How do i find the internet MAC address for my MBP?

I am trying to get my MBP integrated into my home wireless network.  Need to enter MAC address.

System Preferences > Network, select the connection type (probably Wifi). Advanced button > hardware tab.
The MAC address is listed there.
MAC address filtering is not actually adding any security to a wifi network, so you may want to turn that off - it is trivial to spoof a MAC address & they are visible to anyone in range. Use WPA2 with a good password if you can.

Similar Messages

  • How do I find the valid IP address for the base station?

    I am trying to install he Airport Extreme but I am receiving this message:  The wi-fi base station does not have a valid IP address. How do I find the valid IP address for the base station?

    I have run an ethernet cable from the modem to my Mac and I do have internet connection. But when I connect that ethernet to the TC and run Airport Utility to set it up I get the error about no valid IP address.
    This tells us that the modem has associated with your computer. The modem "remembers" the settings for your computer and "looks" for it when you connect the TC. It does not "see" the computer, so it does not associate with the TC.
    The modem needs to be reset so that it will not remember the computer. Then it will associate with the next device that connects.
    Look for a reset button on the modem, and if present, push it for a second or two. Then power off the modem and leave it off for at least 30 minutes. Power off everything else as well.
    After the wait period, power up the modem and let it run for 4-5 minutes by itself. Then power up the TC and let it run a few minutes. Power up each other device one at a time about a minute apart.
    Check to see if the modem is now associating with the TC so that the TC will get a valid IP address.

  • How do i see the whole mac address for my iphone 5C?

    The Wi-Fi (MAC) address show in Setting>General>About only shows 4 pairs with ... after the 4th pair. How do I see the last two pairs? Touching the ... or anything else on the screen doesn't help.

    This is my friends iPhone and though I checked all of his settings I don't see anything turned on or checked that would make the fonts larger than normal.
    I checked this because my iPhone 6 doesn't have this problem.
    I was able to find a solution on another sight though. It was suggested that if the entire MAC address didn't show to just touch and hold the visible number until 'copy' shows. After copying the number just paste it into a text message field and the entire number then shows up. Viola!
    Its a shame that I had to spend so much time researching this to find it on a non-Apple sight to get this simple answer to a very frustrating glitch.

  • How to specify in the ISE mac-address with its description?

    Hello :-)
    I want to implement ISE 1.2.
    We have a database of mac-addresses and their description (for example the phone with the Mac address, John).
    When connecting the phone John to a wifi network, WLC checks its mac-address in the database and allows access.
    How to specify in the ISE Mac address with its description?
    In the endpoint settings in ISE 1.2 there is no description field. We have ISE1.2.1.198, vWLC 8.0.100, AIR-LAP1131, MS AD (Win2003).
    How can I handle this situation? Any ideas?

    This link http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/user_guide/ise_user_guide/ise_man_network_devices.html about managing network devices(router,switch), not endpoints(phone, notebook).

  • How do i find the ftp server address information in business catalyst, adobe technical support says

    how do i find the ftp server address information in business catalyst, adobe technical support says mine are wrong. I haven't changed nothing and it used to connect. someone please meassge me, not too sure how to use a forum and do not know how to get catalyst support.

    Hi Michael,
    I think you are referring to the changes switching from regular FTP to SSH connection which is now required. 
    Please review the article below covering this recent update and the changes needed to establish your connection via (DW or FTP client).
    - http://forums.adobe.com/docs/DOC-2841
    Kind regards,
    -Sidney

  • How to find the E-Mail address for my HP 6700? Printer shows E-Print connected.

    I got help on the board about getting a new printer code and the Home Printer page shows that it is on, but now I don't know how to find the E-Mail address for my computer -
    This question was solved.
    View Solution.

    Hi,
    From the printer Front panel, navigate to Setup. Locate and enter Web Services. Aprove any of the steps to enable the service... allow the device several minutes to complete the registration, a page will print automatically with the printer code and the directions to select the email address from hpeprint.com.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Hi, Dear. I purcahse my iphone 4S on of the guy, my problem is when i update any app from App store and i click update there is an e-mail address is coming which i doesnt know about the password, how can i revome the e-mail address for update our apps.

    Hi, Dear. I purcahse my iphone 4S on of the guy, my problem is when i update any app from App store and i click update there is an e-mail address is coming which i doesnt know about the password, how can i revome the e-mail address for update our apps.

    Yes. Delete the Apps that were not Purchased using Your Apple ID.
    But a Restore as New is the way to go.

  • How can I find the all path available for a MPLS VPN in SP network

    How can I find the all path available for a MPLS VPN in SP network between PE to PE and CE to CE?

    Hi There
    If we need to find all the available paths for a remote CE from a local PE it will depend upon whether its a RR or non-RR design. If the MP-iBGP deisgn is non-RR  the below vrf specific command
    sh ip bgp vpnv4 vrf "vrf_name"  will show us the MP-iBGP RT for that particular VPN. It will show us the next hop. Checking the route for same in the Global RT will show us the path(s) available for same ( load-balancing considered) .Then we can do a trace using the Local PE MP-iBGP loopback as source to remote PE's MP-iBGP loopback to get the physical Hops involved.
    However if the design is RR-based there might be complications involved when the RR is in the forwarding path ie we have NHS being set to RR-MP-iBGP loopback and the  trace using the Local PE MP-iBGP loopback as source to remote PE's MP-iBGP loopback will get us the physical Hops involved.
    If we have redundant RRs being used with NHS being set then the output of sh ip bgp vpnv4 vrf "vrf_name" will show us two different available paths for the remote CE destination but just one being used.
    RR-based design with no NHS being used will always to cater to single path for the remote CE detsination.
    So in any case the actual path used for the remote CE connectivity would be a single unless we are using load-balancing.
    Hope this helps you a bit on your requirement
    Thanks & Regards
    Vaibhava Varma

  • How do you find the iPad phone number for cellular data?

    How do you find the iPad phone number for cellular data?

    I know this post was a long time ago but people still seem to be viewing it.
    Quickest way:
    Via the iPad on 3G, go to http://m.telstra.com. The service number is then displayed and you are given the option to recharge.

  • How do I find the 'auto fil' feature for Firefox?

    how do I find the 'auto fil' feature for Firefox?

    Hi jasmtch,
    I am assuming you are talking about auto fill for forms and not password/logins, correct? If that is the case, just take a look at the Knowledge Base article [[Form autocomplete]]. This will give you all the information you need to use and manage the autocomplete feature.
    Hopefully this helps!

  • How do I change the RESCUE email address for my security questions, when I have forgot the security questions and answers?

    How do I change the RESCUE email address listed for my security questions to my Apple ID notification to change security questions? The current email for changing my security questions is no longer my email. And I forgot my security questions answers. What do I do?
    iPad 2, iOS 7.1

    There is no need to post multiple versions of your question, the answers will be the same,
    Please see your other thread.
    https://discussions.apple.com/thread/6078685?tstart=0

  • HT4061 How do I find the Device IMEI number for an iPad Mini?

    How do I find the Device IMEI number on an iPAD Mini?  It was not on the packaging or the back of the device.

    Settings > General > About

  • How do I find the dc load line for a BJT on multisim 11

    Im trying to find the dc load line for a BJT on multisim 11.

    Thanks for reply. Would please tell me the procedure to get output jfet characteristic curve by changing d-s voltage at different g-s voltage to drain current? I attached my document. It's better if you send me a sample simulation file if possilble. actually i will try for other jfet model once i know how to simulate it. it would be great help. thank you in advance.
    Attachments:
    expecting waveform.JPG ‏32 KB
    char.JPG ‏345 KB

  • How can I find the original newsfeed addresses in apple RSS mail

    I subscribe to a lot of newsfeeds through my apple mail RSS feed.  Now I want to find the original addresses to load onto a new device, but the apple mail only shows the title I gave the feed.  Where is the actual feed hidden (for example feedburner address)?

    Depends on whatr you mean
    Deleting from your phone does not delete from anywhere else
    HOWEVER deleting from your Photo stream does delete from the Photostream so anyone looking at the PS from any device will no longer see the photo
    But if your Mac iPhoto is set to automatically impor tphotos form PS or is you have manually imported photos from PS then onc ethey are imported they are on your Mac and change to PS will not affect them
    for more on PS see http://support.apple.com/kb/HT4486?viewlocale=en_US&locale=en_US
    LN

  • How do you spoof the ethernet MAC address?

    I cant seem to get this to work...
    sudo ifconfig en0 lladdr 11:11:11:11:11:11
    ...the mac address never changes
    Message was edited by: navilon

    Threads seem to say you cant do it because of the hardware, but when I boot into windows i can do it just fine.
    any thoughts?

Maybe you are looking for

  • What is the best way to verify default heap size in Java

    Hi All, What is the best way to verify default heap size in Java ? does it vary over JVM to JVM . I was reading this article http://javarevisited.blogspot.sg/2011/05/java-heap-space-memory-size-jvm.html , and it says default size is 128 MB but When I

  • How to change page order in a PDF file?

    Hi, how can I change the page order in my PDF file? I had read that it is possible but my editing options are showed gray and also my security settings cannot be edited. Do I need a special software? I have Acrobat Reader, and my document was exporte

  • Message "problem with photo with the filename '(null).

    I get the following message "There is a problem with the photo with the filename '(Null).'  The full resolution version of this photo either cannot be located or is corrupt.  Please replace the photo or delete it from your book."  This message appear

  • Assembly cost rollup wrong for averag cost org

    HI, For two of the assembly items , when we complete wip jobs cost is coming as very less. When i see the item cost for these 2 assembly items , it seems cost rollup is not correct. Cost elements unit cost and material are showing up same value :X$ R

  • Poor resolution in linux

    hi... i find that the resolution of movies played thru jmf is poor in linux as compared to that in windows. Anyone knows why? can anyone suggest how to improve it? Thanks and regards...