How do I end an application that will not close

I downloaded Citrix Receiver to my Macbook Pro. Went to try and log on to my work address, the application just keeps spinning and will not let me cancel or close. the red button has disappeared. I even uninstalled the app and I still cannot close or make it go away.

That's OK it take some time if your not a computer junky.
Good Luck, Best Wishes and I'm glad I could help.

Similar Messages

How can I end a popup that will not let me close it?

I have a popup that says "pcteckers.com" continuing to pop-up. There is no visible way for me to close it. it prompts me to call an 877 number and give a code to get it to go away. It has completely taken over safari and I cannot do anything at all with safari except open it, be annoyed by the popup, and shut down the whole app. Please help!

Launch Safari with the Shift key held down. If that doesn't work, disconnect the computer from the Internet.
(116363)

How do I build an application that will run without being installed?

I have seen some of the prior posts on trying to do this, but most of them were older, so I'll ask:
Using 7.1, how do I build an application that will run without having to install the runtime engine? I have a client that wants to run serial port monitoring VIs to watch some custom hardware we built for him. His IT dept. won't let him install anything. If I could make this VI run off of a USB thumb drive without needing anything installed on the system it would be ideal. Space is not a problem, so I could include any runtime files needed. Can anyone tell me how to do this?
Thanks

Under what operating system was it running under back in the 90's when it was working?
I think that starting with NT platforms (applies to 2000 and XP, but not 9x) the hardware abstraction layer (HAL) prevented direct I/O to serial ports. Serial port related code that ran fine on 3.x and 9x would not run under NT platforms without modification.
Just some food for thought, do not know if it applies to your situation.
Good Luck
~~~~~~~~~~~~~~~~~~~~~~~~~~
"It’s the questions that drive us.”
~~~~~~~~~~~~~~~~~~~~~~~~~~

TS1292 how to activat a itunes code that will not redem

how to activat a itunes code that will not redem

I was having the same problem with a card that I received as a gift. Finally, I realized that it's an APPLE gift card and not an iTunes gift card. They are different and one will not work for another. The Apple card is used for hardware, software, cases, headphones, etc that you can buy in store or online. The iTunes card can only be used for music, apps, videos purchased through iTunes.
But as long as it is in fact an iTunes card, the only other thing I've read about it not activating is to wait a few days and try it again. Sometimes it takes a while for the store where it was purchased from to send the activation info to Apple and read it as a valid code. I guess it doesn't happen instantaneously when scanned at the store.

My iphone 4 is locked on one application and will not close or turn off my phone please help!

my iphone 4 is locked on one application and will not close or turn off my phone please help!

If you mean that the iphone froze in some random app you have ....the solution is easy .
Press and hold both Home Button and On/OFF button for about 15 seconds . The device should turn off and on again .
If not than please wait until the battery goes out and try the above step again whilst device is off .
Hope it helps

How to make a Java application that will change the client box's IP address

HI how to make a Java application( that application would be run on the client ) that will change the client box's IP address ( IP address of itself )

If you can do that through the command line, then use Runtime.getRuntime().exec(...) to execute your command.

How to repair applications that will not start

I have programs that will not start on my iMac . I have never had one issue since purchased . Do I need to reinstall lion to resolve my issues?
Thank you in advance for your responses.

Check with this compatability table, check with the specs of the program, watch for the "for 10.5+" that doens't mean it will work for 10.6 or 10.7.
http://roaringapps.com/apps:table
Use the developers uninstaller if possible, if not consult on their site etc., what is the manual uninstall methods.
Some programs have to use a uninstaller.
Sometimes you can simply drag and drop the program from the Applicaitons folder to the trash and that will be that, others have other bits in the System/Library/Extension folder (dangerous!) that can be removed by hand IF you know what to look for.
Usually a program will have it's name or other id info in their files, one can use Easy Find to locate all these named files. However don't go deleting without backing up your data off the machine.
delete the wrong file and your Mac will refuse to boot up
I don't advise "app undelete" programs, they tend to make people think that the app undelete program knows the right files to undelete and it doesn't, it just does a simple name search.
Good Luck

How can I copy a webpage that will not let me highlight it, i.e. use the control c key strokes?

How can I take a picture of a webpage that will not let me use the control C copy command? In other words, on this particular website, I try to highlight a passage that I want to save and put in a document, but the highlighting will not work. I asked them about that, and they simply said they did not have that facility, but I think the issue is protecting their copyrighted material. I know there is some way to take a picture of the page, and then I can use my picture editing software to crop it and enlarge it.

Are you trying to take a "snapshot" in a PDF?
If the part of the page or PDF you want to capture is fully visible, you can use the Windows print screen function to capture it. Either use the Print Screen key to capture the entire monitor display, or Alt+Print Screen to capture the active window.
If you need to do this often, or if you want to save the snapshot straight to disk, or if you need more than fits in a single Windows screen shot, an add-on such as [https://addons.mozilla.org/en-us/firefox/addon/fireshot/ Fireshot] can be handy.

How to fix a Domain file that will not open

We have a Domain file on our Mac Mini that will not open - iWeb keeps saying that it cannot be found, even though it is in the Library/Application Support/iWeb folder. I transferred the Domain file to my GS, and I get the same response - if I switch back to the original Domain file (on the G5), all is well. Obviously, the Domain file from the Mac Mini has gotten corrupted, but cannot determine the exact problem (though I think it may be the index.xml.gz file). I've reinstalled iWeb, checked permissions, deleted (and re-created) the associated plist files - nothing. Unfortunately, our company's web pages are in that Domain file, and cannot perform some much-needed updates. Any help that can be offered would be most appreciated!!

Have you tried double-clicking on the Domain file?

My ipad2 will not connect to my wifi and now i have a download that will not close or allow me to use other apps or shut the ipad off what can I do?

I bought the ipad 2 about a month ago now and have tried to connect my wifi and it says I cannot join my wifi. Now I have two pop ups for downloads that will not allow me to open apps or shut the ipad off. What should I do?

Hi,
For all people struggling with connecting their iPad to their router, constantly getting 'Incorrect Password' even though you have entered the correct one - this may be your solution as it just resolved my issue.
In your router settings online (usually found at 198.168.1.1) change your security from WPA2 or WEP to WPA. For my iPad it for some reason only accepts WPA but now it is running without problems. Let me know if this helps.
Cheers.

Remove damaged app that will not close?

printer Pro desktop will not close, can't delete because it's open. Cannot open because it's damaged. How do I remove ir?

I am going to assume you are referring to an iMac running OS X because this is the iMac forum. There are three methods to remove apps.
1. Use the developers recommended method, i.e. contac the developer and request their adive.
2. Use a third party app such as AppCleaner (Google it).
3. Drag the app to the trash.

HT6114 I am trying to upgrade to Mavericks from 10.6.8. When it tells me to close all applications, Safari will not close and I cannot proceed. What to do?

I am trying to upgrade to Mavericks from 10.6.8. It tells me to close all open applications. However, Safari will not close and the installation cannot proceed. Any suggestions?

Either try to force quit Safari (press Command + Option + Escape keys and then choose force quit in the pop up window), or, you can also shut down the computer. Then boot up and open the app store application to download Mavericks - you don't need Safari for it.

How to resolve a Lenovo PC that will not pass the Lenovo Splash screen with no access to Windows

Here is my problem and here is the solution!!!
My B540 Ideacentre would not pass the Lenovo splash screen. The only operational keys I had was F1 (BIOS) and F12 (BIOS options). F2 went to a light blue screen so no chance of even a one key recovery. Warrenty had expired four and a half months ago. I contacted Lenovo and after the guy told me to try F2 twice he said it was a HDD or other hardware failure and would cost around £200 maybe and also would take about two weeks.
AT THIS POINT YOU SHOULD NOT BE ANGRY FRUSTRATED OR PANIC. REMAIN CALM AND STOP AND THINK WHAT ACTUALLY WAS HAPPENING WHEN YOU LAST USED YOUR PC.
For me I remembered Windows had auto downloaded 8.1 and was asking me to install. Also my keyboard had lost shift W T Y keys. This told me that it was not a hardware issue but a software issue and perhaps from this update. My HDD was not clicking or beeping and this PC has a 2TB Seagate Barracuda which has a good reputation. Luckly for me I also have a Seagate external expansion 2TB and a 500MB expansion which was the HDD from my old HP Touchsmart which I converted into an external hard drive by buying a HDD enclosure with cooling fan and all leads from eBay for £25 and this is where the solution is.
If you can create an expansion drive so easily and access the HDD then why cant I do it with the HDD from my Ideacentre and of course you can. So first unplug your PC or laptop. Next remove the cover and unclip the HDD (which is easy with the B540. See user instructions). Next I removed my HP HDD from the enclosure and fitted my Ideacentre HDD in its place. Next you need a laptop or another PC. Switch it on and then connect your HDD to the laptop or PC via highspeed USB cable. My laptop is running Windows 7 Ultimate and of course has all the repair tools required. When the software has loaded you may get a box that will have two options. The first will ask you if you want to repair your files and the second to scan for bad sectors and to attempt repair recovery of sectors. Tick both boxes and click start. This is a long slow process but worth the wait. Nine hours later my HDD was ready. I connected my Seagate expansion to my laptop and moved all new files that I had not backed up. So at this point you should create a folder and move all your photos music videos documents etc to it. This can take upto three hours if you have never backed up before and are moving everything. Once completed I shut everything down and replaced the HDD into my Ideacentre. Make sure do not have any external devices connected such as expansions external drives headphones etc. Connect the power and switch on. The Ideacentre booted up and there was a pause at the splash screen then it went to a black screen and then by the miracle of logical thinking I was at my lock screen. I was never so glad to see the map of my home land "Ukraine". After jumping up and down with joy I then went in and all was as normal but to be sure I went into safemode and started a complete restore. This is the option where you completely format your HDD and restore as new. It takes a long time but it is the best option because you do not want this to happen again. When this has completed and you are in Windows do not wait a moment longer by playing with your photos or creating your desktop picture. Go to create a recovery drive (use a 32GB stick) and after that also make a copy to disc. Next go to command prompt (cmd) Admin and change a setting by typing bcdedit /set {default} bootmenupolicy legacy. This will now enable your F8 key to boot straight into safemode just incase you need to in the future. It will slow boot time a little but better to be able to get in to Windows than not at all for the sake of a few seconds.
Well I hope this helps someone out there and I know you may think its a lot to do but it is not. Ask a friend to borrow a laptop or PC and perhaps a HDD encloser. The rest is just time but when you see your lock screen you will not care trust me.
Cлава Україні!!! Героям слава!!!

I thought this was the method I used before but I followed through it and it was a horrific fail. "Operating system not found". Can anyone help?
http://superuser.com/questions/421402/how-to-create-a-bootable-usb-windows-os-us ing-mac-os-x
Steps To Achieve Victory
Download the ISO you want to use
Open Terminal (in /Applications/Utilities)
Convert .iso to .img using hdiutil:
hdiutil convert -format UDRW -o /path/to/target.img /path/to/source.iso
Rename if OS X gave it a .dmg ending:
mv /path/to/target.img.dmg path/to/target.img
Type diskutil to get a list of currently connected devices
Insert USB drive you want to use
Run diskutil again to see what your USB stick gets assigned eg - /dev/disk3
Run diskutil unmountDisk /dev/diskN (where N is the number assigned to your USB stick, in previous example it would be 3)
Run sudo dd if=/path/to/target.img of=/dev/diskN bs=1m (if you get an error, replace bs=1m with bs=1M
Run diskutil eject /dev/diskN and remove your USB stick
The USB stick will now be ready to use
Also similarly described here: http://www.tomshardware.co.uk/answers/id-1733410/creating-microsoft-bootable-usb -mountain-lion.html#.

How to store xml data fragments, that will not be queried?

Hello,
Delphi Client application communicates with Java Server application via XML messages. Client sends XML message over HTTP Post method. Java Servlet gets XML message, parses it, performs requested action (select/insert/update/delete), generates resulting response and sends it back to the Client.
I use Oracle DB XE 10.2.
For example: Client sends a request to the server, to append certain Order with new Product info:
Request:
<?xml version="1.0" encoding="UTF-8" ?>
- <Request OrderID="123123123" Action="NewProduct">
- <Product TempProdID="2" ProdName="L01" VisualID="1" Amount="1" TechClass="1" TechSubject="1" TechVersion="0" TechName="TestTech" ElemOk="0">
<Modified UserID="XXX" UserGroup="XXX" GroupLevel="0" />
- <QuickInfo>
<ProdIcon Format="PNG"
Encoding="Base64">iVBORw0KGgoAAAANSUhEUgAAAEAAAABACAIAAAA
lC+aJAAAAA3RSTlP////6yOLMAAAAvElEQVR42u3aQQ6EIAwAQP7/afe0
mo1mBVur0emJgwGmRDFNWwvH9I153OpjyoisefqXW3afm4WypP+MgomvT
z8AAAAAAAAAAAAAAMAzAClzAWQAdvexfqATEKmA/Fm0rYs5ozvoAWyWj4
ZqJ9efQKR8BJAHOPEdKAAc/lLdAhC/K68EBG+JWwAixfABgF8Jf6MAAAA
AAAAAAAAAAAAALwRUGgAAAAAAsgGJ3cfVrcfFl2jiIZzV+V7Zd/8BOtNi
0MnJ58oAAAAASUVORK5CYII=
</ProdIcon>
<Parameters />
</QuickInfo>
- <TechProduct CurVer="1" MinVer="1" TotalItems="330" ItemNodeSize="55074">
- <SubItem Class="TPlGraph" BindID="00B9C004">
<PropList />
- <SubItem Ident="Profiles" Class="TProfileList" Child="1" BindID="0188598C">
<PropList />
- <SubItem Class="TPlProfile" Child="1" BindID="018CA6CC">
- <PropList>
<Property PropIdent="ProfBaze0X" ValText="0" />
<Property PropIdent="ProfBaze0Y" ValText="990" />
<Property PropIdent="ProfBaze1X" ValText="990" />
<Property PropIdent="ProfHier0" ValText="0" />
- <Property PropIdent="InBorder" ValIdent="None" ValText="Nėra">
<ExtValue ColIdent="ItemCode" Value="None" />
<ExtValue ColIdent="Type" Value="" />
<ExtValue ColIdent="Filter" Value="" />
<ExtValue ColIdent="Width" Value="0" />
<ExtValue ColIdent="TechCall" Value="" />
</Property>
</PropList>
</SubItem>
</SubItem>
</SubItem>
</TechProduct>
</Product>
</Request>
I use DOM parsers to parse the received requests, extract certain info and insert it into relational tables using standart SQL queries.
My question is: what is the best way to store XML data fragments, that are not required to be saved relationally? I need to save the content of node <TechProduct> from the above example to relational table's column. There will be no need to query this column, no need to use relational views. I will use it only when Client application will request to modify certain order's product. Then I will have to send back the same <TechProduct> node via XML response.
So what column type do I have to use? CLOB? XMLType? Is it better to use object types? Do I have to register XML Schema for better performance? The size of the fragment can be ~2MB.
Thanks for your help
Message was edited by:
Kichas

Thank you for reply,
As you suggested, I will use XMLType storage as CLOB (without XML Schema).
As I mentioned before, I use Java Servlet, deployed on Tomcat WebServer, to receive XML messages from Client application via HTTP POST method.
I use these libs to get the XML payload and parse it into a Document:
import org.w3c.dom.*;
import org.xml.sax.InputSource;
import javax.xml.parsers.DocumentBuilderFactory;
import javax.xml.parsers.DocumentBuilder;
And here is the code:
public void doPost(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException {
try {
// get the XML payload and parse it into a Document
DocumentBuilderFactory docBuilderFactory = DocumentBuilderFactory.newInstance();
DocumentBuilder docBuilder = docBuilderFactory.newDocumentBuilder();
Document dom;
InputSource input = new InputSource(request.getInputStream());
dom = docBuilder.parse(input);
catch(Exception ex) {
System.out.println("Exception thrown in XmlService");
ex.printStackTrace();
throw new ServletException(ex);
I create a relational table, that contains XMLType column:
CREATE TABLE xwarehouses (
warehouse_id NUMBER,
warehouse_spec XMLTYPE)
XMLTYPE warehouse_spec STORE AS CLOB;
Now I want to insert all DOM Document into XMLType column. So I do like this:
import oracle.xdb.XMLType;
String SQLTEXT = "INSERT INTO XWAREHOUSES (WAREHOUSE_ID, WAREHOUSE_SPEC) VALUES (?, ?)";
XMLType xml = XMLType.createXML(con,dom);
PreparedStatement sqlStatement = con.prepareStatement(SQLTEXT);
sqlStatement.setInt(1,2);
sqlStatement.setObject(2,xml);
sqlStatement.execute();
sqlStatement.close();
dom is the Document, that I got from HTTP Request input stream.
My servlet throws an exception:
java.lang.NoClassDefFoundError: oracle/xml/parser/v2/XMLParseException
at XmlService.GetMatListServiceHandler.processRequest(GetMatListServiceHandler.java:111)
at XmlService.XmlServiceHandler.handleRequest(XmlServiceHandler.java:43)
at XmlService.XmlServiceServlet.doPost(XmlServiceServlet.java:69)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:716)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:809)
why does he needs oracle.xml.parser.v2.XMLParseException? I don't use Oracle parser? Does this code line throws the exception (I am not able to debug my code, because I have not configured JDeveloper to be able to use Remote Debuging):
XMLType xml = XMLType.createXML(con,dom);
Does it reparses the given dom Document or what?. When I deploy xmlparserv2.jar to Tomcat, everything is ok, application inserts XML data into XMLType column.
Is there another way to insert the whole org.w3c.dom Document or Document fragment (that is already parsed) into XMLType column. Can you provide any sample code?
The Document may contain national symbols, so they should be correctly stored and then later retrieved.
Many thanks.

How to fix my iPhone keys that will not work

When I am using my iphone keyboard, the upper row Q thru P will not work. That is in verticle mode, when laid horizontally, the R will not work.
On the number keys, the 4 will not work. The comma key also does not work.
I was told that a software restore could cure this. Also, I tried to load the new version 7 software, hoping this might help. But the Accept option would not work when accepting the TERMS from Apple. It seems that only works in verticle so that whole row/area does not work.

RESET DEVICE
Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost).

How do I end an application that will not close

Similar Messages

Maybe you are looking for