How do i fix my canon printer pro 9000 error 9100

service error 9100

Hello,
Please try unplugging the printer for at least 10 minutes. If the issue persists at that point, the best thing to do would be to get in touch with our technical support team at http://bit.ly/Phone_Support for further assistance.
Thanks!
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Similar Messages

Printing Issuse From Lightroom 4 To Canon Pixma Pro 9000 MK II

I have been trying to print from Lightroom 4 to a Canon Pixma Pro 9000 MK II. Whenever I try to print via the front try (for canvas) I get an error message (code 1281) and I cannot print. I have tried a few different papers as well as canvas and all of them give the same error code.
I have also tried printing from Elements 9 with the same problem.
I can print via the front try using Canon's own software, Easy Print Pro, but I cannot soft proof the image first and I cannot the the correct size of image either.
Does anyone have any idea how I can get round this problem?
I have spoken to Canon and they have passed the buck saying that as I can print using thier software it is an Adobe issue.
Printer: Canon Pixma Pro 9000 MKII
Software: Adobe Lightroom 4
Operating System: Lion OSX

The final answer was as per Rikk Flohr's instructions,
Lightroom>Print Module
Print Settings button Bottom Left-hand Panel
Set the Center Pull-down to Quality and Media
Paper Source: Front Tray
I was having difficulty finding these previously, thanks Rikk.

How do I fix my mac book Pro from running slow?

How do I fix my mac book Pro from running slow?

Why is my computer slow?
Step by Step to fix your Mac

How can i fix my mac book pro i bought in mid 2010, it is slowing down. the pin wheel does spin a alot.

how can i fix my mac book pro i bought in mid 2010, it is slowing down. the pin wheel does spin a alot.

try this;
open disk utility - verify disk permissions - repair disk permissions if errors are found. might take an hour or less - depending on how much errors needs to be repaired.
restart your macbook and see if that sorts it out for you.
also check your hard drive space. if your hard drive is almost full, that will also contribute to your macbook getting slower....
good luck

I am trying to get my iPad to print from hp air printer and it only prints on photo paper. How do I fix it to print on paper. I already put setting to copy on printer but it prints blank.

I am trying to get my iPad to print from hp air printer and it only prints on photo paper. How do I fix it to print on paper. I already put setting to copy on printer but it prints blank.

Thank you everyone. I figured it out. I thought that you can use regular paper to print pictures from photos on Ipad. This is not possible. I was able to use regular print paper to print from my mail. My problem is solved!!

What does this mean and how do I fix it: "The following warnings and errors were found during the validation of the current project: - There appears to be a broken asset in your project. Correct this problem before burning this project."

What does this mean and how do I fix it: "The following warnings and errors were found during the validation of the current project: - There appears to be a broken asset in your project. Correct this problem before burning this project."

It means that iDVD has found a problem with one of the movies added to the project. Did you edit the movie after it had been added to the project.
Create a new project and add your assets, movies, slides, etc. again and follow this workflow to help ensure the best quality video DVD:
Once you have the project as you want it save it as a disk image via the File ➙ Save as Disk Image menu option. This will separate the encoding process from the burn process.
To check the encoding mount the disk image and launch DVD Player and play it. If it plays OK with DVD Player the encoding was good.
Then burn to disk with Disk Utility or Toast at the slowest speed available (2x-4x) to assure the best burn quality. Always use top quality media: Verbatim, Maxell or Taiyo Yuden DVD-R are the most recommended in these forums.
OT

Managing Color with LR and the Canon Pixma Pro 9000 10.1.2.0 printer driver

I would like help understanding how to manage color in LIghtroom with the Canon Pro 9000 10.1.2.0 printer driver. When I ask LR to manage color in the Printing Module Color Management Profile, it warns me to turn off the printer managing color. But I cannot find where to do this in the driver.
The Color Options menu in the driver gives an additional choice for "Color Mode", but there are no choices here except "Standard", "Linear" or "Tone". The only Canon documentation I can find shows a choice to turn off printer management here, but this driver doesn't give me that choice.
If I look in the driver's "Color Matching", I see only two choices: ColorSync or Vendor Matching. ColorSync brings up Canon profiles like "Pro9000 Fine Art Photo Rag", but selecting one of these gives a warning of unexpected results. This pushes me back to Vendor Matching. But is this turning off the printer driver and leaving it to Lightroom?
Right now, I am getting the best results from choosing "Managed by Printer" in LR's Color Management Profile, and setting "Color Matching" in the Canon driver to "Vendor Matching". If I instead choose one of the Canon profiles in LR's Color Management Profile (and it tells me to turn off the printer managing, which I cannot do), then my prints have a slightly bluer color cast.
Is there a way to turn off the printer managing color in this driver and turn this over to LR, or am I getting the best results possible with the printer managing color anyway?
I am using a 2.4 GHz Intel iMac with OS 10.5.4, 2 gigs SDRAM, standard ATI Radeon HD 2600 Pro video card. I downloaded the Canon printer driver from their website, so I assume this is the latest. there is another driver available at their website, but for a lower bit depth. Should I abandon the 10.1.2.0 for this other one? I work with Nikon D300 NEFs, and I assumed the higher bit depth printer driver will work better with these images.
Any help will be greatly appreciated!

Dear DYP: Unfortunately, those choices are not available in the 10.1.2.0 Canon Printer driver. There are only 2 radio buttons, ColorSync and Vendor Matching. ColorSync then provides a drop-down menu, with no choice for turning off the printer driver.
But I think I found the answer. I found a deeply buried FAQ on the Canon site (no direct URL; sorry!) Here it says:
"Issue: How do I disable the printer driver color correction when using the CUPS driver in Mac OS X 10.5.x?
Solution: Change color management options for printing (Mac OS X 10.5.x)
Change color management options for printing
Open the document you wish to print.
Click 'File' and then click 'Print.'
Note: If the Print window contains only two pop-up menus, click the triangle beside the Printer pop-up menu for expanded options.
Select 'Color Matching' from the Print Options pop-up menu.
Select 'ColorSync' if you want the application you are using, and not the printer driver, to control the color management of the printed output.
Note: If you are using Adobe Photoshop CS2 or CS3 and have selected 'Let Photoshop Determine Colors', the 'Color Matching' from the Print Options pop-up menu is automatically set to 'ColorSync.'
Select 'Vendor Matching' if you want the printer driver to control the color management of the printed output."
I tried it, and chose "Automatic" as a choice in ColorSync. The choices under "Color Options" are then greyed out, implying that the Canon driver is now turned off.
The prints came out great, with no color cast, and a little brighter than the printer managed prints.
So, Vendor Managed means printer manages, ColorSync means LR manages.
Thanks, everyone, for keeping me going on tracking this down!

How do i fix a black print screen after downloading adobe reader?

I downloaded acrobat and reader late last week on my mac. I've noticed when I go to print a pdf file, the preview screen is black and when i actually print, it's black. How do i fix this please?

Quit Safari
Go to Mac HD/Library/Internet Plugins
Look for "AdobePDFViewer.plugin" and "AdobePDFViewerNPAPI.plugin"
"Trash" them both. You may need to enter your admin password.
Empty the trash.
Relaunch Safari and open the PDF.
It should be OK.

How do I fix Creative Suite CS2 reinstall with error message "Missing or Invalid Personalization Inf

How do I fix Creative Suite CS2 reinstall on same Windows 7 Pro machine, with error message "Missing or Invalid Personalization Information / Missing Resources Library" when I attempt to reinstall from installation disk set? Was having trouble with Adobe Acrobat Pro 8; Uninstalled and am now stuck. You can email me if you like at [email protected] Thank you.

Hi Bill:
     I don't remember deactivating (after my XP PRO harddrive scattered)
when I did the first Windows 7 pro install of these programs and it went
fairly well except AA8 was a little problematic when converting from MS
Word.
     In my case the AA8 came with a Studio 8 suite of programs as follows:
     1) A Studio 8 installation disk
     2) A Creative Suite CS2 Premium set of installation disks.
     3) A Creative Suite 2.3 Premium upgrade disk with AA8
     I uninstalled AA8 and when I tried reinstallation the directions
said to do the Creative Suite CS2 Premium set of installation disks
first followed by the Creative Suite 2.3 Premium upgrade disk with AA8.
Now I'm stuck; What a mess.
     Thanks for trying to help.
     I will do as you suggest and go to
http://forums.adobe.com/community/creativesuites but FYI:
Bob Lane

How do I fix "kernel[0]: disk3s2: I/O error" message?

For the last couple of weeks, I have seen the spinning wheel show up on virtually any task I try to accomplished, especially when using Safari. At times the delay is just a few seconds and other times a delay for up to 20-30 seconds.
At first I thought it was Safari so I reinstalled the latest update. Went to Time Machine and brought back any programs that I had recently updated for downloaded and still no change.
I went to Activity Monitor and did not see anything unusual. then went to Console where I get the following error message on virtually any task I key in "kernel[0]: disk3s2: I/O error." i have Verified my drives and have repaired disk permissions. Still the problem persists.
What causes this error message and how do I fix the problem?

Any time you think it is safari, and that is one program where manually emptying the temp files and caches doesn't happen on its own automatically, you really need to do it yourself, or rely and hope on the "Reset" feature.
Anytime a program is updated, good idea to clean the temp caches anyway as they may cause trouble.
Check home library /Caches/MetaData and empty the contents, and the icon cache as well. When Safari launches, it copies the bookmarks into a cache folder as well so there are 100s or whatever files there.
Don't rely on Apple First Aid, and not with a maxed out system. Disk Warrior is reliable and finds more. Trouble is unlike TechTool Pro it is one at a time, and mostly one trick only, so it can be slow and can't do much to speed it up.
There are nice FAQs on preventing and troubleshooting kernel panics if you look and want to go that route.

HT4623 How do you fix it if it has a error 2001???

Ive tried restoring the device but everytime it gives me an error saying "error 2001". How do i fix this? i've tried different usb wires but nothings happened and the device has the latest software update. Please help

Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.

Spooler app problem wont print how do i fix? was printing fine now it won't

hello
i'm hoping someone can help me. my printer was working fine hp laserjet 1018, and now it wont print at all. i have uninstalled and reinstalled driver bust the prompt says spooler subsysytem app stopped working and was closed, the local print spooler service is not running. what do i do to fix this? please help.....
thank you!

I want to be able to help you but I will have to provide two documents because I do not know what kind of computer you are using. It seems that your Print Spooler is simply turned off and you need to get it running again. If you have an older computer, here is a document directly related to your printer:
--Spool32 Error Message--
I have a really good feeling you are using a Windows 7 operating system. This link is not a document but it has great instructions on "How To Restart Your Print Spooler Services."
I am happy to help and anxious to hear if this fixes the problem for you. If it does not, then what is the operating system of your computer (Windows XP Service Pack 2, Windows 7 32 bit, etc) and how is the printer connected to the computer (USB or on a network)?
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution!

HOW CAN I FIX MY CANON PIXMA 2120 WITH OUT THE CD

Solved!
Go to Solution.

Hi lisaberry,
If you are trying to reinstall the printer without the installation CD, you can download the drivers and software for the printer from the Canon USA website. So we can provide you with instruction applicable to your computer, please reply with what operating system is on your computer (version of Windows or Mac OS X).
If the printer is displaying an error, or if you are having another issue with the printer, please reply with a description of the error or issue and we will be happy to see how the issue can be resolved.
If this is a time-sensitive matter, additional support options are available at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

How do I fix Maverick Mail printing smaller font?

I just upgraded to a new MacBook Pro with Retina screen running Mavericks 10.9.1. Restored my stuff from Time Machine Backup of my old MacBook.
I discovered that Maverick Mail is printing all emails in smaller size than what they are written. 12 point Helvita looks like 8 point, or less, when printed from the Maverick Mail on a laser printer, also connected to my wife's iMac. Printing the same emails from the iMac, running Lion, prints in accurate 12 point size. I have printed other documents from my Mavericks MacBook, i.e. PDF's that I created on the old MacBook. Those documents print in original size. So, problem is with Maverick Mail.
For some reason, Mail is reducing the print size of the emails, no matter if the email is going to the printer or printed to a PDF file. The font size is reduced.
I have seen that others have had a similar problem with Maverick Mail.
Has anyone found a fix? Or do we have to wait for the Apple geniuses to get around to findiing their mistakes in Mail?

Keep the Powerbutton and the Homebutton pressed at the same time until you see the Apple logo on your screen.

How can i fix my Mac book pro sleep mode

Hi i am having troube with my mac book pro which i purchased in 2010. I am running Mac OS X 10.7.4, the time it took my computer to go sleep mode before was around 3 second and now it basically took 1 minute go on sleep mode. can anyone help me on this one?

try this;
open disk utility - verify disk permissions - repair disk permissions if errors are found. might take an hour or less - depending on how much errors needs to be repaired.
restart your macbook and see if that sorts it out for you.
also check your hard drive space. if your hard drive is almost full, that will also contribute to your macbook getting slower....
good luck

How do i fix my canon printer pro 9000 error 9100

Similar Messages

Maybe you are looking for