How do i fix a dead spot at the bottom of an ipod touch?
I have a dead spot at the bottom of my screen. I can swipe, put my password in, and slide through the home pages. However, I am unable to select either of the original four menu options (Messages, Safari, Settings, or Music). I dont know what to do, it was literally just working until i recorded a video and it gave me a hard time stopping the recording. Ever since then (about 30 minutes ago) The bottom of my screen has been disfunctional.
Please help.
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings (if you can)
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Similar Messages
-
There is a small white light in the retina display on my ipad 3. Is this a dead pixel/light leak and how do I fix it? (Located at the bottom left side between home button and left corner)
Maybe this will show up better in green.
-
How do I reinstall an older version of the software on my IPod touch? Installed the latest update and now it no longer works in my car.
I'm sorry, but Apple does not provide a downgrade path for iOS. Because downgrading is unsupported by Apple we cannot discuss it on these forums.
You may leave comments at Apple Feedback. -
TS4062 How do I fix a -50 system error trying to synch my Ipod touch to Itunes
How do I fix a -50 system error? I am trying to sysync my Ipod To Itunes.
Hi MizFrustrated,
Thanks for visiting Apple Support Communities.
You may find the steps in this article helpful with troubleshooting an "error -50" during sync, as seen in the post below:
Resolve iOS update and restore errors in iTunes
http://support.apple.com/kb/ts1275
My iPod won't sync, iTunes displays a message saying "an unknown error occurred (-50)."
https://discussions.apple.com/thread/3113764
If the error message persists, and you are syncing with USB, try these steps next:
iOS: Troubleshooting USB-related alerts when syncing
http://support.apple.com/kb/TS5254
Best Regards,
Jeremy -
Over the past couple of months, my iPhone 3GS has had dead spots on the left side of the screen, preventing me from using the r, d and x keys, the number 4 and the semi colon and comma keys. Does anybody have any ideas on why this has happened or any ideas that I'll be able to fix this problem?
Just a note; I can't put my phone to sleep or turn off as my lock button isn't working, so I'm using the AssistiveTouch settings.
Thanks.hannahhfoskett wrote:
I would gladly upgrade to the next model if my contract was due!
This has no impact on the ability to purchase a new iPhone... it simply means that the newer one will not be at a fully subsidized price.
You could always take it to Apple and do an Out of Warranty exchange (I'm assuming the device is out of warranty) for $149 US. -
I have a new computer. I have copied Itunes library from an external hard drive. Itunes now tells me I cannot sync with my Ipod as it thinks the 20gb on the computer are different to the 20gb on my Ipod touch! What have I done wrong? How can I fix it? Alan
See:
Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
Sync Your iOS Device with a New Computer Without Losing Data - How-To Geek -
How I can fix this error message in the Windows Server - kCGErrorFailure: No workspace dictionary?
How I can fix this error message in the Windows Server - "kCGErrorFailure: No workspace dictionary"? This occurs after every startup or restart.
You probably don't need the hard drive and optical drive specs, but here they are?
======================
Intel ICH10 AHCI:
Vendor: Intel
Product: ICH10 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 1.5 Gigabit
Description: AHCI Version 1.20 Supported
HL-DT-ST DVD-RW GH41N:
Model: HL-DT-ST DVD-RW GH41N
Revision: PQ06
Serial Number: K3D9BH92251
Native Command Queuing: No
Detachable Drive: No
Power Off: No
Async Notification: Yes
Bay Name: Upper
HL-DT-ST DVD-RW GH41N:
Model: HL-DT-ST DVD-RW GH41N
Revision: PQ06
Serial Number: K3D9BH92251
Native Command Queuing: No
Detachable Drive: No
Power Off: No
Async Notification: Yes
Bay Name: Upper
Intel ICH10 AHCI:
Vendor: Intel
Product: ICH10 AHCI
Link Speed: 3 Gigabit
Description: AHCI Version 1.20 Supported
Intel ICH10 AHCI:
Vendor: Intel
Product: ICH10 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 3 Gigabit
Description: AHCI Version 1.20 Supported
Hitachi HDP725050GLA360:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: Hitachi HDP725050GLA360
Revision: GM4OA5CA
Serial Number: GEA534RJ06E63A
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Rotational Rate: 7200
Medium Type: Rotational
Bay Name: Bay 1
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk1s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk1s1
Content: EFI
OSXLION:
Capacity: 499.25 GB (499,248,103,424 bytes)
Available: 192.76 GB (192,758,513,664 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s2
Mount Point: /
Content: Apple_HFS
Recovery HD:
Capacity: 650 MB (650,002,432 bytes)
BSD Name: disk1s3
Content: Apple_Boot
Hitachi HDP725050GLA360:
Capacity: 500.11 GB (500,107,862,016 bytes)
Model: Hitachi HDP725050GLA360
Revision: GM4OA5CA
Serial Number: GEA534RJ06E63A
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Rotational Rate: 7200
Medium Type: Rotational
Bay Name: Bay 1
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk1s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk1s1
Content: EFI
OSXLION:
Capacity: 499.25 GB (499,248,103,424 bytes)
Available: 192.76 GB (192,758,513,664 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s2
Mount Point: /
Content: Apple_HFS
Recovery HD:
Capacity: 650 MB (650,002,432 bytes)
BSD Name: disk1s3
Content: Apple_Boot
Intel ICH10 AHCI:
Vendor: Intel
Product: ICH10 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 3 Gigabit
Description: AHCI Version 1.20 Supported
WDC WD2002FYPS-02W3B0:
Capacity: 2 TB (2,000,398,934,016 bytes)
Model: WDC WD2002FYPS-02W3B0
Revision: 04.01G01
Serial Number: WD-WCAVY7048785
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk3
Rotational Rate: 5400
Medium Type: Rotational
Bay Name: Bay 2
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk3s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk3s1
Content: EFI
BU2TB-Time:
Capacity: 2 TB (2,000,054,960,128 bytes)
Available: 1.1 TB (1,096,926,654,464 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk3s2
Mount Point: /Volumes/BU2TB-Time
Content: Apple_HFS
WDC WD2002FYPS-02W3B0:
Capacity: 2 TB (2,000,398,934,016 bytes)
Model: WDC WD2002FYPS-02W3B0
Revision: 04.01G01
Serial Number: WD-WCAVY7048785
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk3
Rotational Rate: 5400
Medium Type: Rotational
Bay Name: Bay 2
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk3s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk3s1
Content: EFI
BU2TB-Time:
Capacity: 2 TB (2,000,054,960,128 bytes)
Available: 1.1 TB (1,096,926,654,464 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk3s2
Mount Point: /Volumes/BU2TB-Time
Content: Apple_HFS
Intel ICH10 AHCI:
Vendor: Intel
Product: ICH10 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 3 Gigabit
Description: AHCI Version 1.20 Supported
WDC WD10EAVS-00D7B1:
Capacity: 1 TB (1,000,204,886,016 bytes)
Model: WDC WD10EAVS-00D7B1
Revision: 01.01A01
Serial Number: WD-WCAU43604330
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Medium Type: Rotational
Bay Name: Bay 3
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk0s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk0s1
Content: EFI
Data:
Capacity: 999.86 GB (999,860,912,128 bytes)
Available: 715.55 GB (715,549,786,112 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /Volumes/Data
Content: Apple_HFS
WDC WD10EAVS-00D7B1:
Capacity: 1 TB (1,000,204,886,016 bytes)
Model: WDC WD10EAVS-00D7B1
Revision: 01.01A01
Serial Number: WD-WCAU43604330
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Medium Type: Rotational
Bay Name: Bay 3
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk0s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk0s1
Content: EFI
Data:
Capacity: 999.86 GB (999,860,912,128 bytes)
Available: 715.55 GB (715,549,786,112 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /Volumes/Data
Content: Apple_HFS
Intel ICH10 AHCI:
Vendor: Intel
Product: ICH10 AHCI
Link Speed: 3 Gigabit
Negotiated Link Speed: 3 Gigabit
Description: AHCI Version 1.20 Supported
WDC WD1003FBYX-01Y7B0:
Capacity: 1 TB (1,000,204,886,016 bytes)
Model: WDC WD1003FBYX-01Y7B0
Revision: 01.01V01
Serial Number: WD-WCAW31850957
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk2
Rotational Rate: 7200
Medium Type: Rotational
Bay Name: Bay 4
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk2s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk2s1
Content: EFI
BUOSXLION:
Capacity: 999.86 GB (999,860,912,128 bytes)
Available: 697.88 GB (697,881,690,112 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk2s2
Mount Point: /Volumes/BUOSXLION
Content: Apple_HFS
WDC WD1003FBYX-01Y7B0:
Capacity: 1 TB (1,000,204,886,016 bytes)
Model: WDC WD1003FBYX-01Y7B0
Revision: 01.01V01
Serial Number: WD-WCAW31850957
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk2
Rotational Rate: 7200
Medium Type: Rotational
Bay Name: Bay 4
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
disk2s1:
Capacity: 209.7 MB (209,715,200 bytes)
BSD Name: disk2s1
Content: EFI
BUOSXLION:
Capacity: 999.86 GB (999,860,912,128 bytes)
Available: 697.88 GB (697,881,690,112 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk2s2
Mount Point: /Volumes/BUOSXLION
Content: Apple_HFS -
How do i fix a small bend in the corner on my macbook pro?
How do i fix a small bend in the corner on my macbook pro?
It depends upon the bend and the exact location. In all likelihood replacement will be the most efficient method of repair or just ignoring it.
Ciao. -
What does this error message when I try to do updates mean? And how can I fix it? Thanks. (The operation couldn’t be completed. (NSURLErrorDomain error -1012.)
James
maverick 10.9.1Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test. -
I have a Dead Spot in the Tone Curve
I have noticed when using a tablet while working in LR5 I have a dead spot in the upper part of the curve near the highlights portion. I thought it was just a result of my tablet being old and a cheaper model. I tested it with a new Intuos 5 Touch and had the same problem. I go to drag down or up on the upper part of the curve and it doesn't move or hangs up. It happens in all RGB channels also. Has anyone else had this problem or know why this happens? Thanks!
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. -
The display on my ipod touch is permanently zoomed. what did I do and how to fix it?
the display on my ipod touch is permanently zoomed. what did I do and how to fix it?
See:
iPhone and iPod touch: Home screen icons are magnified or large -
Good morning friends, I have a problem with my iphone 4s since I get a screen that just light it says "Activation Required" restored it and not corrected, I bought my factory unlocked iphone, how I can fix this, I had installed the version 6.0 as developer to
If you have a beta copy of iOS6
1. You are a developer and will know how to transition from beta
to release version and to use the Develpoer forum
2. You have a pirate copy of the beta and no-one on this Apple hosted Forum can help you
try Google -
How come when I go check for my purchased apps on my iPod touch 4g ios 6.1 it loads long then it crashes. Can this be fixed ?
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.alredy suggested
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
How do i fix error code 6A00 on the LCD screen of my Canon PIXMA MP810
how do i fix error code 6A00 on the LCD screen of my Canon PIXMA MP810
Hello drews,
To try and resolve the 6A00 error, we will want to ensure that no paper jams or obstructions exist in the printer. To do this, please follow the steps below:
ASF / Paper Output Slot
Turn off the printer.
Remove paper from the ASF.
Gently pull the jammed paper out.
If paper is visible from the ASF, use both hands to pull the paper out slowly.
If paper is visible from the paper output slot, use both hands to pull the paper out slowly.
If the paper tears and a piece of that remains inside the printer, open the scanning unit (printer cover) and remove the paper from inside the printer.
Note : Be careful not to touch the components inside the printer.
Turn on the printer and confirm that the Alarm light is off.
(If the jammed paper remains in the printer, the paper may be automatically ejected.)
Load paper back into the ASF.
Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
Top
Paper jams inside the printer
Turn off the printer and disconnect the power cord and USB cable.
Remove the jammed paper slowly using the following procedure.
Open the rear cover to check if the paper is jammed.
Pull out the cassette and check if the paper is jammed inside the cassette area.
Stand the printer with the rear side down, holding the document cover.
Press the tabs together and pull the green cover toward you.
Check if the paper is jammed.
(If you were not doing Duplex printing, you do not have to follow this procedure.)
Close the green cover and place the printer back to a normal position.
Reconnect the power cord and power on the printer. Confirm the Alarm light is off.
Load paper back into the ASF or cassette.
Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
Top
Clearing credit card-sized paper jammed inside the printer
Credit card-sized and 4" x 6" sized paper must be loaded properly. If this media is not loaded properly, it will feed into the printer and will not exit. Credit card-sized paper should only be loaded in the ASF and in portrait orientation. 4" x 6" sized paper can be loaded in the ASF or cassette. But must be loaded portrait orientation.
If credit card-sized paper was loaded in landscape orientation in the ASF and did not eject (exit), please follow this procedure.
Turn off the printer.
Load the same paper type that is jammed inside the printer in portrait orientation.
Power on the printer.
The paper stock in the ASF will automatically feed the jammed paper from the printer.
To resume printing, load the paper in portrait orientation.
If 4" x 6" sized paper was loaded in landscape orientation in the cassette and did not eject (exit), please follow this procedure.
Turn off the printer.
Open the rear cover.
Fold in four a piece of letter-sized plain paper.
Push in the folded paper until it hits the jammed paper.
If the jammed paper is visible from inside the printer area, pull it out and proceed to step 7.
If the jammed paper cannot be pulled out, push in the folder paper from the rear so the jammed paper is in between the feed rollers.
Pull out the folded paper and close the rear cover.
Power on the printer and confirm that the Alarm light is off. The jammed paper should automatically eject.
To resume printing, load the paper in portrait orientation.
If you still experience the same error after performing the steps above, please turn off the printer, unplug the power cord from the back and leave it out for at least 10 minutes, then plug it back in and turn it back on. If the error persists, unfortunately, the printer will require servicing to resolve the issue. Please click on the Contact Us link below to obtain your servicing options.
This didn't answer your question or issue? Find more help at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well. -
I have an iPhone 4S I've been useing a sever for awhile now. Downloaded new iOS now I'm getting 403 forbidden when trying to look up anything from the server. Regular 3G works. How can I fix so I can use the server?
Update: An Apple rep called me today to update the status of my return. I was told that the replacements for the BLACK iPad 2's was still another 3 weeks out (at least) so they offered me a brand new WHITE 16GB iPad 2. I could have that or continue waiting. I opted to go ahead and accept the offer of a new white one. Worst case scenario if I don't like the white one I have buddy that just bought a 16GB black one that he would be willing to swap it.
Maybe you are looking for
-
Wacom Intuos Pro with Ai zooming/panning using the stylus not working
I'm having a problem with my Intuos Pro Medium tablet in Adobe Illustrator CC 17.1.0 (Mac OSX 10.9.2) while zooming/panning using the stylus. I've set my primary button on the pen on Pan/Scroll. When you hold alt/option+primary button on the stylus (
-
PDF document opens as blank on Gmail on IOS7.1.2
I have been sent an email with PDF attachment (tradesman's quote). If I open with Gmail on Ipad on IOS7.1.2, the PDF form is blank ie there is no data in the fields, but all the text of the form used for the PDF is there. If I open on Gmail on Windo
-
How to fax several files (jpg, pdf) as a single fax?
Hi I want to fax a few files together as one fax (2 x jpg, 1 x pdf). In Windows it used to be a fax with attachments but what is the way in Leopard? Many thanks
-
Scanning my Express Wireless Network
Hi there, I have a cable connection to the internet, connected to my Express to create a wireless network at home for my Powerbook. My question is, can I 'look' at the network to see if there are any other computers using it? Basically piggybacking o
-
Hi, I have made two presentations in Keynote and need to export to QT Full Quality, manual advance, to include on DVD's Both presentations are the same except for the language. The English version lets me export no problem. However the Korean version