How do I extend my DSL network via ethernet between 2 Time Capsules?

I need specific, precise instructions. This is so frustrating!
My first time capsule is connected to my DSL modem, I have a long ethernet cable that goes from the first T.C to the second one. And then I have a hard drive plugged into the second T.C. I also need to send an ethernet cable to my remote computer from the second T.C.
Where do I plug the ethernet cables in the second T.C.? There are two types of ethernet ports on the T.C.
I'd REALLY appreciate any help!
Thanx a million!
Mark Brown

Plug the Ethernet cable into the WAN port (circle of dots icon) on TC #2.
Check to make sure that you have TC #2 configured in Bridge Mode:
Open AirPort Utility - click Manual Setup
Click the Internet icon
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Upate to save settings
Power down the entire network...all devices....order is not important
Start the modem first and let it run for 45-60 seconds by itself
Start TC #1 the same way
Start TC #2 the same way
Start other devices the same way
It should be a simple matter to connect a drive to the USB port of TC #2 and a computer using an Ethernet cable. Use any of the 3 LAN <-> ports on TC #2 for this.

Similar Messages

How can I extend the WiFi reach of my new Time Capsule 3TB in the best way?

Hi there,
I have installed the new Time Capsule 3TB version and I would like to know how I can extend the reach in my house in the best way.
Does it make sense to add an Airport Extreme via Wifi as well?
Thanks,
Rick

If you need more wireless signal coverage, the "best" way to do this is add another AirPort in the central area that needs more coverage and then, connect the AirPort back to the Time Capsule using a wired Ethernet connection.
This type of setup maintains full bandwidth on the network. The result is much better performance in the "remote" area where you need more signal coverage.
Is is possible to have the AirPort "extend" the signal from the Time Capsule wirelessly....but you might want to understand the upsides and downsides to doing it this way.
Upside.....you will have more wireless signal coverage.
Downside.....the AirPort can only "extend" the quality of signal that it receives via wireless. The signal will have already slowed considerably by the time that it reaches the AirPort....so the "extended" area gets a significantly slower signal than the main area.
If you decide to try the second approach via wireless extension....try for line-of-sight between the Time Capsule and AirPort to help minimize the signal loss that will occur.

How can i extend this wifi connection by using 3TB time capsule? I have a mac book pro i7

Hi, i have a wifi in my house connected to an adsl wifi modem with fibernet speed. I just bought a time capsule with 3 TB and installed it at home. However during the first installation i couldn't connect TC to my modem with ethernet cable due to the absence of the cable.
I would like ask if i can extend the wifi range of my network by connecting my TC to my modem without a cable after the first installation with cable is done?
If yes,
Could you please explain how to do it?
Thanks in advance.

No, there is no modem in the TC.. you must continue to use the existing modem.
That can be bridged if your ISP allows it, and use PPPoE client on the TC. It is then the main router of the network.
Sometimes that setup is not possible.. the ISP supplied modem will not bridge or the ISP doesn't use PPPoE as there are a number of different methods to connect.. but the TC only supports that one.
Otherwise just plug the TC into the existing modem router and use it in router bridge mode.. this is the simplest setup and easy to do.
Create a wireless network and you can then use the TC instead of the main router for wireless if you like.

How to tell IP address of network printer attached to Time Capsule?

Hi,
I just bought a 1TB Time Capsule today. I have a HP network printer and a Vista desktop attached to two of the Ethernet ports. In addition,I have an iMac and Macbook connected to the Time Capsule wirelessly. Everything is working fine except the printer. My Vista desktop can't find my printer. Is there anyway to find the IP address of the printer so that I can connect to it directly?
Regards,
Roderick

Am I correct in guessing that you have the Time Capsules WAN port connected to a router or modem?
If so who is giving out IP addresses (via DHCP)?
Usually there is a way to see what addresses have been assigned by asking the device making the assignment.
In my configuration it's no the TC but the router/modem and I can ask it to list the attached devices it has assigned IP addresses to.
I use the TC in bridge mode and haven't tried it as a DHCP server, but I suspect it will also show attached devices?
I assume also that the network printer worked fine in your previous network configuration?
So it might help to know a little more about what you have before the TC and how you changed it to include the TC.

How can i connect/disconnect PPPoe via Ethernet connected time capsule??

I connected the time capsule with Ethernet.
I set connect to PPPoe with "Manual" option.
I could easily control "Connect/disconnect" pppoe using AIRPORT (in the menu bar). But I could not find a way to "Connect/disconnect" via ETHERNET. (No ETHERNET icon on menu bar anyway...)
Could somebody help? THanks a lot.

Have you consulted the printer's user manual for setting it up as an Ethernet printer? You will also need to delete your current printer in Print & Fax and when you Add the printer you will need to do so as an Ethernet printer. This means you will add it either as an IP printer using either LPR or IPP protocol - depends on what the printer supports. An Ethernet device requires an IP address that is either manually configured on the device or derived if the device supports DHCP. If the former then the IP address you configure for the printer must be within the range of IP addresses used by your router (typically 10.0.1.2-10.0.1.199 for an AEBS/TC.) This should be covered in the printer's user manual.

Connecting Airport Express via Ethernet to Time Capsule - Lose Internet

I have a number of Airport Express units throughout my house that are all connected to speakers. There are 2 Airport Expresses that I want to hardwire (via eithernet) as they are too far away and I tend to get audio dropouts. I wired the one with no problem. When I plugged the other in - my internet went out completely. I confirmed its not an internet or provider issue - its something to do with the Time Capsule. I will check my Airport Utility and it will show everything out. When I unplug the second airport, reset the time capsule - all goes back to normal.
Any ideas on what the issue is? How I can fix? I need to hardwire this second airport to avoid the audio drops. Thanks in advance.

your best connection is going to be wired, hands down, so long as you have a Cat5e or Cat6 spec'd cable.
now the N is pretty fast, but if you have the original version TC, running in N only mode will be the best option because running in multi-mode actually slows the N speed down, not making it worth the upgrade to N.
If you have one of the "Dual Band" models then the issue mentioned above doesn't apply.

Time Machine backup via ethernet to Time Capsule

I need to replace my 5 year old FireWire hard disk. I'm considering a Time Capsule and would connect it to my main Mac via ethernet.
Will my iMac see the Time Capsule disk and mount it on the desktop? And can I use it for Time Machine backups when connected with ethernet (rather than AirPort)?
I assume Time Capsule will do the above, but would like to hear from users who's used it like this. Thanks!

I would have to disagree with Smokerz. I've had repeated problems backing up to my airdisk through my AEBS when my computer was connected via an ethernet cable. Backups would go fine for a week or so, then suddenly the DMG wouldn't mount. There was no way to successfully repair it, and I'd have to start over again.
I have several computers on my network, and they were all backing up just fine, except mine, which was connecting with a cable. The others were backing up wirelessly with no problems.
Finally, on a hunch, I disconnected my ethernet cable from my AEBS and opted for using my Airport card. It seemed silly since the computer is right next to the AEBS, but it has been working for nearly a month with no significant errors.
(Before someone asks, I did not have the Airport connection running simultaneously with the ethernet connection. I used only one at a time, and I had them correctly configured with good, working equipment.)
Message was edited by: fletchbiz

Extend Airport Extreme Network via Ethernet to Airport Express

I am trying to extend a gen 4 Airport Extreme by hardwiring ethernet to a 2nd gen Airport Express and will add a second Airport Express if I can get the first one to work. I have a large network with a 24 port switch and aiport utility 6.3.2 (most recent as of this date)
First question:
When expanding my network using the hardwired Airport Express can I name the new network anything I want or should it be exactly the same as the Extreme Network. I would prefer to name it differently so I can keep track of which network my devices are acturally joining but I will be happy simply to get this to work either way.
Second question:
After repeated attempts to configure my hardwired Aiport Extreme, I get the following yellow status error:
Yellow Internet Connetion
Yellow No DNS Servers
Yellow Conflicting DHCP Range
Observation:
Many of the suggestions here and the link posted in a previous post are not based upon the most recent Airport Untility software so that may contribute to my lack of success so far. I am using the most recent version.

Even though the express was hardwired to the extreme during the set up process it was choosing to "extend" the 5 ghz network which I have activated on my extreme. I assume this is okay. It seems to be. It offered me no other option during the set up.
Both 2.4 GHz and 5 GHz bands will be extended if the extending device supports dual bands.
I configured the express by plugging it directly into the LAN port of the Extreme. Once configure, I plugged the express into my 24 port switch. It worked.
That's a good way to do things. If the Express works when connected directly to the Extreme, and doesn't when you connect it elsewhere on the network, then you know that you have a wiring or switch issue somewhere.
I choose to keep the express network name and base station name the same as those on the extreme. They worked. Since I really want to keep track of which network I am logged into, I later changed both the network name and the base station name for the express and it seems to all work under the new names.
Either will work, as long as you don't mind logging on and off of networks to switch. Most users prefer to have one "big" network. Then, they can walk a laptop from one area to another, stay on the same network and the Mac will automatically switch to pick up the strongest signal from the closest access point.
I activated the 5 ghz on the newly configured and newly named express. It seems to work.
As it should.
While configuing the express I got the error message metioned above a couple times. I kept trying the same procdure with out changeing anything and eventually it worked.
I can't duplicate that issue, but glad that things worked after a few tries.
Since my AppleTV on the second floor has difficulties connecting with the extreme, I am thinking of plugging it in to the express directly. How do you feel about this? WOuld I be better off running another separate ethernet wire off the switch?
Always the best plan to connect any network devices using Ethernet if you can. The best networks are the ones with an Ethernet "backbone". You can connect the Apple TV to the Express or the switch, whichever is easier. Personally, I prefer to connect devices to a switch if possible just to keep things simpler and make any troubleshooting easier.
This whole system with an extreme, 3 expresses, 3 appletvs, 12-14 cameras, a 24 port switch and up to 50 devices on the network at one time (computers, phones, ipads, etc, etc) works reasonably well considering the demands I put on it.
That's quite a home network. Glad that things are working. I am sure that you notice better wireless performance now with the two AirPort Express devices wired into the Ethernet backbone.
If we could get more users to set up their networks this way, most of the complaints that we get about slow wireless, intermittent connections, etc would go away.
It's not easy to run the Ethernet cable for some users, but I have yet to hear from the first user who ever regretted doing it.

Extend airport extreme network via ethernet to airport express (special case)

This question has been asked many times on the forum, and answered many times, but I have a special case and would like to know if it can be made to work.
As you can see, the issue is that the LAN port of the Extreme is not connected back to the switch, I've only connected the WAN port of the Extreme to the switch. Therefore the express doesn't get an IP over the CAT5e cable coming from the switch, and will only extend wirelessly. The reason I don't make that connection is because the switch/modem is in the basement, the Extreme is on the second floor, the express is on the far side of the first floor, and I don't want to run another cable through the house.
First question is, can the given topology be made to work?
If the answer is no, then would it work to put an additional switch on the second floor like the following?
Thanks!

That is exactly what I am saying.
Remember, the modem has only one Internet IP address that it can deliver to a router. It is the router that assigns "local" IP addresses your other devices to "share" the Internet connection.
If you connect the Modem to the Switch, then it will be matter of chance as to which device......the AirPort Extreme or AirPort Express will get the valid IP address. The "other" AirPort will not be able to connect to the network.
Bottom line.....if you have a simple modem, as you have pictured, then it must connect directly to the WAN port on the "main" AirPort router. Something like this, for example:

Cannot connect devices using Extend Network via Ethernet

Hi
I have been going nuts with this issue, and cannot seem to find any solutions. PLEASE HELP!
I have an Airport Extreme (pretty new and all up to date) connected to my modem. Everything works perfectly. The wi-fi is great, all devices can connect without any issues so nothing is wrong here. The Airport extreme is dishing out the IP addresses etc. The Airport extreme is in the lounge.
I purchased a new airport express yesterday. I put it in my study, far away from the lounge. I connected the airport extreme to the airport express using an ethernet cable. I plugged it in, and set it up to extend the wireless network via ethernet. I.e. it is set up in bridged mode and set up to 'create a wireless network' with identical name password etc. Everything is good. It reboots and the light is green. in the Airport utility everything shows up correctly.
Here is the problem., The second that any device (lets say iphone) moves from the lounge to the study, and tries to 'jump' to the stronger network provided by the express, it kills the ENTIRE network. The following happens:
1. The iphone loses wi-fi signal immediately. If I go into wi-fi settings, it sees my netwrok with FULL strength, but just remains in the 'spinning ball' state trying to connect. Seems to me that the express is unable to hand out an IP address or something.
2. If i open the airport utility on my Imac (in the study), the airport extreme has a yellow warning light and cannot be found via ethernet OR wi-fi. (The Imac is also Hard Wired from the Airport extreme in the lounge).
THe whole system requires a re-boot in order to work again.
If I re-boot the system, and leave a device near the airport express, it immediately receives signal, gets an IP address, and has an internet connection. Going back to the lounge causes no issues, it doesnt drop signal and still connects to the internet via the extreme. But as soon as I walk back into the study again - BOOM, everything drops.
I only purchased the new express because i was having EXACTLY the same issue with an older Airport extreme. No matter what I do, it just wont work via ethernet. I have tried all manner of settings. The ONLY setting that seems to work is to extend the wi-fi network. However, the rooms are too far apart, and this will require a third station in the middle, which i want to avoid (by the time the wifi network is extended across 3 decvices it is too slow).

Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try.

HT4259 how to configure extended network via ethernet

how to configure an extended network via ethernet

I assume that the Express is new, so that it still has the factory default settings.
Connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the AirPort Express
Power up the Extreme and Express if they are not already powered up
Open Macintosh HD > Applications > Utiltities > AirPort Utility
Click on the tab in the upper left hand corner of the window that reads Other AirPort Base Stations (1)
Click on the AirPort Express xxxxxx
Wait a minute or two while AirPort Utility analyzes the network and then announces that the Express will be configured to extend your network
Enter a name for the AirPort Express and click Next
Wait 2-3 minutes while AirPort Utility configures the Express and the Express restarts
When you see the message that setup is complete, click Done
That's it.

How can I make the 10/100BASE-T Ethernet port on my Airport Express work as a LAN-port? The AE is currently extending my network (generated by a Time Capsule)

Dear all.
I currently have a WIFI-network established by a Time Capsule. I want to use my Airport Express as WIFI-receiver for my Samsung TV. How do I pair them up so that the 10/100BASE-T ethernet port works as a LAN-port? I used to do it by setting it up as WDS but I understand this is not suitable for a "n" network.
Thx.

Under the wireless settings for the TIme Capsule, make sure that there is a check mark next to "Allow this network to be extended"
Then configure the AirPort Express to "Extend a wireless network". The Ethernet port on the Express is automatically enabled in this type of configuration and the AirPort Express will also provide more wireless coverage in the area where it is located.
See Apple's instructions in the link below. The iilustration shown in the support document shows an AirPort Extreme as the extending device, but the setup for the AirPort Express would be exactly the same
http://support.apple.com/kb/HT4259

Airport express won't extend network via ethernet but shows GREEN (HELP!!)

I have the following routers setup up the same network and are working.
10.0.1.1 Airport Extreme (connected to hardline from IP)
10.0.1.2 Time Capsule 1 (extending network and providing internet connection to computer via ethernet)
10.0.1.3 Time Capsule 2 (extending network and providing internet connection to Xbox1)
10.0.1.4 Airport Express 1 (extending network and providing internet connection to Xbox2)
Not working correctly
10.0.1.43 Airport Express 2 (wanting to set this router up to extend network to plug into desktop)
The router seems to join the network fine and will show GREEN but doesn't show a similar IP address as the rest of the routers. It also doesn't provide any internet connection via ethernet to any computer, the network pref page says that it shows RED and that nothing is connected to the computer for internet but airport shows GREEN.
Reset the router multiple times, tried every which way of setting it up and no go. I also tried assigning it a IP and not using DHCP and gave it a 10.0.1.5 and still the same outcome.
Right now just at complete loss as to what to try next.

Sorry, the older version of the Express does not have the option to "extend a wireless network", which is the setting on the new Express that provides more wireless coverage and also enables the Ethernet port.
What you want to do can be done with a different setting..."participate in a WDS network" on both the Time Capsule and Express, but I am not recommending that you do this because WDS operates only in "g" wireless mode. Your Time Capsule would lose most of its performance in this setting and the network would slow down tremendously...defintely not what you want for gaming.
You'll have the best performance if you connect the PS3 directly to one of the Ethernet ports on the Time Capsule using an Ethernet cable. If it is not possible to run the cable, the next best performance option would be to use a pair of Ethernet powerline adapters to send the Ethernet signal over the existing AC wiring in your home.

How do you extend the guest network on a time capsule to an apple express?

I have a time capsule in my main house with a password protected guest network i set up an apple express in the guest house to extend the networks. Unfortunately the guest house / apple express is only amplifying the main house network. I would like my tenant to join the guest network from apple express. Is that possible?
How do you extend the guest network on a time capsule to an apple express?

I would like my tenant to join the guest network from apple express. Is that possible?
Sorry, but Apple does not allow the Guest Network to be extended in any way.

Network mode: Create a wireless network vs. Extend wireless network via ethernet

Can some one tell me the difference between configuring AirPort Utility : Network mode: Create a wireless network vs. Extend wireless network via ethernet? I connect my cable modem to my Airport Time Capsule to a network switch via ethernet. The switch contacts to three Airport Express (AE connects to two Apple TVs via Ethernet) and another TC. Which is the best mode to configure my network?
Thanks

Create a wireless network is used only when the Airports have an Ethernet connection. If you are using the setup wizard.....the setting will read Extend using Ethernet during the setup. If you go back in using AirPort Utility to check the Network Mode setting.....you will see that it is really Create a wireless network.
Extend a wireless network is used only if an AirPort is connecting to another AirPort using wireless.......not Ethernet.
Every one of the Airports on your network must be configured to Create a wireless network.
If you do connect an Ethernet cable to an AirPort that is already set up to Extend a wireless network......that will create a massive feedback loop that will crash the network until you remove the Ethernet connection to the device.
The bottom line here might be if you are using the setup wizard, it will make the correct choice for you.

How do I extend my DSL network via ethernet between 2 Time Capsules?

Similar Messages

Maybe you are looking for