as I can tell, I think that I have to reinstall my master collection and reactivate it, however, in order to do that, I think that I will need to deactivate my old version, that is installed on my dead laptop.
So, I need help with a couple things.
1. I need to get in touch with adobe support in order to get my license deactivated. But the new adobe support system just basically sends me to the forums without providing any way to get in touch with an actually adobe support person directly.
2. I think that I will need a link to download my install media because my original media came on a series of disks, but my new laptop does not have a disk drive.
Thanks in advance for your help.
Cheers,
James

Serial number and activation chat support (non-CC)
http://helpx.adobe.com/x-productkb/global/service1.html
OLDER previous versions http://www.adobe.com/downloads/other-downloads.html

How to arrange contacts in my Addess Book starting with the last name, re-doing them all at once, not individually. (I have 910 names in my Address Book).

This is a new computer. I see that my addresses have been arranged so that they read from the first name -- i.e. Jimmy Brown comes under 'J', not 'B'. I should like to put them all so that they read from the last name, first. I can do this individually but very much hope that there is a way that I can do ALL of them in ONE go? There are 910 addresses! Thank you very much, Frederica

First step is to set the address book to show last name and then the first.
Open the Address Book
Select View-Show Name As-Last, First
Then click on the column header labeled NAME to sort on that column.

No ISA slot available in PC. How can I use PCI-85 Modbus Plus card with Lookout?

My application is to communicate with two Modicon PLCs using Modicon's ModBus Plus (PCI based PCI-85) network card inside my PC, and using Lookout as an SCADA software. Since there is no ISA slot available in new PCs, I can not use Modicon's ISA-85 Modbus Plus networc card. But Lookout does not support PCI based PCI-85 card, how can I use PCI-85 card then, with Lookout? Why doesn't Lookout support it? I asked the following question from from the Modicon's representative about it:
If I purchase Modbus Plus Driver Suite CD (SWMXDS001, 05, or 10 etc),will I be able to use Lookout SCADA software (by the way, it supports standard MB+ prtocol) for my application? If yes, can I use any version of an
y of the ISA, PCI, or PCMCIA based MB+ card?
His answer was:
The Modbus Plus Driver Suite will talk to any version of card, PCMCIA, ISA, and PCI. The question now is will the SCADA package you are
planning on using be able to talk to the Modbus Plus Driver Suite? You must contact National Instruments and ask them if they support Modbus Plus, and if
they used the MB+ system developement kit to develop their product. Or if they wrote their own MB+ drivers, do they work with Modicon hardware?

Hi,
currently Lookout does not support the PCI-85 card. The only card supported for Modbus Plus is SA-85. Please see for further information:
Where can I Find Drivers for Communicating to PLCs, RTUs, and Other Industrial Hardware?
How to configure the SA-85 card for Modbus Plus
Hope this helps
Roland

How do I use a Verizon PC Wireless card with my iMAC Intel Core desktop?

Help! Bought a Kyocera KPC650 Wireless PC Card for Verizon wireless internet. Works fine w/ laptop because it has a slot. How do I configure my iMAC desktop to accept this card? Is there an external USB adapter? Or do I have to get one installed internally? Which adapter works with OX 10.4?
I've seen the Quatech U132 online. Will that work? Its $192!! As is the Sewell adapter too. ($209)
Any ideas? I want to get off SBCYahoo DSL and their router because our DSL line is damaged in our complex and no one is fixing it!
Thanks in advance.
tklines
iMAC Intel Core Duo Mac OS X (10.4.2) All-in-one

What protocol is Verizon using that is not compatible with the Airport Extreme built into your iMac? I have used Apple's Airport Extreme with a lot of different wireless routers with zero problems as all conform to either 802.11b or 802.11g standard both of which are supported by the built in Airport Extreme.

How to poll a text file with lab view

I am runnig a soft real time data collecting system for shop floor data collecting.reading serial port to list down data into text file. what is the best way of getting this data into labview?.polling of text file or some easy and quick method??

1.) If the data is coming in separate files, use the 'List directory' function to find out when a new file arrives. Then just read it using one of the standard functions, (i.e. Read txt file.)
2.) IF the data is being appended to a single file, use Open/Read/Close file functions. The read function will give you an offset value which tells you how far into the file you have read. Put that value in a shift register and then you can start reading where you left off when the file is updated.
I hope this helps.
"There is a God shaped vacuum in the heart of every man which cannot be filled by any created thing, but only by God, the Creator, made known through Jesus." - Blaise Pascal

How to get free memory size of a card with javax.smartcardio

Hi,
How can I find how much memory of a card is free with javax.smartcardio?
Please your advice.
Thank in advance.

gizmo wrote:
I wanted to read the free memory size with a card reader and javax.smartcardio.
Is it possible to send a APDU Command to select the root 3F00 and read the properties?There is no built-in smartcardio funationality to do this. What you can do is send an APDU and get the memory by calling the code mentioned already.

How to exchange lines when using dual sim card with 2 different pnone lines in the same iphone 4s

I have an iPhone 4S with a dual SIM card since I use 2 different phone lines (1 professional and 1 personal) They work well but, how can I change from one line to another without having to switch off the phone and then restart it introducing a different PIN?
Thank you

Hi raffettax,
Time goes by and I have no answer. There is lso no answer on Movistar Communities, the only one is really disappointing and is not given by a Movistar employee. An iOS beta tester told that beta 2 resolved the issue, but with beta 3 it stops working again .
Do you have any news about this issue?
Regards.

How do I contact a Advantech PCL-724 card with Lab View

Similar Messages

Maybe you are looking for