How do I delete a wireless network configuration?

How do I delete a network configuration?

Are you asking how to delete the network name and password? - you can use the Airport Utility to delete a password and not use security but you cannot delete a network name - you can only change it - but to remove the network name from showing up on the list of local networks in the area, you would have to turn off the wireless on the Express or Extreme which ever is the primary router

Similar Messages

  • How can I delete a wireless network from my MacBoork Ai

    How can I delete a wireless network from my MacBoork Air.
    I had set up a WEP Network but I need to set up a WPA (personal) network now and i cant seem to change the WEP network to a WPA2 network.
    Thank you for any help you can provide me.
    LShaps

    The MacBook Air will autodetect WEP and WPA security changes and should allow you to reconnect again. If the password stored in the Mac is wrong, it will ask you to enter it again.
    With that said, to forget a network do the following:
    - Go to the Apple Menu and select System Preferences
    - Click on the Network icon
    - Highlight the Airport / WiFi entry (sepending on 10.6 vs 10.7)
    - Click the Advanced button at the bottom
    - Make sue the Airport / WiFi tab is selected
    - Click on the network name you want to forget
    - Press the minus button at the bottom of the list.
    You may also want to consider restarting if you are having this issue.

  • How do I delete a wireless network from my "keychain?"  I need my Mac to not remember it at all.

    I am not able to get onto a friends wi-fi because we entered the wep incorrectly and it saved it that way.  I need to forget the network entirely and redo it

    Open System Preferences (gear icon) on the dock
    Open Network
    Click on AirPort or Wi-Fi on the left
    Click Advanced at the lower right
    Locate the name of the network and click on it to highlight it
    Click the - (minus) button at the bottom of the list to delete it
    Click OK, then click Apply
    Open Macintosh HD
    Open Applications
    Open Utilities
    Open KeyChain Access
    Locate the name of the wireless network and click it to highlight
    Delete that entry
    Restart your Mac

  • How can I delete the guest network from my airport. It was fine until the last update. It says my whole name's guest network which I do not want everyone seeing. There is no guest network setting in my airport utility.

    How can I delete the guest network from my airport. It was not showing up until I recently upgraded the airport. It now says my name's guest network and I don't like my name showing on the available network list! I am using a Verizon wireless modem with the wireless feature off.

    Open AirPort Utility, go to the Wireless tab and remove the check from the guest network check box.

  • How do I delete old wifi networks from appearing in the wifi icon in the menu bar.

    Just bought a new Airport Time Capsule and is up and running OK.
    When I click on the wifi icon in the menu bar all my old wifi networks appear 
    which are then viewable by neighbours although the networks themselves are PW protected.
    In system preferences>network>advanced I have deleted all my old N/Works allowing only
    my new one to appear.
    How can I delete the old networks I no longer use from re-appearing in the list under the wifi icon?
    Alan

    When you delete old networks in System Preferences > Network > WiFi > Advanced, be sure to click the OK button, then click the Apply button in the next window that appears.
    You also need to delete the old networks in KeyChain Access as follows:
    Open Macintosh HD > Applications > Utilities > KeyChain Access
    Click on the name of an old wireless network to highlight it
    Click the Delete key on your Mac
    Do the same for other old wireless networks that you no longer use, then restart your Mac.

  • How do I disable a wireless network and recreate it?

    How do I disable a wireless network and recreate it?  I believe I set it up incorrectly so I would like to delete it or disable it and recreate the wifi network

    Go into settings>network, highlight the network you want to delete, and click - at the bottom of the services list. You can then add it from scratch by clicking on +.

  • How can i access my wireless network?

    how can i access my wireless network at home?

    Does your iPad see your WiFi network - Settings>WiFi>Tap your network name, enter your password and tap join.
    If the iPad isn't seeing the network, try rebooting the router - unplug it for about 30 seconds and then plug it in again.

  • How can i delete a wifi network?

    how can i delete a wifi network?

    deroco wrote:
    Thank you but I tried that and it still shows up as a network. I live out in the country and shouldn't have any other networks close. I am afraid of a security breach.
    As far as networks showing up when you right click the WiFi icon in the Menu Bar, you will always see those that are close by. I know of no way to hide or remove those.
    What leroydouglas provided is correct to remove any WiFi networks you have previously connected to.

  • I have setup wireless at home but when I travel how do I find another wireless network?

    I have setup wireless at home, but when I travel, how do I find another wireless network?

    Depends on where you are. Most all hotels/motels have wireless. There are Internet cafes, libraries, Starbucks, and many other places providing WiFi service.
    In your iPad's Network settings you will usually find displayed all detected wireless systems. Not all of them may be usable unless they provide free access or you have a paid access membership. You should find this discussed in the user manual:
    Please Get the iPad User Manual for iOS 5

  • How to i find my wireless network password?

    how do i find my wireless network password?  I cannot log my i phone onto my wireless network.

    Please check out the following AirPort User Tip.

  • How to connect non-Apple wireless networks?

    Hello
    Before I start, I know very little about networking, so could do with some assistance please!
    In my office, I have a MacPro, fitted with an airport extreme. I also have a TL-WR1043ND Wireless N Gigabit Router, which I have connected to a ReadyNas NV+.
    In my house, I use my MacBook Pro connected wirelessly. The internet is accessed via a TP-Link TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router.
    Both the MacPro and the MacBook Pro connect to the internet cia the TD-W8961ND. The TL-WR1043ND resides on a separate wireless network. The idea is that I can access and store data wirelessly using the ReadyNas (which incidentally has become an issue since upgrading to Lion).
    The NAS needs to be kept in my office so it is secure and there is no direct telephone link to the office.
    Cutting a long story short, I'd like to make the two networks into one, so I was wondering if I could use the TL-WR1043ND as some sort of wireless access point (connected to the NAS) and joining it to the wireless network of the W8961 ADSL2 router.
    I don't know how to do this, so was wondering if somebody could help and perhaps guide me through some of the settings? I've searched the interweb abyss, without any joy.
    All the best
    Hoffmeister

    As you can imagine, this forum is primarily for assistance with Apple networking so it may be a bit difficult to really be able to provide you with a step-by-step on how to configure both of these routers for Wireless Distribution System (WDS).
    I did a bit of research and found the following TP-Link Support article that describes how to do this with a pair of their TD-W8960N routers and it may be worth reviewing to see if it can help you with yours.

  • How to block one of wireless network

    Hi there,
    I have Airport Extreme with 2 wireless networks, one for my iMac and my wife’s iPad another one is for kids PCs. All of us are connected only wireless.
    Question, how shall I block the kids network my configuration, now when I block the Airport (Turn Off Airport) actually it’s only me who cannot use wireless network, all others still can do it. Purpose is to block the kids using the wireless network during the night. Now my solution is to pull out lan cable between Airport and ADSL modem.
    I believe there must be smarter way to do it, I just don’t know how. Could you please help,
    thanks

    Hello!
    Your Extreme can set time restrictions on when specific computers can access the network. You can configure them using AirPort Utility:
    Open AirPort Utility, select your Extreme in the sidebar, and press "Manual Setup." If you're asked for a password, enter it. Go to the "Access Control" tab and set "MAC Address Access Control" to "Timed Access."
    Now you can set up the time restrictions.
    To add a computer to the list, press the "+" button. You'll be presented with a dialog that will let you configure the time restrictions. You'll need to enter the device's MAC address. You'll also want to enter a description so that you'll know what device the restriction applies to.
    You can double-click the "(default)" entry to set restrictions on computers not on your list. When you're finished, press "Update" and allow your Extreme to restart.

  • How can I remove old wireless networks as a choice on my iphone?

    I just picked up a new time capsule and i'm using my old time capsule to backup just one mac, just not wirelessly.  I need the rest of the Macs and Iphones in the house to no longer default to the old time capsule.  How can I delete networks I no longer use?

    You're welcome.
    This link provides instructions.
    http://kb.mit.edu/confluence/display/istcontrib/Mac+OS+X+-+Remove+Preferred+Wire less+Networks

  • How can I extend a wireless network with my AirPort Extreme Base Station?

    Today I purchased a brand new, dual-band base station to replace my Belkin N router, as I have had a handful of firewall, coverage, and other networking problems in my house lately. First off, I really like this router and it was very easy to setup. My MacBook Pro could use both bands and established a 300 Mbit/s link very quickly. After tweaking various settings to my liking, I was also able to maximize the connections on many of my non-Apple machines and devices. I noticed that the range of its network was better than my Belkin's, but unfortunately, it failed to completely saturate the area sufficiently. Since the Belkin still works well enough, I was hoping I could bridge them together one way or the other.
    The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct? I would like to place them at opposite ends of my home so I can get strong WiFi signals everywhere inside. However, when I try to get the base station to connect to my preexisting WiFi connection, it tells me that I can't extend the network and fails to join.
    So is this possible? And if it is, how would I go about setting it up? I know it would probably be easier if I had a simple range booster such as an AirPort Express, but I didn't buy one while I was at Fry's since I hoped I could make use of the older Belkin. This is its product page, if needed. Thanks for any suggestions.
    -MacUser

    The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct?
    Sorry, but no. The AirPort Extreme Base Station cannot "join" a network like the AirPort Express or Time Capsule, but you wouldn't want to do this anyway because in this configuration these devices will only perform as wireless clients ... not routers.
    Instead, the AirPort Extreme can either be extended or can extend another 802.11g or 802.11n AirPort ... or a very very few non-AirPort devices.
    One option for your Belkin would be to connect it to the AirPort Extreme by Ethernet but this may not meet your requirements or be a desirable situation. Otherwise, you would need to get another AirPort to extend your current one.

  • How do I extend a wireless network from one Airport Express to another?

    I have an Airport Express in my living room, wired into my router and it's currently outputting a wifi signal.
    I just got another Airport Express, and I've plugged it into my kitchen.
    How do I use Airport Extreme Admin Utility to see the other Airport Express (which currently has a solid orange light), and label it as "Kitchen", so that I can have music playing in my kitchen as well?
    I really don't want to have to wire an Ethernet cable all the way to the kitchen so that it picks it up, because I don't have room for that sort of hook up on my router.
    Is this possible.. and if so.. could someone kindly, please, write me a step by step tutorial as to how to add my "kitchen" to the wireless network.
    Thank you.

    Try temporarily connecting via Ethernet to the AirPort Express (AX). After you configure the AX you can disconnect the Ethernet connection.

Maybe you are looking for

  • C855-S5190 restored via recovery to factory defaults, ran the Toshiba updater, no Windows Update

    I'm desperately searching for help!  My elderly father has a C855-S5190 and after trying the update to Windows 8.1 from the store, the laptop doesn't boot all the way up - kept giving various errors.  So, he dropped if off for me to try to fix.  I co

  • Windows 7 x64 - iPhone and iTouch - iTunes Sync errors on new HP Dv8

    PROBLEM DESCRIPTION: I just purchased a brand new HP dv8 laptop and cannot get my iphone or itouch synch. I get errors for both the iphone and itouch, but my Nano and shuffle are fine. HP support said that this is a known issue and that the software

  • Reading the DAX query plan of a trace against a query on a Tabular model

    Hi, I'm monitoring a Tabular model queried by an Excel workbook. Inside SQL Profiler I've choosen as events the VertiPaq SE Query End, the Query End and the DAX Query Plan. But this last event isn't more readable. How can I read the info collected in

  • Query descritpion in PDF

    Hi I am new to WAD. I copied the existing version of standard 0ANALYSIS_PATTER TO ZANALYSIS_PATTERN and made this as a standard template. Now i copied ZANALYSIS_PATTERN to TESTTEMPLATE and assigned my dataprovider and executed the template. Now I can

  • Listening for an action on another GUI

    Hello :) I have written a GUI that sits on top of a security framework for use by developers wishing to gain a database connection for their applications. The login system is instantiated by a factory method which returns an instance of the login pro