How do i extend my network with a airport express

How do I extend my network with mt airport express

Hi Tesserax, I'd like to join this discussion. It seems Jasonbeyer didn't reply, but I have a question related to his.
I'd like to extend the wireless signal from my Cisco Model DPC/EPC2202 VoIP Cable Modem (802.11n) to the living room where, at the moment, it is non-existent. I assume there's inteference or the signal cannot reach through the concrete walls and rooms leading up from my bedroom to the living room.
My question is:
I'm thinking of extending my wi-fi signal by using the Airport Express and simultaneously using it to connect to my hi-fi to play iTunes from my bedroom's iMac.
Something's telling me it's not going to be that easy. I'm using an iMac (7,1) if that's any help or clue.
What are the things I should take note of and will Airport Express be compatible with my modem? Would I have to get TWO Aiport Express to bridge the signal to my living room?
Thank you everyone for your time. Cheers!
Kane

Similar Messages

  • How do I extend a network with an AirPort Extreme from an Arris TG862?

    I'm using Comcast as my ISP, and after some issues with a previous Motorola modem, they supplied me with an Arris TG862 Router/Modem combo tower. I have two AirPort Extremes, one of which was previously connected to the old Motorola modem to send wireless into the house, but it only reached halfway, so I had the other AirPort Extreme in the middle of the house to "catch" the signal and then broadcast it out to the rest of the house. This worked fine for a while.
    But with the new TG862, it doesn't seem to be an option. From what I've read, if I have the TG862 in one room (connected to the cable), AirPort Extreme #1 in the middle of the house, trying to join the existing network (or extend it?), and AirPort Extreme #2 in the far end of the house (to extend from AirPort #1), it won't work. Apple's "extension" technology isn't compatible with all other modems or routers, and even if it was, I'd have to somehow configure the TG862 to "allow to be extended."
    So my question is, IF there is a desktop utilizing the TG862 as a direct connection (because it has no built-in Wi-Fi), is it possible to put the TG862 into bridge mode, connect one of the AirPort Extremes and have it act as the router so I can use AirPort Extreme #2 to extend that network out to the rest of the house? I want to ensure the desktop still has a connection, but there's Wi-Fi that actually goes out through the whole house.
    The connected-to-the-cable-desktop is a PC; we have multiple iPhones, iPads, and anywhere from 1 Mac laptop to 1 iMac in the house at any given time.

    pcbjr wrote:
    Topic title pretty well sums up the question.
    I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
    We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
    So, can the Extreme act as an "extender" only, in lieu of using an Express?
    Hiya.
    You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

  • Extending My network with three Airport Express or buy an Airport Extreme?

    I live in a large three story house and currently have it wirelessly networked using two Airport Express' but my signal is very weak on the third floor and in other spots throughout the house.
    Would it be possible to buy a third AE and extend the network that way or would I be better off buying a AEBS?
    Any thoughts or suggestions would be greatly appreciated.
    Thanks

    It will really depend on the construction materials used in your house or any other forms of Wi-Fi interference that could prevent a clear wireless signal. Both routes, you suggested, will have it advantages and disadvantages.
    Extending the existing network wirelessly using a WDS, effectively, cuts the throughput in half for each base station in the chain...so, in this case the second AirPort Express Base Station (AX) (acting as a WDS relay base station) would only get half that of the first AX (acting as the WDS main base station). In turn, the third AX (acting as the WDS remote base station) would receive half of the second's throughput. The good news is that you should have a strong signal across each of the AXs, just lower throughput the farther along in the chain.
    The 802.11n AirPort Extreme Base Station (AEBSn) has a greater range than either the older 802.11g version or the AXs. You may find that it will provide enough to cover you entire house. In the off-chance that it doesn't, you can still use it to create a WDS between AEBSn and your current AXs.

  • Extend wireless network with multiple airport express and netgear powerline

    I currently have the following network configuration:
    1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
    2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
    3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
    4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
    All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
    4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
    5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
    Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
    Thanks in advance!
    Dave

    I had a VERY similar problem:  I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule.  Every time I plugged in the wire to the TC, everything disappeared.  Unplugged, and boom.  Came back.
    Here's how I solved it:
    Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it.  Then, on the wireless tab select CREATE a wireless network.  But, give it the exact same name and password.  This is completely counter-intuitive.  You would think to choose EXTEND, but this would be wrong.  Next choose the network tab.  And, select Router mode to Bridge (off).
    By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
    See if this fixes your issue.  Fixed mine instantly.  AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out.  LOL

  • Extending a network with 2x Airport Express

    I tried searching and couldn't find any discussions which answered my question. We have a home office which was just completed (an actual, separate structure, not just a room) and I need to connect it to the main house where our Internet connection comes in. What I'm trying to do is use an Airport Express (802.11n), which wirelessly connects to the main router, an Airport Extreme (802.11n, 2nd gen.). This Airport Express is then connected via Cat5e cable and a gigabit switch (it's a pretty long run) to another Airport Express (802.11n). This second Airport Express will then reconvert the connection to wireless and allow us to connect our devices in the office to the rest of the network and get access to the Internet.
    Here's a crappy diagram I drew in Paint: http://i.imgur.com/5KrhX.png
    When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet. Once I try to commit the changes, though, the device restarts and ends up with a blinking orange light, disappearing entirely from the list of devices in Airport Utility.
    I've checked and the Airport Extreme is set up to allow devices to extend the network, and I've tried setting the first Airport Express to both "Join my wireless network" and "Extend my wireless network," though neither seems to make a difference.
    Am I missing something, or trying something that won't work? Any ideas?
    Thanks!

    When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet.
    You have two choices with AirPort Express #1:
    Configure the AX as a wireless Ethernet bridge. Apple calls this configuration a ProxySTA. In this configuration, the AX would join the wireless network provided by the AirPort Extreme, and then, share this connection out it Ethernet port to the Ethernet switch.
    Configure the AX to extend the wireless network of the AirPort Extreme. This would also enable the base station's Ethernet port.
    Of the two, I would recommend the first option.
    To configure the AX as a ProxySTA, you need just to make the following two setting changes:
    Wireless Mode = Join a wireless network
    Allow Ethernet clients (enabled)
    Both of these settings are on the Wireless tab in the AirPort Utility.

  • How can i extend my network using an airport express

    I have an airport express that connects wirelessly to an airport extreme.  I would like to use it to extend my network.  It has a strong signal coming in to it from my extreme.  It works fine when I try to connect to the network, but it dies completely when I try to use it to extend my network.  After going through a restart, it disappears from the network.  The only way to bring it back to life is to unplug it, let it rest a few seconds, plut it in again, and then reset it to Connect to the Network before it crashes again.
    I have a model of the express that is supposed to work with extending the network.
    Thanks for any suggestions.

    I would recommend that you configure your extended network by first placing the Express in the same room as the Extreme. Once the extended configuration is verified, you can take the Express to the desired location.
    The key to extending a wireless network with decent overall bandwidth performance is the proper placement of the extending base station. Please check out the following AirPort User Tip for details.

  • Extending wireless network with an aiport express

    I have a netgear wireless router set up in my house on the second floor, but my room being located on the first floor i get a poor signal so i bought an airport express to extend my network. i tried going through the aiport exress setup assistant but that wouldnt work, so i ended up hooking it to my netgear router on the second floor to set it up in airport admin utility and then brought it back down to the first floor. my itunes worked with the speakers for about.. ten seconds then stopped. and my signal is just as weak as before.. any suggestions?

    Unfortunately, it is simply not possible to use an Airport Express to wirelessly "extend" the wireless range of any model of Netgear wireless router. Netgear's wireless routers do not support Apple's implementation of a wireless distribution system (WDS), which is a necessary requirement for setting up an extended wireless network with the Airport Express. And no - it doesn't work the other way around either (Airport Express as base station, Netgear wireless router to "extend").
    It sounds like you did successfully configure your Airport Express to "join" your existing wireless network - which will allow you to print and stream iTunes to the Airport Express. The problems you are having with Airtunes "hanging" on your Mac are almost certainly due to the poor wireless signal quality problem that you are already aware of.

  • Trying to extend my airport extreme network with an airport express

    I´m trying to extent my network with an airport express 802.11g.
    I´ve been fallowing the guide:
    http://support.apple.com/kb/HT4259
    however, when I´m trying to configure the extended wifi base station ( point 8.)  it won´t let me choose "extend a wireless network".
    The only options I have is "create network", "join network" and "participate in a wds network".
    I´ve been trying to find a solution all day.
    Is there anyone out there who has hade the same problem or knows what it could be?
    I´ve made sure that my base station connected to the internet through ethernet has checked the "allow this network to be extended"

    however, when I´m trying to configure the extended wifi base station ( point 8.)  it won´t let me choose "extend a wireless network"
    Unfortunately, the older AirPort Express 802.11"g" model does not have a setting to "extend a wireless network", so it cannot be used the way that you want.
    The article that you reference should be clear about this:
    This article explains how to set up an 802.11"n" extended wireless network.
    You need to use one of the newer AirPort Express 802.11"n" models to gain the ability to "extend a wireless network".

  • I am unable to join my existing wireless network with new AirPort Express

    I am unable to join my existing wireless network with new AirPort Express.
    I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
    AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
    I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
    Any suggestions? Thanks in advance.

    Welcome to the discussion area!
    It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
    Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
    Power down the AX
    Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
    Release the reset button after 10 seconds
    When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
    Do you know the exact security type that your D-Link router is using? That is the key element in the process.
    Open AirPort utility, click Manual Setup
    Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
    Click the Wireless tab
    Wireless Mode....Join a wireless network
    Wireless Network Name...must exactly match your D-Link wireless network name
    Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
    Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
    Wireless Password...must match the D-Link network
    Click the Music icon to enable AirTunes
    Click Update to save settings
    Any luck?

  • Unable to create a wireless network with my airport express.  Please help!

    I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
    I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
    Any ideas? Thanks in advance for your help.
    Tom

    Is the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ...  or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?

  • Can I extend a network with an AirPort Extreme Base Station Rather than with an Express?

    Topic title pretty well sums up the question.
    I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
    We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
    So, can the Extreme act as an "extender" only, in lieu of using an Express?

    pcbjr wrote:
    Topic title pretty well sums up the question.
    I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
    We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
    So, can the Extreme act as an "extender" only, in lieu of using an Express?
    Hiya.
    You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

  • Creating and Extended Network with 2 Airport Express Units

    I had an extended network using 2 express units but one of them broke. The old network was setup with an older version of Airport Utility and I can't seem to repeat the set up a new network with the new express unit I have bought.
    The simple setup procedure using Airport Utility 5.5.1 only appears to allow you to 'join' the remote Express unit to an existing network, there is no 'extend remotely' option.
    I remember doing it last time by creating a WDS network which agrees with instructions I have found here - http://broadcast.oreilly.com/2009/03/taming-an-airport-express-wds.html
    I set up the first Express as a base station with a network and select 'Participate in a WDS network' and 'Allow this network to be extended' under the wireless tab. Under the WDS tab I 'Allow wireless clients' and add the hardware address of the second express unit.
    I then update the express unit but I get a WDS error which states, "This Airport wireless device is set up as part of a WDS network but no other AirPort wireless devices were found."
    This seems to be a chicken and egg situation.
    Any help would be appreciated.
    Alan

    Alan, welcome to the discussions!
    It appears that you want to set up a WDS arrangment, correct?
    But, I can't figure out whether you want to configure it with a "base" and two "remotes", or whether you want to configure it with a "base", "relay" and "remote"
    Can you clarify? I'll send you a link with instructions from forum expert user Tesserax with step by step instructions. Just need to know what set of instructions to send.

  • Extending an Airport Extreme (6th Gen) network with older Airport Express models

    I just purchased the latest Airport Extreme (6th Gen) base station to be my main wifi router.  I have two airport express models that I used in the past to extend my network with my (very) old retired Airport Extreme (2nd Gen): the 2nd Gen model A1264 (you plug into the wall directly) - I've had it for several years, and the newest 3rd Gen model A1362 (small square that lies on a desk or table) - I just purchaed a couple of months ago.
    My question is - will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)? 
    I don't have any AC capable clients yet - so everything is running on the "n" band - and the older Express is an "n" model, but I just have this (perhaps irrational) fear that attaching older routers will slow everything down.
    Any thoughts or suggestions?
    Thanks!

    will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)?
    The A1264 model will be able to extend only one band of the new dual band AirPort Extreme. Normally, the A1264 will extend the 2.4 GHz band since it is stronger than the 5 GHz signal.
    The A1392 will be able to extend both bands since it is also a dual band model, providing that it is located where it can receive a strong wireless signal from the new AirPort Extreme.
    Here, I am assuming that you are asking about extending wirelessly.
    You might want to keep in mind that extending wirelessly always involves compromises and loss of bandwidth. The main reason for this is that an extending device can only "extend" the quality of signal that it receives.
    The wireless signal from the new AirPort Exterme will slow down and lose strength the further that it moves away from the main AirPort. So, the extending device gets a slower, weaker signal to extend. The result is signficantly slower wireless performance in the extended areas.
    The way to solve this is connect the extending AirPorts to the main AirPort using a permanent wired Ethernet connection.  There is no signal loss in a wire, so the extending AirPort receives a full bandwidth signal to broadcast. The result is higher and more uniform speed on the entire network.

  • Trouble extending my WiFi network with older Airport Express

    Hi,
    As the question states, I have an older Airport Express which I have dug out to try and extend my WiFi network in a new house.
    I am on Virgin Media (fibre optic) in the UK and get a good WiFi service but one room in the house (which I have just turned into a cinema/media suite) has no reception.
    I have successfully managed to 'create a new network' via the Airport Express and the signal strength is 100% but for some reason if I try to reconfigure the device to extend the existing network I get no improvement at all from the (zero) signal I was receiving before.
    Am I doing something wrong? Or is there an additional step I am missing?
    I could live with having a secondary network but what I would really like to achieve is Home Sharing from my main computer, so that I can access my photos, movies and music etc. from iTunes on the big screen. If the computer exists on another network my iPad, iPhone and AppleTV can't see/use the media from that room.
    Many thanks in advance,
    Colin

    Are these the steps you used?
    To create a wireless extended network, you must place any extended Wi-Fi base stations within range of the primary Wi-Fi base station.
    Start with the device that will be configured as the primary Wi-Fi base station.  Then configure your extended Wi-Fi base stations, ensuring that each is within direct range of the primary Wi-Fi base station.The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
    If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.
    Configuring the primary Wi-Fi base station
    Power on all 802.11n Wi-Fi base stations and allow them time to appear in the AirPort Menu Extra.
    Open AirPort Utility (On a Mac, choose Go > Applications from your  desktop, click the Utilities folder, then open AirPort Utility. In  Microsoft Windows, choose Start > All Programs > AirPort to start  AirPort Utility).
    Select the primary Wi-Fi base station in the Base Station Chooser, then click Continue. Note: If you see a message appear that indicates that the Wi-Fi base station has been reset, click Cancel to continue.
    Click Manual Setup. Enter the base station password if necessary.
    Click AirPort in the toolbar.
    Click Wireless.
    Choose “Create a wireless network” from the Wireless Mode menu.
    Select the “Allow this network to be extended” checkbox.
    Enter a Wireless Network Name.
    Optional: By default, Wireless Security is set to None so that no password will be required to join the network. We recommend you click on the Wireless Security menu,  select WPA2 Personal, and create a password between 8 and 63 characters long.
    From the Radio Channel Selection menu, select Automatic.
    Click Update.
    The next window may indicate that there are some problems. Resolve the problems, then click Update.
    You are now ready to add extended Wi-Fi base stations to your network.
    Configuring an extended Wi-Fi base station
    Place any extended Wi-Fi base stations within range of the primary Wi-Fi base station
    Ensure that all 802.11n Wi-Fi base stations are powered on and allow them time to appear in the AirPort Menu Extra
    Open AirPort Utility (On a Mac, choose Go > Applications from your  desktop, click the Utilities folder, then open AirPort Utility. In  Microsoft Windows, choose Start > All Programs > AirPort to start  AirPort Utility).
    Select the Extended Wi-Fi base station in the Base Station Chooser, then click Continue. Note: If you see a message appear that indicates that the Wi-Fi base station has been reset, click Cancel to continue.
    Click Manual Setup. Enter the base station password if necessary.
    Click AirPort in the toolbar.
    Click Wireless.
    Choose “Extend a wireless network” from the Wireless Mode menu.
    Choose the network you want to extend from the Network Name menu.
    Enter the network and device password if necessary, then click Update.
    The next window may indicate that there are some problems. Resolve the problems, then click Update.

  • Extend wifi network via PLC + Airport express

    Hi everyone,
    I have a linksys WRT54G and an Airport Express. I'm using the WRT54G to create a wifi network (toto), and the AE is too far away to get the WR54G signal.
    I want to connect the WRT54G to the AE via PLC to extend the toto network, but when I try to select "extend a wireless network" in the airport utility, it says "the network you selected cant be extended..."
    Ideally I don't want do have 2 wifi networks... And I think WDS is not what I want to do.
    Do you know what settings do I have to use ?
    Many thanks !!!!!
    Message was edited by: dathieums

    Hello dathieums. Welcome to the Apple Discussions!
    The following are a few articles that you can find in both these Discussions and on the Internet where users have been successful extending the this Linksys wireless router with an AirPort Express Base Station (AX), that you may find helpful in configuring yours:
    o How to extend your Linksys WRT54G with AE
    o Linksys WRT54G and WDS
    o Extend a Linksys WRT54G network via AirPort Express
    o Linksys WRT54G, Airport Express, and WDS
    o AirTunes, AirPort Express, and the WRT54G

Maybe you are looking for