How do i get airport extreme to see 2 express devices after i told it to forget devices

when setting up express devices I indicated to forget devices and now need to set them up but airport utility nolonger sees them. how do i correct my mistake

To set up the AirPort Express......
With an AirPort Express powered on for a few minutes, hold in the reset button on the device for 10-12 seconds and release. Allow a full minute for the Express to restart to a slow, blinking amber light.
Open AirPort Utility
Click on Other WiFi Devices
Click on AirPort Express
The setup utility will open up and suggest a configuration for you. Follow the prompts.
If you are using an iPad or iPhone for the setup....
Tap on Setttings on the Home Screen
Tap on WiFi
Under the title of Setup a new AirPort Base Station....tap on AirPort Express
Set up other Express device(s) the same way.

Similar Messages

HOW do I get my Extreme base station and Express to join a Linksys network?

OK... so I have FINALLY enabled my SLINGBOX to view remotely by totally removing my Airport Extreme & Express from the network look. I was told they are both routers and I have to pick one. The Linksys network works fine for all networking purposes... what it WON'T DO is connect my USB printer or stream iTunes to remote speakers. NOW, I have been told by using the Extreme & Express in "client mode" I can do this.
Basically HOW do I get my Extreme base station and Express to join the exsiting Linksys network?

Sorry but the AirPort Extreme base station (AEBS) does NOT have a client mode.
The AirPort Express (AX) does have a client mode. The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.

How can I get iMovie 10 to see my iPhoto Library after I relocated it.

How can I get iMovie 10 to see my iPhoto Library after I relocated it. I moved my iPhoto Library to a secondary hard drive, because my main SSD wasn't large enough. I then upgraded to IMove 10.0.4 and also moved my iMovie Library to the secondary hard drive. When I highlight the iPhoto Library in iMovie there is nothing there. Any ideas on how to get iMove to find my relocated iPhoto Library?

I think I may have solved my own problem. I left cliked on the relocated iPhoto Library and went to "Open with >." I then went to "Other...." I then set the wind located in the bottom labled "Enable:" to "All Applications" and picked iMovie. It gave me a error, but the ultimate result was that iMove now was linked to my iPhoto Library.

How do I get AirPort Extreme to find Chromecast?

I just bought Chromecast for the bedroom and my AirPort Extreme can't find it. How can I get it to find my new Chromecast?

Ask Chromecast.
Barry

How do I get Time Machine to "see" my NAS device?

I recently set up a Drobo 5N for NAS. It works fine with my iMac. That is, Time Machine on the desktop immediately found the storage device and appears to be backing up to it. However, Time Machine on my Macbook Pros on my home network do not see the device at all. They do show the Airport Extreme (the Drobo is attached to Airport Extreme via Ethernet). The Firewall on the Macbook Pro has been turned off. All other networking functions seem to work fine. All the computers in question are running Mountain Lion. Anyone have any idea how to fix this? Thanks.

Backing up to a third-party NAS with Time Machine, if it works at all, is risky, and unacceptably risky if it's your only backup. This is an example of what can happen.
If you want network backup with Time Machine, use as the destination either an Apple Time Capsule or an external hard drive connected to another Mac or a mini-tower (802.11ac) AirPort base station. Only the 802.11ac base station supports Time Machine, not any previous model.

How can I get my iMac to see my bluetooth devices?

I have a couple bluetooth devices but my iMac does not see them on the list. I currently own a earbud set, jaybird bluebuds x. The Mac is seeing my bravia smart TV ..but not my iphone, or ipod..and not the earbuds. Any advice ?

I have a couple bluetooth devices but my iMac does not see them on the list. I currently own a earbud set, jaybird bluebuds x. The Mac is seeing my bravia smart TV ..but not my iphone, or ipod..and not the earbuds. Any advice ?

My airport extreme is flashing amber it says i need a ip address .... it was working just fine yesterday until i had to reboot cable modem how do i get my extreme to work again so i can have wireless

my airport extreme is flashing amber it says i need a ip address .... it was working just fine yesterday until i had to reboot cable modem how do i get my extreme to work again so i can have wireless..... please help!!!

Hi again Jen,
Most internet providers utilize "dhcp" -- you might want to check to see if your extreme is set to that function.
If you want to try, you need to go into airport utility and select MANUAL setup/ then click NETWORK button on top of the window. /select TCP/IP -- make sure that you see "Using DHCP" not MANUAL in the configuration window. If you do see using dhcp, click the renew dhcp lease button. Then you'd have to do the power down/up cycle again. If all this doesn't work, you can do a hard reset on your Extreme, which will bring it back to the way it came out of the box, then go through the same proccess that was used to set it up originally.

How do I configure my Airport Extreme to see the printer I have plugged into the USB port?

How do I configure my Airport Extreme to see the printer I have plugged into the USB port?

OK. The 6.0 version no longer has a printer configuration that I could find. You might try Printer Sharing in the Sharing preferences.
I would also check the printer's user manual for help with the setup, and that failing check the manufacturer's website and/or tech support.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How to set up airport extreme with TPG ADSL2 ?

How to set up airport extreme with TPG ADSL2 ?

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How do you use Airport extreme at hotels etc, when traveling? I can plug my computer into the Airport with my ethernet but how does Airport pickup signal?

How do you use Airport extreme at hotels etc, when traveling? I can plug my computer into the Airport with my ethernet but how does Airport pickup signal? What equipment & devices do I need to travel with to make this possible?

You may mean the AirPort Express.....not AirPort Extreme.....as the Express is a popular travel router.
The whole idea behind using this device is that the hotel must provide an Ethernet jack in the hotel room. Then you connect the AirPort Express to the Ethernet jack with an Ethernet cable and configure it to provide your own wireless network in the room. You still have to agree to terms, pay the fees, etc.
The problem with this approach is that it is getting very difficult to find hotels in North America that prrovide an Ethernet jack....most have moved to wireless networks and the others are not far behind.
So, if the hotel is already providing a wireless signal, the AirPort Express is of no use in that situation.
If you normally stay at the same hotels, and know that they provide Ethernet ports, an AirPort Express might make sense in terms of convenience.

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

How do I reset Airport Extreme Model A1034?

How do I reset Airport Extreme Model A1034?
I am using a MacBook Pro to set up the airport, but, I get this message:
"This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information."

You would download and install AirPort Utility on the PC.
For Windows 7 and above.....use AirPort Utility 5.6.1 for Windows - Support - Apple
For XP SP3 and Vista SP2......use AirPort Utility 5.5.3 for Windows - Support - Apple
For XP SP2 and Vista SP1......use AirPort Utility 5.4.2 for Windows - Support - Apple

How fast IS the AirPort Extreme?

I'm in need of a new router/modem to go along with my new ISP and new computer. (the computer is a windows) but i have 3 iMacs and 2 Windows.
I just have a couple of questions.
1. How fast Is the AirPort Extreme? Does it boost the speeds of the speeds you already get from the ISP?
2. Is it a router and modem all in one?
3. How compatible is it with windows? (can I set it up on a windows computer?)
4. Is it REALLY worth the cost?
5. What other router/modem combo can compare to it?

1. How fast Is the AirPort Extreme?
The Ethernet ports are 10/100 (100 Mbps max). The wireless interface is 802.11g (54 Mbps max).
Does it boost the speeds of the speeds you already get from the ISP?
No, the Internet access speed is limited by the connection speed to your ISP.
2. Is it a router and modem all in one?
It IS a router. It has a built-in 56k modem but it does not have a DSL or cable modem built-in.
3. How compatible is it with windows? (can I set it up on a windows computer?)
Ethernet and 802.11g are both standards. There is a Windows version of the AirPort Admin Utility which can be used from Windows to configure the AirPort Extreme base station (AEBS).
5. What other router/modem combo can compare to it?
Verify few other wireless routers have built-in USB printer support. Of those few devices even fewer are compatible with the Mac.

How to rollback the Airport Extreme to previous release?

Hello,
I need to know how to rollback the Airport Extreme to previous release.
I just updated my last generation Airport Extreme to the latest release because it was blinking orange the status light and it requested to be updated. Howver, doing so, it no longer recognize my AirPort Express nor my second Airport Extreme (2nd generation) that is bridged.
If anyone knows how to rollback the update I will appreciate it.
Thanks,
genbaez.

I just updated my last generation Airport Extreme to the latest release
We might be confused by last generation. does that mean Gen5??
If it is Gen5 you roll back by holding down the options key while selecting version.
All the previous versions applicable to your model should pop up.
Just select the one you want.. and it will proceed. You get no warning or other chance to stop it.. so choose well. 7.6.1 is IMHO the best when you are going to mix with older products.
I got about 10x link speed improvement doing extend wireless when I rolled back to 7.6.1 yesterday.
Also you should stop the airport utility annoying you.. turn off the firmware update reminders so they only happen once a week. Uncheck all of these. Ignore the update warning when it will inevitably happen.

How do i get airport extreme to see 2 express devices after i told it to forget devices

Similar Messages

Maybe you are looking for