How do I extend my timeline?

My timeline only shows the first second of my compsition when the composition is 12 minutes, it just loops on the first second, I can see that my composition goes off of the timeline but cannot get the full view of the sequence, what do I do?

It sounds to me like jess just needs to know how to zoom in the Timeline panel:
http://helpx.adobe.com/after-effects/using/previewing.html#zoom_in_or_out_in_time_for_a_co mposition
Start here to learn After Effects: http://adobe.ly/AE_basics

Similar Messages

How do I extend the length of a photo in iMovie

I am trying to create a movie using only photos from iPhoto. How do I extend the viewing length of each photo? I have about 90 photos and I'm trying to do a 15-20 min. movie presentation. Right now, each photo only shows up for about 3 seconds. I want them to be on the screen for at least 5-10 before transitioning. Help!

several options:
• select the clip in the timeline of your Project
• drag'n pull the end of the clip to change its duration
or
• double-click the clip in the timeline of your project
• click on i (as info), upper right of screen
• change the numbers in the duration field
or
• select two7a few/all clips in the timeline of your project
• click on 'Adjust' (upper right of iMovies window)
• click on i (as info)
• change the numbers in the duration field

How do you change the timeline duration in Photoshop CC?

There seems to be 5 second limit on the duration of the timeline in Photoshop version 2014.
How can you extend the duration of the animation? There's a timeline window, but no "animation" window as mentioned in many of the help files.
How do you change the duration in Photoshop 2014?
I'm using Windows 8.1 as my OS.
Thanks.

Thanks for the reply, but my point was not about the lack of creating animations.
It seems that in Photoshop CC, you cannot change the duration of the timeline unless you click on the end of a clip and drag it out which will then give you more time. As the original post mentioned, you automatically get a 5 second duration unless you have a video clip that is of longer time. This all makes sense for videos, I understand that nobody (usually) wants to stretch video. Video by nature will extend the timeline based on how much footage is present.
Now take an animation scenario where you want to create something from scratch that spans longer than the default 5 seconds. There is no option!!! No document settings, nothing that will allow you to extend the timeline. I now have to click and drag each layer clip on the timeline to give it more time for the animation, one by one might I add (you can't even highlight multiple clips and extend them all at once, which is crazy).
So what does this mean? Well if you create a mockup of something with all of these intricate layers including backgrounds, copy etc. and you only intended to animate a certain piece for say 8 seconds, you'll have to extend each and every single layer clip in the timeline otherwise they will magically disappear and the only thing displaying is that which you have extended manually.
The reason why you need a document settings in the timeline is to prevent content from disappearing if something extends for a certain amount of time.
Frame by frame animations only allow for so much functionality, try to animate multiple objects at once with frames and go back and make a change to one part...
CS5 would simply show everything regardless if they did nothing on the timeline, it allowed you to see all of your elements present.
Again, I stand by my statement saying that the new timeline is flawed.

Extend the timeline by copy paste

I'd like to copy and paste a set of keyframes and frames at the end of the exisiting timeline... maybe several times to extend the timeline.
However I've been a bit flumoxed as to how a simple chore like that is done. It does not appear one can copy the frames, then set the cursor at the end and past the frames ahead of cursor,
Or do I have to create multiple layers to get the same effect by placeing them end to end down the timeline.
In the included screen shot, I'd like to copy/paste the frames on layer1 on down the time line but still on layer 1.
As you can see I've started using layers to create the same effect... but is that really the way to do it?

meglomor wrote:
click on frame 1 of layer one
hold down shift and click on the last frame in layer 1
(the entire span of tweens and keyframes will be selected)
release the mouse and shift
hold down pc:ALT mac: Option and click anywhere in the selected/highlighted tween span and drag the frames to the right.
this technique will work on multiple layers as well.
Ahhh cool. A little different than some applications but still sort of obvious now I see how its done.
Thanks

How do I extend my AirPort Extreme network using airport express

How do I extend my AirPort Extreme network using airport express

see http://support.apple.com/kb/HT4145 and other support articles
and/or
https://discussions.apple.com/thread/4462789?start=0&tstart=0
and many other discussions on this forum about this topic.

I get a neighbor's wifi on my MacBook in my bedroom. How can I extend the range to the MacMini in my living room?

I get a neighbor's wifi on my MacBook in my bedroom. How can I extend the range to the MacMini in my living room?

You can't. It's not your network.

How do i extend airplay to stream music at the same time to AEX and ATV2

I have a new ATV2 and an AEX, my macbook, 2 Ipod touches and an Ipad2.
I figured out how to setup my ATV2 and airplay through my macbook and my touches. My ATV2 is in my living room on a Yamaha 6.1 receiver with 2 channels. I have 6 speakers in my living room on channel A and a speaker in my bathroom on channel B.
So....I decided to grab an extra Bose speaker and bring it to my foyer/kitchen and hook it up to my AEX since i cant hear the music too well when im cooking or in my office from the speakers in the living room.
I setup the AEX to connect direct to the speaker. When Im on Itunes (either mac book or touch) i only get two options to airplay, AEX or ATV2.
My question: How do I extend airplay to stream music on BOTH AEX and ATV2 with the same music at the same time?
Please and thank you!

As you are already aware both the 802.11n AirPort Express Base Station (AXn) and ATV2 are AirPlay "speakers." When both devices are properly connected to your home's wireless or wired network, both should show up in iTunes as in your case. Also the iTunes AirPlay speaker selector should provide you with an option to choose multiple speakers. As a minimum, you should see: Computer, the AXn, the ATV2, and the Multiple Speakers options. Is this not the case?

How do i extend the bandwidth of my system

The control problem I am having is extending the bandwidth of a force control system. The system is used to apply mechanical load to bone to facilitate research into Osteoporosis. The following concisely describes the system and the different things I have tried to solve the problem,. I imagine it is quite lengthy compared to the usual questions but any advice you have to offer to a Mechanical engineer would be much appreciated.
System Description:
I am using Labview (with Flex motion) to program the NI 7344 motion control servo board (PID update rate of 62.4 micro-seconds). This output signal is then amplified by the MID 7654 power amplifier, supplying current to a Voice coil (this can be considered as a Linear DC motor with a bandwidth of 40Hz). This applies the force to a bone sample. Feedback is then provided by a load cell and connected to the ADC feedback channel of the servo board. (For full specs of all mentioned components please refer to the web links which are listed at the end of this email!)
Problem description:
After optimally tuning the PID characteristics and defining the amplitude and pre-load, I can successfully control a continuous, sinusoidally varying force (frequency 1Hz), however when I try to increase the frequency to 10Hz, the amplitude of the output waveform is marginally reduced�i.e. there is attenuation. I know that the bone sample is not viscoelastic enough to act as a low pass filter. The bandwidth of the Voice coil is not a limiting factor either, so�..
How do I extend the bandwidth of this system?
The following Paragraph describes some of the things I have tried, which have had some or no influence. Being a mechanical engineer I would be grateful for any expert advice.
(Note all results have been verified with an oscilloscope where applicable)
Influential Factors:
1) Method of programming.
To generate the wave form a series of points describing one period are written to a circular buffer on the servo board. The points are executed in 10 milli-second intervals and are splined through using a cubic spline algorithm (hence a period described by 100 points gives us a frequency of 1Hz and a 10 point wave gives us 10Hz). All this happens on the servo board in real time. I am confident that although the integrity of the sine wave is reduced at 10 Hz the amplitude is still described within the 10 points and so is not the reason for attenuation. However this does limit the maximum frequency achievable. (I would say the max frequency is about 20Hz)
2) Redefining the resolution of the of the ADC Feedback
The 12 bit ADC feedback channel is scanned at a rate of 50 micro seconds (faster than the loop update rate which is 62.4 micro-seconds). Initially the voltage range was specified at -/+ 10 V giving 20/(2^12) Volts per significant bit, however I noticed that when I increased the resolution to the max possible by changing the range to 0-5 V (giving 5/(2^12) volts per significant bit), the amount of attenuation was reduced, however there was still some attenuation there. This begs another question why would this factor improve the frequency response???
3) PID characteristics
The system gives an optimum step response when using only a pure integral term and setting Kp= 0, Kd= 0. It seems as though the fastest step response is limited to about 6 milli-seconds. The system is fine tuned and any slight increase in the integral term results in immediate instability. Therefore there is no scope to improve the system bandwidth by altering the PID characteristics.
Can you offer me any expert advice?
Considering this information, what would you advise? Do I need a board with a faster loop update rate ?, I have considered using Labview Real Time, which offers a board with a 26 KHz update rate as apposed to the 16Hz (62.4 micro-seconds) provided by the current board). Do I need to use different control algorithms as apposed to PID, if so which ones???
Any help or advice you have to offer would be much appreciated and could help in the battle against osteoporosis. Should you require more information or would like to speak to me send me an email and I can answer any further questions or give you a ring.
Regards Duncan Webster
Email: [email protected]
Product specs:
Servo board:
http://www.ni.com/pdf/products/us/4mo636-637.pdf
Power amp
http://www.ni.com/pdf/products/us/4mo642-643.pdf

Hi Duncan,
i'm sorry that this answer took this long, but i think a constructive answer which takes a long time is better than a useless answer in a short time....
For the following thought-provoking impulses we have to consider the signal-change when increasing the frequency. The points which describe the signal get streched over the period. Increasing the frequency enlarges the distance between the points.
a) The spline algorithm could be the problem here hence the signal does not correctly pass through the points anymore with increased frequency. Therefor the amplitude decreases with increased frequency. Perharps another kind of spline algorithm can be helpful.
b) Another point can be the control deviation. Since a feedback control system needs a devia
tion for the control, the deviation gets larger when increasing the frequency of the controlled loop. Maybe the control loop has to set the desired value when already getting to a new point. So the signal could get "washy" and the maximum amplitude is reduced.
In this case, the "Velocity Feedforward"-parameter could be of use. This parameter is to use with caution for it can have similar effects like a too high chosen integral term.
c) You can try to set the 7344 to circular contour. Therefor use 2 axis where you use the second axis as dummy (open step). There is a major disadvantage in this setup: since you use 2 axes at the same time, the 7344 can update each axis only with 125 microseconds. But perharps this is sufficient. Either way the parameter of the control loop have to be adapted (integral term reduced).
d) If the 125 microseconds describend in c) is insufficient, you can try to test it with a 7352. The 7352 can handle 2 axis at a time with a update rate of 62.5 microse
conds for each axis.
I hope this answer helps you in solving your rather special issue.
-Norbert
NI Germany
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

How to: Select a Specific Timeline Displayed in Project Online when having multiple timelines within the Enterprise Project

Currently I have an Enterprise Project which has 6 custom timelines and I want to know how to select a specific timeline to be displayed on the Project specific SharePoint site.
I'll provide some background for you so you understand my issues... I have created a "template" project with 6 custom timelines. From that project I created multiple new projects - which they all have the 6 custom timelines. These projects are
all stored in the Project Center. The problem I am having is I don't understand how to select a specific timeline to show on the project specific SharePoint site. They all seem to be displaying 1 of the 6 timelines (in no particular order). I was thinking
maybe if I had edited a project and saved it while it was displaying a specific timeline it would display the last selected timeline on the SharePoint site, but it doesn't seem to be doing that.
Is there a way to select a specific timeline to display on the SharePoint site? Also, is there a way for a user to cycle through the numerous timeline view on the project specific SharePoint site?
I await your help!! :)

Michelle_Sm --
I ran into this problem at the company where I used to work. One of our PMs had created multiple Timeline views, and wanted a specific custom Timeline view to show up in the Project Site for that project. I could not see any way to make that
happen. We had one of our SharePoint developers look into the issue, and he could not see any way to make this happen either. So, I am thinking this is not possible to do. But I would gladly welcome others in this forum to tell us the trick,
if there is one! :) Hope this helps.
Dale A. Howard [MVP]

How do you extend the guest network on a time capsule to an apple express?

I have a time capsule in my main house with a password protected guest network i set up an apple express in the guest house to extend the networks. Unfortunately the guest house / apple express is only amplifying the main house network. I would like my tenant to join the guest network from apple express. Is that possible?
How do you extend the guest network on a time capsule to an apple express?

I would like my tenant to join the guest network from apple express. Is that possible?
Sorry, but Apple does not allow the Guest Network to be extended in any way.

How do I extend my existent airport extreme network by addition of a 2nd airport extreme?

How do I extend my existent Airport Extreme network by addition of a 2nd Airport Extreme?

Can you clarify which version of the AirPort Extreme that you have now along with the model that you plan to use as the second device?
The older "round" AirPort Exteme or the newer "square" version with rounded corners?
Are you planning to extend using wireless only.....or by connecting the AirPort Extremes using a wired Ethernet connection?

How can i extend the Apple TV storage to get an 1 TB? apple has any external hard disk or similar?

how can i extend the Apple TV storage to get an 1 TB? apple has any external hard disk or similar?

Only AppleTV1 has an internal PATA drive. The largest PATA drive available is 250gb.
Hacks are available to use the USB port on AppleTV1 to access more storage.
AppleTV2 does not have an internal drive.
Why do you need more storage in your AppleTV? iTunes streams video to AppleTV so no need to store it locally.

How can I extend the range of my chart?

I've asked this question before on here, and found that shift-clicking for more cells has usually worked, but I have now run into a new problem...
My chart used to cover the range B5:P50. However, since moving a column it now only covers the cell range H5:P50. My chart is on a separate sheet. Usually if I want to add more to the range it will be downwards, so I just click on the chart, then click on the Main Sheet and shift-click to add more cells. Unfortunately, because the range I want is to the left of the highlighted area this time, I can't use shift-click.
How can I extend the range of my chart so it includes cells to the left of the currently selected range? In Excel I'd be able to just type the range in a box somewhere, rather than all this GUI-based clicking and dragging which is actually more difficult! Is there somewhere I can just type the range in that I want?
Thanks!

"I want to add some series that are missing from the chart. How do I do that?"
Here's a two step process to do that:
Select the chart to show the the data selection on the associated chart.
Click in the leftmost column of the data, and drag left to change (move) the selection (blue arrow) for the result below:
Grab the control handle (small circle) at the bottom right corner of the selection, and drag right, as indicated by the blue arrow.
Result shown below.
Reassign colours and do other formatting as desired.
Regards,
Barry

HT1689 How can I extend the number of times my phone rings before going to answerphone

How can I extend the number of times my Iphone 4s rings before it goes to answerphone

Call you carrier and ask them how you can change this. The number of rings before voicemail kicks in is set by your carrier. Some have the option to do it from your phone if you know the sequence of codes to send, but you need to ask your own carrier how to do it for their system.

I made a video series on one time line and now want to copy paste sections into other tiemlines so I can separate the series into distinct videos to upload. How do I get new timelines? When I go to new event it asks for import footage.

I made a video series on one time line and now want to copy paste sections into other tiemlines so I can separate the series into distinct videos to upload. How do I get new timelines? When I go to new event it asks for import footage.

You seem to be new to this software, so I highly recommend that you take some time to learn it using some great tutorials available online - it will pay off to invest the time, if you follow through, for example the great (and free) introductory tutorial at izzyvideo.com.
This is an amazing piece of software, and you'll have a lot to learn, but it's well worth it.

How do I extend my timeline?

Similar Messages

Maybe you are looking for