How do I extend an existing wireless network using airport express?

Hi all,
I am trying to extend existing wireless network using airport express, my main router is Belkin

Unfortunately, Apple's "extend" feature is designed to only work with other Apple routers if you are trying to "extend" using wireless only.
It is extremely unlikely that this feature would work with a router from another manufacturer using wireless only.

Similar Messages

Connect to Existing Wireless Network Using Airport Express?

I would like to use my airport express to connect to an existing wireless network set up in my apartment. The wireless router (linksys) is set up in my roommate's room to his desktop. I have a printer in my room and would like to use the airport express to connect to this existing network so that my roommates and i can print wirelessly. I need to keep the printer in my room.
Is there a way to do this? Please advise.
Thanks.

Is the LinkSys a WRT54G? If so, you have two options. If not, only the first option below is available to you:
1. You can configure the Express to connect as a wireless client. You won't be able to connect wirelessly directly to the Express in this mode; you have to connect through the router.
2. With the proper firmware in the WRT54G, you can set up a Wireless Distribution System (WDS). In this configuration, not only can the Express be used for printing and AirTunes, but it will also extend the range of your wireless network.

How do I set up a wireless network using Airport Express

I know very little about networking but want to set up a home network so I can distribute my music in the home using iTunes and AirPort Express units. I am hoping to control the music using Remote on iPod touch. I do not have a network setup or anything. What are the step-by-steps?
Thanks.
Billy

http://www.apple.com/airportexpress/setup.html should get you going. The on screen instructions for the Airport Utility are very simple and easy to follow.
iFelix

How can I rename an established wireless network using airport extreme?

How can I rename an established wireless network using airport extreme?

Thanks for the info. On your Mac......
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the picture of the AirPort Extreme
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window that appears
Edit/backspace out the Wireless Network Name and type in a new name that you want to use
Click Update at the lower right of the window
Wait a full minute for the AirPort Extreme to restart
Close AirPort Utility
The new network that you named will use the same network password that you set up originally.

Extend existing wireless network with airport express..impossible?

I have tried to extend my existing wireless network with an airport express, but it seemd that I always need a ethernetcable...apple support insured me it is possible but the airport utility software only allows me to extend using a cable it seems....

Couple of thoughts here.......
The AirPort Express will only extend a wireless network if you have another Apple router providing the wireless network to be extended.
Is your "main" wireless router an Apple product? If yes, what model number do you have?
It would also help if we could get the model number of the AirPort Express. Some older versions are not capable of extending a wireless network.

Extending an existing wireless network using Time Capsule

I connected my Time Capsule via Ethernet cable to my network. I used the airport utility to extend my existing wireless network (Cisco router)k. After that my wireless devices were disconnected and I got a message stating "Unable to join wireless network". The macbook that I used to set up the Time Capsule showed a message along the lines that a device on the network was trying to use the macbook's IP address, I changed the macbooks IP address and then was able to connect my ipad and iphone to the wireless network but the connection was unusable as it was so slow. has anyone done this successfully and if so do you have nay advice

If you connect the TC to the network by ethernet you do not extend an existing networking.. indeed you cannot.. only works with apple routers and no ethernet.
You create a wireless network.. you can use roaming .. ie use the same wireless name and security settings as the existing Cisco router but you must set different channels.
If you need instructions in that setup what version airport utility are you using. I would strongly recommend a version 5.. it is so superior cf toyland v6.

How do I extend an existing wireless network with a 2nd time capsule? I want to tether them with a gigabit ethernet connection.

I am having trouble with extending a wireless network using 2 timecapsules (1 is 1 terrbyte hdd, the other has a 2TB HDD.) The first one is connected to the WAN (cable modem) and our LAN. I would like to connect the 2nd one to the ethernet LAN and have it 'rebroadcast' the 1st ones wireless n network in order to expand the overall range of the network. Your help is very much appreciated.

Suggest that you download and install the much more useful AirPort Utility 5.6 for Mac OS X Lion.
I assume that Time Capsule 1 is operating correctly at this time.
Open Macintosh HD > Applications > Utilities > AirPort Utility 5.6
Select Time Capsule 1 and click Manual Setup
Click the Wireless tab below the row of icons and make a note of each of the setttings on this Wireless page.
Make sure that the Ethernet cable is connected to the WAN "O" port on Time Capsule 2.
Open up AirPort Utility and select Time Capsule 2 and click Manual Setup
Click the Wireless tab below the icons and enter the exact same settings that you wrote down for Time Capsule 1
Click the Internet icon, then click the Internet Connection tab
Make sure that the settings look like this:
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Click Update and allow 25-30 seconds for Time Capsule 2 to restart to a green light
Very important......perform a power cycle of the entire network as follows:
Power off every device in any order that you wish
Wait a minute
Power up the modem and let it run for minute by itself
Power up Time Capsule 1 the same way
Power up Time Capsule 2 the same way
Continue starting devices one at a time the same way until the entire network is back up

How can I extend my wireless network using Airport Express and an Airport Extreme on BT Infinity?

I have BT Infinity and I am using the Time Capsule with Airport Extreme as my router. Working well (even on wireless). I want to extend the wireless network with an Airport Express, but I cannot work out the settings necessary in Airport Utility. I am using Mountain Lion 10.8.2 on a Mac Pro. Please help!

BT,
I've read several of your posts, thanks for taking the time to share your wealth of knowledge.
I'm in a situation similar to the one described by 'scoutusmaximus'. Seeking the flexibility of a standalone router, I finally upgraded my 4-yr old ATT DSL gateway (modem+router) to a Comcast standalone modem + the ASUS RT-AC66U: http://www.asus.com/Networks/Wireless_Routers/RTAC66U/
Typically, I stick with all things Apple but the ASUS router seemed fairly superior to the current-gen base station (on paper, anyway; time will tell when it comes to performance) so, for once, I jumped ship. My plan was to extend the ASUS wired/wireless network using my TimeCapsule and 2 Airport Expresses in bridge mode, however, a google search turned up several unhappy customers that claim those devices don't play well with non-Apple routers, especially when it comes to 'extending' a network.
Questions:
1. Can I successfully extend the wired/wireless network created by the ASUS router using the 3 airport devices listed above w/out negatively impacting performance? I'd rather have 1 wireless network as opposed to creating a new wireless network with the TC and then extending it with the AP Expresses... though I'd consider that option down the line if it came to that.
2. Will the LAN ports on the TimeCapsule remain functional?
Btw, my house is wired so, I can reach all 3 devices via ethernet cable coming off of a central, managed switch. Supposedly, you only lose the LAN ports on the TC if you extend wirelessly.
Any advice would be appreciated.

Joining an existing wireless network with airport express

Ok, am almost to the point of throwing my AX across the room
AM trying to join an existing wireless network, its from a 2Wire gateway
one of three things happen
it won't find the AX in the first place
it recognizes it, but i can't connect to it
it goes through the configuration and when it restarts the AX, it can't reconnect to either the router or the AX and it fails. if this happens i can't reconnect to my wireless network without deleting it and re-adding.
it doesn't show up in my available wireless networks at all
protected via WEP, and i have tried using all the security options.

The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.
Are you using MAC address access control in addition to WEP?
Turn off WEP and see if that makes a difference?
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
WEP is now considered not to be secure and therefore it is advised you use WPA.
"WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
iFelix

Setup for extending Sky wireless network using Airport Express or Time Cap

Hi,
Hi,
I have three Mac computers/laptops (iMac, MacBook Air and G4 PowerBook), all currently functioning via airport on a sky wireless network (Sky HD Sagem router) all backing up wirelessly to a Time Capsule 1TB which is also connected to the same wireless Sky network. At the top of my house signal strength is weak as you would expect. I would like to be able to extend the range of the sky routers signal which is on the ground floor (3 storey house). My original idea had been to setup a AirPort Express on the 2nd floor to extend the network, but I am unsure what steps I have to follow and whether I need to create a WDS network or not? I've seen some comments that say Sky & Apple hardware are not compatible and it's not possible to extend a Sky router/wireless network using a Apple Airport Express or Time Capsule. Can someone provide me with a step by step set of instructions on what I need to do to set this up? If a work around is required, again any advice would be very much appreciated!
Many thanks,
Eugene

Welcome to the discussions!
Sky and Apple products are not compatible for the purpose of extending your network using wireless only.
If you could connect an ethernet cable from your Sky router to the AirPort Express, or if it's not possible to run an ethernet cable...take a look at a pair of ethernet powerline adapters to accomplish the same task by using the AC wiring in your home to transmit the ethernet signal.
If you configure the AirPort Express to "create a wireless network", this would in effect, extend your network by adding an AirPort Express that would be configured with the exactly the same wireless network name, security settings and password as your Sky router. The AirPort Express would also need to be configured as a "bridge".
Post back if you need more details about something like this.

Extending my Linksys Wireless Network with AirPort Express

I would like to add an Airport Express to my wireless network to extend my wifi range and add AirPlay to my home theater system. Can Airport Express be used to extend my current wireless system that is not an Airport Extreme devise?
Also, by adding the Airport Express does this now limit the number of devices I can have on my wireless network to the 10 even if the Linksys supports 50?
Thanks for any advise...

Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your non-AirPort router can be extended wirelessly with the AirPort Express Base Station (AX).
The few that are known to work are:
another Airport Express Base Station
802.11g Airport Extreme Base Station (AEBS)
802.11n AirPort Extreme Base Station (AEBSn)
Linksys WRT54G or WRT54GS (not v5)
Belkin F5D7230-4 and F5D7231
BT Voyager 2091
Netgear WGR614 v6
Buffalo WGR-G54

Extending wireless network using airport express

Greets all,
I'm trying to extend a wireless network in a two-storey apartment using TC and Airport Extreme.
The current setup is based on a Netgear N300 wireless router, which works fine upstairs but the signal is too weak to be useful downstairs. I have at my disposal a first-gen Time Capsule (TC) and a couple of Airport Express (AE) stations as well. I'd like to be able to extend the wireless network downstairs but of course the AEs won't talk directly to the Netgear router, so I'm guessing I need to use the TC somehow.
So far I've tried using the TC in bridge mode as well as a separate network via ethernet from the Netgear router, both of which worked but didn't extend the range - nor did it allow me the option of extending the TC network. In fact, all the searching I've done hasn't unearthed a solution to extend a wireless network using TC where TC is not the primary router.
Any help appreciated. I'm sorry if I haven't included all the necessary info off the bat.
Airport Utility 6.3.1 installed.

They are necessarily in fairly close proximity to each other (due ethernet cable).
If the Netgear and TC are in close proximity to each other, there is really no reason to have both devices providing the same wireless signal......and a very real possibility that there will be wireless interference between the two products.
My suggestion and instructions assumed that the Time Capsule would be at least a few rooms away from the Netgear. If the close proximity setup does creates some issues, then it will be necessary to turn off the wireless function on the Netgear router.
Unfortunately, the older A1088 version of the Express cannot be used to extend the wireless network since it has no settings for that type of application.
Locate the A1264 about half way between the TC and the general area where you need more wireless coverage.
Power up the A1264 Express for a few minutes, then hold in the reset button on the device for 10 seconds and release. Allow a full minute to for the Express to restart to a slow, blinking amber light.
Open up AirPort Utility
Click Other WiFi Devices
Click on AirPort Express
The utility will open up automatically and take a minute to analyze the products, then suggest that the Express be configured to "extend" the TC network.
Enter a device name that you want to use for the Express and click Next
The utility will set up everything for you. When you see the message of Setup Complete, click Done.
That's it.

Extending an existing wireless network using an Airport Extreme (dual band 802.11n)

Hello,
I currenlty have a wireless network set up inside my apartment using a Linksys E1000 wifi router. I would like to extend the network into a second room using my airport extreme. However, I have tried to set up the airport extreme to extend a network and it tells me that it cannot extend my currently network. I have already restored my airport extreme to its factory settings (using the reset button on the back of the airport extreme) as I used to use the airport extreme as the main base station in my previous apartment.
Help please!

Unfortunately, Apple's "extend a wireless network" function was designed as a proprietary feature that only works with other Apple routers.
It would be extremely unlikely that it would work with a router from another manufacturer if you are trying to "extend" using wireless only.
Suggest that you use another Linksys "repeater" or "extender" to insure compatibility with your current router.

Extend Linksys WRT160N wireless network with Airport Express

First off, I'm a network simpleton, so please keep that in mind!
I've seen similar posts, but I'm not sure definitively if this is possible. Trying to extend the wireless network from a linksys wrt160N with the airport. Is this possible without a phd in network engineering? If so, are there step by step instructions someplace that can help me?
I really appreciate any direction!

Welcome to the discussions!
I'm assuming that you are trying to do this using wireless only.
Apple's "extend a wireless network" feature will only work if both the main router and extending device are Apple "n" devices. Unfortunately, this feature is not compatible with devices from other manufacturers.

Will extending a wireless network using airport express cause weaker signal?

Hoping someone can advise on the following please....
I have installed an Airport Express to extend my wireless network and have confirmed with Apple tech support that it's connected and configured properly. I'm using an Airport Extreme base station as a wireless router.
The AX does not seem to be extending the signal range at all, and since the setup the signal strenght from the Extreme base station seems to be at half previous strengh.
Has anyone experienced this please and, if so, what's the fix?
Any replies gratefully received.
Regards

Let's check the settings on your Express. Temporarily, move it to the same room or an adjacent room to the Extreme and power it back up.
Open AirPort Utility - select the Express - Click Manual Setup
Click the Wireless tab below the icons and make sure that your settings look like this:
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the Extreme wireless network
Check mark entered next to Allow wireless clients
Wireless Security = Same setting as the Extreme network
Wireless Password = Same password as the Extreme network
Confirm Password
Update to save settings, wait for green light.
Then move the Express another room or two further away from the Extreme....and restart both the Extreme and the Express. Then perform the BSSID test again.

How do I extend an existing wireless network using airport express?

Similar Messages

Maybe you are looking for