How do I correct version conflicts between host and RT engine?

I was running LabVIEW RT7.0 on a host PC (WinXP) and PXI-8145 system. I installed LV7.1 and LVRT7.1 on the host. However, the software versions in MAX still report as 7.0
I would like to upgrade to 7.1 on my 8145-RT. I cannot run 7.1 on the host and target the 7.0 RT engine (results in version conflict). Version 7.0 is installed on C:, but 7.1 is installed on D: due to space.
How can I get MAX to recognize my latest version (which should allow my to download it to the PXI)?
Thanks.
Laine

Thank you for the response.
C:\RT Images contains only a single folder for NI-PAL
However, I backed it up and copied the RT Images folder from D:, but still the same effect (MAX thinks 7.0 is the latest LabVIEW version).
D:\RT Images\LabVIEW\7.0 contains subfolders and install scripts (e.g., 7002.rts)
D:\RT Images\LabVIEW\7.1 contains subfolders but no install scripts. Also, there are many fewer files in these subfolders than in the 7.0 folder. I'm worried about trying to manually install from the 7.1 folder.
Any other suggestions? Thanks.
Laine

Similar Messages

Version conflicts between host labview and RT engine

there is problem that i cannt switch target to feild point. It said that "version conflicts between host labview and RT engine" . But my labview is version 7.0 and the real time module is version 7.0 too. Anyone can give me hand? Thanks

Depending on your version of MAX, you should be able to change the version on the FP (in remote systems). If you can't do it in 3.0, try upgrading to 3.1 (you will have to search for it on the site). If that doesn't work, you can try resetting to factory default and then see if you can do this.
Another tip, which for some reason seems to help, is updating the OS\Run-Time Engine when windows is in safe mode.
Try these and see if they help.
BTW, as a tip for next time, you're more likely to get a good answer for something like this if you post in the FieldPoint board.
Try to take over the world!

How can I resolve conflict between itunes and Windows 8.1

When downloading itunes to my laptop computer, using Windows 8.1 my email/network account will not work on that computer. It is fine on other devices such as ipad and Windows phone. I can also pick up emails on online on the same laptop. There appears to be a conflict between itunes and Windows 8.1

Please see Boot Camp for comments.

[vmware] Best way to share files between host and client

Good afternoon!
I have successfully installed VMware server on my machine and set up a virtual machine, powering Windows XP for study issues (emulation via wine does not do the trick for me). The virtual machine runs fast and stable but does not meet my requirements unless I have two issues faced:
First:
How to access a USB pendrive monunted by the host system properly within the client?
Second:
What is the best way to share file system space between host and client? Should I set up a Samba share which is accessible for both host and client or is it save to grant my VM access to my physical hard disc as a whole (using it as a partition)?
Thanks for answers in advance, I have still quite a lot to learn, when it comes to VMs.
Regards,
~cg

Do not setup your VMware to be able to access your physical disk as a whole. This would have you mounting the filesystem twice, corrupting it in the process.
You /can/ setup VMware with Sharing Folders that lets you share your filesystem (either / or just /home or something else) and that is what I would recommend.
As for accessing the pen drive from both operating systems at once, I'd say use the same Sharing Folders method. I always share /mnt so that I can access my cdrom/USB/etc from the vmware OS.
The sharing folders is basically the same as a samba share, but uses vmware's own method (HGFS). Samba is more secure (if you are worried about your VMware OS breaking from it's shell and attacking your real filesystem, which is unlikely). You need the vmware tools installed to make use of it.

Name space conflict between static and instance method

Hello,
there seems to be a very unfortunate name space conflict between static and instance method name. Consider:
static String description() that should return a description of a class.
String description() that should return a description of an instance.
That seems to confuse the compiler. How come? Static and instance methods don't have anything to get confused about.
Thanks for any insights :-)

Umm...jeez.
It's not a bug, it's the way it's supposed to be.
Since a static method can be called the same way an instance method
A instance = new A();
A.staticMethod();
instance.staticMethod();it's not allowed.
Also in the class, you can call
public void myMethod() {
instanceMethodInClass(); // You don't need this, it's superfluous
staticMethodInClass(); // You don't need the class name.
}If you didn't understand, then just accept the fact that it is so. Some day you'll understand it.

Error while trying to synchronize audio and MIDI. Sample rate 42804 recognized. Check conflict between Garageband and external device.

Sometimes, while playing back my software instrument songs, I get an intermittent pop-up error message, saying "Error while trying to synchronize audio and MIDI. Sample rate 42804 recognized. Check conflict between Garageband and external device."
(Sometimes the five digit number is different, but remains a five-digit number beginning with "4".)
Simultaneously, the song stops until I press the "Okay" button in the pop-up window.
When I continue to play the song, the sound is jerky and clipped, and the playhead doesn't keep up with the song, and then suddenly jumps to the part of the song currently being played.
There's also a sound of static.
The issue seems to occur whether or not I have my MIDI controller turned on and plugged into my desktop Imac.
Tony

Hello,
open your Audio MIDI Setup utility and set the input to 44100
https://discussions.apple.com/message/12710638#12710638

How can I tell if fan between front and rear bay is working?

hi all
How can I tell if fan between front and rear bays is working? I put my hand behind G4 MDD to feel for air flow and it seems minimal. I hear a wind tunnel sound but I feel more heat than air flow. Please help as I don't want my Mac to overheat
Thanks, Web dude

You can run your mac with the side "door" open - down flat to the right of the computer. You should be able to see the fan do (or not do) its thing.
I have done this (run the mac with the side open) many times. For safety, I turn the mac off before opening / closing the door.

[JS CS3] Conflict between palettes and panels

Hello,
I am having a conflict between panels and palettes. Hopefully I can get some direction without having to copy the code here, because it is very long.
I have a window of the palette type. This palette has buttons and radio buttons. The buttons call up various functions.
The radio buttons, however, make visible/invisible a series of panels in the palette. The panels are stacked upon each other, only one of which is visible at any one time, depending upon which radio button is selected.
One of the buttons in the palette calls up another palette (which also has a series of buttons for various functions). Let's call it the little palette. The problem is, that after the little palette is called up, the radio buttons in the big palette no longer work. I can select them but they will not make visible/invisible any of the stacked panels. The buttons in the visible panel work as well as all the other buttons that are always visible. The only thing that does not work are the radio buttons.
My only workaround is to just dismiss the palette and call it up again. But I'd rather fix this bug.
Any ideas? If I need to I can strip down the coding leaving only the essentials, but rather not take the time if this is a problem others have run into and hopefully have a solution for.
Thanks,
Tom

Thanks. I'll give it a try, but I even uninstalled both programs, tried
reinstalling Reader only, and when that didn't work, uninstalled Reader and
then reinstalled Acrobat. Still a problem. The particular website is
www.officeally.com, and it opens the PDF file in a browser window, I believe
using an ASP file.
Larry

Networking between host and qemu imag for telnet

Hello.
I want to start doing test and learning a bit about networking.
But I only have a computer, and it doesn't have even hardware emulation, making the use of any modern distro as a virtual machine painfuly slow.
So I downloaded a floppy distro.. and I manage to get a virtual network card working. But there is no ping between host and guest. I can't Telnet neither, of course.
Qemu man page and google are confusing me a lot. It speack of redirecting ports.. no solution to that
I don t have firewall, as I don't have Internet at home.
What can i do now? :S
Thanks in advance

I think I must stop drinking so much cofee on the afternoon, lol
Thank you very much for adding my reply!
bernarcher wrote:
vladimir_1922, the moderators receiveived this report message from you:
Yes, I checked that too... No result.
Maybe it is an issue with /etc/rc.conf. Some months ago it changed on the format who manages the network. May it be outdated?
Obviously, you did inadvertently use the "Report" button to submit this.
But don't worry, this happens quite often.
I tough a bit about the problem, and followed the steps on the Gentoo Wiki for sharing a conection between two guests, and I found the same problem, but with the vbe module being unabaible. After a bit of rage, I realized two possible workarounds:
First thing, is that I compile my kernel. As I don't have KVM or Hardware emulation, I just don't compile any virtual machine module, to save memory. BUT, I do have the /dev/net/tun device who qemu can't recognice (yes, I tried to run qemu as root), so It seems that it is compiled after all
The second thing, is that I also stripped the daemons and services at bootup, as I don't have Internet, or othercomputers, I don't need most of them. Between the services I don't start at bootup is the netwprk daemon... but if i try to start it, all it does is delay the bootup for almost 2 minutes looking for a network :S
So, I'll just copy my /etc/rc.conf, where I just did the changes of the wiki. Maybe I did something wrong, maybe I lack something.
Any help will be must appreciated
# /etc/rc.conf - Main Configuration for Arch Linux
# See 'man 5 rc.conf' for more details
# LOCALIZATION
HARDWARECLOCK=
TIMEZONE="Europe/London"
KEYMAP="es"
#CONSOLEFONT="Lat2-Terminus16"
CONSOLEMAP=
LOCALE=
DAEMON_LOCALE="yes"
USECOLOR="yes"
# HARDWARE
MODULES=(snd_pcm_oss snd_mixer_oss snd_seq_oss bridge tun)
USEDMRAID="no"
USEBTRFS="no"
USELVM="no"
# NETWORKING
HOSTNAME="arch.laptop"
interface=eth0
address=
netmask=
broadcast=
gateway=
NETWORK_PERSIST="no"
eth0="eth0 0.0.0.0"
br0="br0 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255"
INTERFACES=(eth0 br0)
gateway="default gw 192.168.0.1"
ROUTES=(gateway)
# DAEMONS
DAEMONS=(syslog-ng !network crond)

Software conflict between iPhoto and Sony MP3 player

I am experiencing a major software conflict between iPhoto and my Sony MP3 player (model: NWZ-E443). In the past, whenever I connect the MP3 to my 2009 MacBook Pro, iPhoto always opened. I would simply close iPhoto and everything would be OK, though. But after upgrading iPhoto a few months ago via an upgrade download I am now unable to view images full-screen. Although thumbnails display OK, when I double-click on any of them to display full-screen, the MP3's 'Do Not Disconnect' image displays full-screen instead, even when the MP3 is not connected.
I have tried reinstalling iPhoto from the original iLife disc, but this didn't work and my fear is that the Sony software has somehow corrupted every image single file in my library.

Turns out my Mac put code on the mp3 player because after I reset the mp3 player to its 'factory settings', (erasing everything) it went back to normal and now shows up in the finder window.

Conflict between VPN and Airport disk

Hello Folks, I just bought a brand new airport extreme 802n.
I thought it would be working fine with my Macbook pro, but it doesn't.
I can't access any externe hard disk or USB Stick through the airport extreme, although the format is FAT32. I checked and checked but found nothing useful. All the settings are default.
Worth to mention, I always use a cisco VPN client to get connected to the Internet (university student).
There are few times when I disconnected the VPN Client, the USB Client can be found and read, but not be written.
I though it is a conflict between VPN and Airport disk. So I tried without VPN, but the USB stick and the extern hard disk still didn't work properly. I have no idea what is happening could somebody help?
By the way is it possible to set Airport extreme as a VPN router so I don't have to use the cisco VPN client anyway?
Any reply is appreciated
Thank you !

I have an Airport Extreme connected to a cable modem
with comcast as my isp. The Extreme is connected to
a G4 dual processor mac via ethernet. I also have 3
airport expresses around the house to work as range
extenders. When I had the G4 connect to the Extreme
via its internal airport card, I had no difficulty
connecting to any of the Expresses around the house
with my g4 powerbook. Now that I have the G4 Dual
directly connected by ethernet to get the fastest
speed, I cannot get my expresses or my laptop to
connect through my laptop to the base station. all
lights are green on the expresses, but running
network diagnostics on the powerbook shows red or
yellow for the last two buttons on the right. Do I
have a configuration problem or an Extreme that won't
bridge properly?
Check that the G4 Dual has a location configured with
only "Built-In Ethernet" activated, and that its
Ethernet connection isn't shared on AirPort.
Turn off all your AX and check that your
PB G4 is able to connect to "your" AirPort network.
Take advantage of this silence of all your AX
to run an analysis of your wireless environnement:
- check that you don't have any neighbor wireless
network,
- check that on each of your AX settlement you have a
very good reception of "your" AirPort network.
If everything works fine to that point, add one AX to
your network, and check the reachability of your network
where you wanted to extend it.
dan

How to increase the width size between PROMPT and TEXT BOX?

Hi Gurus,
my page having MessageTextInputs. Normally page runs displays the Prompt name and one text box will displayed.
my requirement is
1) how to increase the width size between PROMPT and TEXT BOX?
2)prompt name displays like
elephant
xxxxxant
xxxxRose
here xxxxx indicates SPACE
but my client requirement is don't displays the SPACES in left side.
so our requirement is in page PROMPT displays like
elephant
ant
rose
How to achieve this plz help me
its very urgent
Thanks

Hi,
Create a table layout region and under that use 'messageStyledText' for displaying the prompt and use 'messageTextInput' for text field without giving any prompt to that.
--Sushant

How to stop any photo transferring between Mac and iphone

how to stop any photo transferring between Mac and iphone ?

This is a possibility. But please be aware using your Mac to emit a WiFi connection is a temporary solution. And it will get a short range unlike an actual WiFi Router. Also you may find it to be unstable at times. The Airport Card in your Mac was not designed to be a full time Router WiFi emitter. But more of a receiver to get the signal and use it for personal use.
1. Unlock the network on your Mac make it an open network
2. Go to your iPhone, Settings-Wireless-Tap on blue circle next to network name, Choose Forget network
3. Now go back, It will rescan and find an open network, Connect, and see if Safari works
If Safari works, Then you had a Security issue. Try using WEP 128 bit 13 character passkey or WEP 8 Character Passkey.
Cheers and best of luck
Message was edited by: Andrew T.

How can i get separate passwords between Apple and iCloud?

how can i get separate passwords between Apple and iCloud?

There the same account at this point so theres no way to segragate the password.
You could however make an icloud email address that is different then your primary apple ID that you use for messaging and itunes and apps stores but at this point you cant undo the password merge.

How can I make the fusion between CRM and SD?

I´m working in a company in Spain and I want to know how can I make a fusion between CRM and SD? It is posible? The company whants to move all the information from CRM to SD and work in the future only with SD departament. So all the database needs to translate at SD and SD departament use and work with twice module in one module. I haven´t idea if I can make this fusion, so please help me!!!!!! Thank you so much!!!!

Hi
Can you please more specific on following points. That will help to give you more input from all SDN users perspective.
1. What are the scenarios currently been used in CRM?
2. What are all TRANSACTION TYPES are used in CRM system?
3. Any development is done in CRM system which is important from BUSINESS PROCESS perspective?
4. Is there any MASTER DATA used in CRM, which will then replicate to ECC and then used in ECC also?
5. Are the middleware settings are done in CRM?
6. Last but not the least why your organisation does not want to USE CRM, which is one of the BEST ERP Package provided by SAP.
Regards

How do I correct version conflicts between host and RT engine?

Similar Messages

Maybe you are looking for