How do I increase the field of view in Measurement and Automation Explorer (MAX) Version 3.1.1.3003
I am using Measurement and Automation Explorer Version 3.1.1.3003 to view pictures on a pc that are being sent from a video camera looking through a microscope. The image I see in the viewfinder of the microscope is MUCH smaller than the image that is displayed on the pc screen. Looking through the viewfinder of the microscope, I can see ~20 mm across the object, but the display from the camera in NI-MAX shows ~4.5 mm across the object. How can I change how much of an object is displayed on the screen in NI-MAX?
The camera is attached to the microscope with a camera adapter on the top of the microscope. The lenses the camera "looks" through and the lenses used when one looks through the viewfinder are the same, so theoretically, there should be no difference in what is displayed on the pc and what is seen through the viewfinder. We have ruled out the microscope and camera as the cause of the problem, which narrows it down to the NI-MAX software itself.
I saw in the forums that you can zoom out on an image; however, this does not change the distance across an image that is seen, just makes the picture of the same ~4.5 mm across the object smaller in size.
Any ideas or suggestions?
I have attached a picture of the object's image being displayed on the pc monitor. Where the field of view (FOV) in the microscope is almost 30 mm, the FOV displayed onscreen is about 7 mm. After contacting companies various times I discovered there was a reducing lens that goes in the C-mount adaptor, but it is over $300.
I thought maybe that the FOV could be changed in in NI Measurement and Automation Exploer (NI-MAX). Any ideas?
Attachments:
field of view.png 2437 KB
Similar Messages
-
I am running a set up which uses 2 identical USB Point Grey cameras of the same model (FL3-U3-13S2M-CS). Both USB cameras are plugged into the computer (blue USB cables).
When I open up Measurement and Automation Explorer and look under "NI-IMAQdx Devices" in the configuration tree, LavVIEW only recognizes one of the two USB cameras. Measurement and Automation Explorer only lists one camera, in which it recognizes it as "Point Grey Camera". Why this is occurring? How can I get LabVIEW to recognize two separate cameras of the same model?
Attachments:
PointGreyCamera.JPG 2847 KB
DualUSB.JPG 2932 KB
MeasurementAutomationExplorer.JPG 99 KBThat's about the old NI-IMAQ for USB cameras. IMAQdx has built in support for DirectShow connected cameras. IMAQdx should be able to use more than one DirectShow camera at the same time, but the Point Grey DirectShow driver may have some issues.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions -
Hi
I'm acquiring data on 8 analog input channels using a PCI-6052 E card. The data on channels 5 thru 8 is going to be between +1V and -1V. So for greater resolution I'm manually changing the range of these channels to +1V to -1V in the measurement and automation explorer. Is there a way by which I can make these changes directly using a VI ?
Thanks,
ShivHi
Yes you can, but only if you use the "AI Config" VI. AI config allows different gains for different channels. The "channels" and "input limits" inputs of the VI accepts arrays. The first element of the input limits array corresponds to the first element of the channel array. Check the "cont acq&chart (buffered).vi" in the LV examples. There you see what I mean!
Regards,
Luca -
How do I increase the font size in my email and maintain resolution.
Hi folks. Mr Newbie is seeking some help, I hope it is relatively straight forward, thanks
How do I increase the font size in my standard email and document views without losing resolution. Right now my font size in email, headers and text is less than that on my iPhone, it rather defeats the point of having a 27" screen if most of it is blank and I have to sit with my nose to the screen to read email. Thanks for your help, once you have stopped laughing. CTwo things you can do to easily aid with readability in Mail are as follows:
1) Increase the size of folders in the sidebar:
a) select "system preferences" from the Apple menu
b) select "general settings"
c) select small, medium or large under "sidebar icon size"
2) Increase the text in the main body of the email (both sent and received):
a) select "preferences" from the Mail menu
b) select "fonts and colors"
c) adjust font size for "message list font" and "message font". I have noticed this works properly while in classic mode, but in regular mode the message list font doesn't appear to change size.
Select classic mode by accessing Mail preferences and selecting the "viewing" tab.
Another shortcut is to right click on the toolbar, then select "customize toolbar", and then drag the "smaller / bigger" buttons onto the toolbar. Now you can decrease and increase font size as desired on the fly. -
I am having difficulties getting Labview to work with my NI card. I have a PCI_6225 card running on a Win 7 64-bit install. I had to download all of the drivers and installers from the NI site and during the Labview install, I recieve a prompt asking for my hardware drivers. Since I only have the compressed hardware installer, Labview doesn't like what it sees and continues the installation of LABVIEW. I then attempt to open an analog input channel through the Instrument I/O Assistant which displays the error seen in the image attached.
I know the hardware works because in the Measurement and Automation client, I am able to observe the analog input I hope to collect in LABVIEW.
Is there a fix to get LABVIEW working? I have tried multple installs of LABVIEW and am on a administered computer through my University's IT people. I have 'full admin' rights. Thanks.
Attachments:
error.jpg 254 KBHello jbaxter,
When you download the Drivers from NI's website, make sure you unzip them (extract them) to a folder on your computer before you install them. If you use the NI Downloader it should prompt you to unzip and run the files after the download is complete. You need to either repair, or reinstall DAQmx and NI VISA. Make sure you download the latest versions of these first:
http://search.ni.com/nisearch/app/main/p/bot/no/ap/global/lang/en/pg/1/sn/catnav:du,ssnav:sup/1//en/...
Then go to Control Panel»Programs and Features»National Instruments Software and click Uninstall/Change then go to DAQmx and NI-VISA and click Repair. You can then point to folder that you downloaded from NI's website (make sure this is not a zip folder, but the folder that has been extracted). Or you could choose Remove, and then reinstall them both again. Also if you are using GPIB, reinstall or repair the NI-488.2 driver.
Here are some relevant links:
http://digital.ni.com/public.nsf/allkb/DC808866AF7D5C0986256FCE006E9BAB
http://forums.ni.com/t5/LabVIEW/Again-I-O-Assistant-not-installed-correctly/td-p/1024807
http://forums.ni.com/t5/Instrument-Control-GPIB-Serial/quot-MAX-or-Instrument-I-O-Assistant-not-inst...
http://forums.ni.com/t5/LabVIEW/Install-Instrument-I-O-Assistant/td-p/1471516
Software Developer
National Instruments -
How do I increase the size of icons within Word and other apps on my MacBook Pro
Trouble reading icons on top of menu bars etc...ie Microsoft Word and even Apple software. How can I get the text larger over all on my 15" MacBook Pro?
?The icons in the menu bar and text can be increased by using a different display ratio. System Preferences>Displays. Try 1344x840 or 1280x800.
-
How do I get a copy of version 2.2 of Measurement and Automation Explorer?
I am also interested in what new features/changes were made in V2.2 relative to 2.1. I noticed 2.2 on some systems here at Intel but didn't see it on the I web site.
Updates to MAX are included with updates to your drivers or newer software (LabVIEW, CVI, etc.). Upgrade to the newest NIDAQ (6.9.2) or NI488 (2.0).
As far as differences, there were a coule of bug fixes (1 important had to do with SCXI-1520 configuration). Also, it supports the newest version of VI Logger. -
I am a student using LabVIEW and Compact Field Point to implement a
senior design project in Electrical and Computer Engineering. We
have LabVIEW 7.1 and a cFP-2020 and additional modules. We are
trying to use the CTR-500 module to output a pulse train to drive a
stepper motor. We have found instructions online of how to do
this, but they all use Field Point Explorer. The instructions
make use of options in Field Point Explorer that are not included in
Measurement and Automation Explorer (the software included with the
cFP).
I have downloaded Field Point Explorer 3.0.2 and followed the
directions. Now, in LabVIEW, when I using the newly created .iak
file, I get a dialogue asking to find the SubVI: 'FP Read (Float Array
-IO).vi'. Included with LabVIEW are subvis for FP Read, but not
with the float array part. So I figure I cannot use Field Point
Explorer created .iaks with LabVIEW 7.1. So how cannot I access
the same options in Measurement and Automation that I was able to find
in Field Point Explorer?
ThanksHi,
FieldPoint Explorer is no longer used to configure FieldPoint systems. However, I do not think that the configuring your system in FieldPoint Explorer is causing the error.
FieldPoint systems are now setup in Measurement and Automation Explorer (MAX). Information on setting up FieldPoint systems in MAX can be found in the MAX help under: Installed Products>> FieldPoint. Also, I recommend upgrading to the latest FieldPoint driver and version of MAX. The FieldPoint VI's will be slightly different when you upgrade, so there is a good chance that this will eliminate the error.
Regards,
Hal L. -
Increasing the Layout model view
very urgent
Hi everybody
How can I increase the layout model view, and from where in the property of the report I can increase it .
Please help in details .
Best regardsGo to the Layout Model and expand it. click the Main section and right click it. Choose the property pallete. There you can change the width and height of the report.
-
How do I increase the number of pages viewed in history?
how do i increase the number of websites in history?
What is the current value of the the read-only pref places.history.expiration.transient_max_pages on the about:config page?
*http://kb.mozillazine.org/about:config
See Marco Bonardo's blog:
* http://blog.bonardo.net/2010/01/20/places-got-async-expiration -
In Apple Mail, using Mavericks, how do you increase the size of the email message list that displays on the left side of the screen?
The font size is so small.
Thanks.Thank you for responding. After investigating and checking further, it was clear that only one of your suggestions changes the font size of the list of emails, also called the In-box. And that is the display resolution.
However, changing the display resolution affects the dots per inch of everything, everywhere and makes it larger.
Given the high end fee Apple charges for their products, and the generally well developed software they provide, it is hard to imagine they have not corrected this obvious slight of effort on the inbox text. At times Apple's "one-size-fits-all" and "it's our way or no way" mentality astounds me and makes me want to run back to Microsoft.
Evidently this is a well known mistake, which has yet to receive any attention.
Again, thank you for your effort and assistance on my behalf. -
Hi friends,
how can i increase the number of available segments from 30 to more in Personal Analysis Flexfield in HRMS. Because i have to add few more columns to existing key flexfield. but we have only 30 segments under each flex field.how can i achive this ?
Thanks in advance.Hi Avinash,
thanks for your reply.
As per ur suggestion i think i can achive my requirement.
but i have small requirement in addition to that.
when ever i open this special information, and if i click on this dff , it should disply the some value by calculating based on the data on special info form. can i achive this?
thanks in advance. -
How can I reset the DEFAULT zoom view in Firefox at 125%, like IE, so I don't have to reset it every time ?
I have seen this question asked previously and it seems there is no answer.
I know that one can change each individual web page (that reset defaults back to 100%) and, alternatively and apparently one can load an add-on to fix the default size at Full Zoom.
... But any hints on how to achieve a DEFAULT 125% zoom would be much appreciated.Press CTRL + 0
Have you tried Firefox's zoom feature? Font size and zoom - increase the size of web pages
You can "zoom" all sites using this add-on: [https://addons.mozilla.org/en-US/firefox/addon/2592/ NoSquint]. After setting your global zoom level, you can still fine-tune the zoom on individual sites.
After installing NoSquint, click the % on the Add-on Bar to call up site preferences, then click the Global Settings button, then the Zooming tab.
If you don't have the Add-on Bar displayed, you can right-click the new tab button ("+") or a blank area of the tab bar to the right of it and choose Add-on Bar from the shortcut menu.
You can experiment with sizes larger than 125%, but I wouldn't go much higher than 150% unless you have a large high-resolution monitor.
If there are particular sites that still present a problem, feel free to post their URLs.
You can find more information about the zoom features Firefox offers in these articles:
[[Text zoom]] - For zooming text only
[[Page zoom]] - For zooming the whole page (including images etc.) -
How does one increase the y-axis (amplitude) of the audio tracks?
How does one increase the y-axis (amplitude) of the audio tracks? My patient appears to have flatlined. I don't want to increase the gain, just the way the waveform looks on my monitor.
DrDtMM
The "Expert view" is a part of the new interface of Premiere Elements 11. In your version 10, you have the Timeline and the Sceneline view choices.
For now, I will assume that you are in the Timeline view where you utilize video and audio tracks and not a Filmstrip with scene slots.
I suspect that you may be after the following. Let us see.
To the right of where it shows the name "Audio 1" is a microphone icon. That represents the "Audio Display Style". There are two Audio Display Styles and you can select one or the other by toggling that microphone icon.
a. In one instance, you will see the wave form plus a horizontal orange line which is typically the Volume Rubberband for Volume adjust. This Display Style has a light green background.
and
b. In the other case, you will see a dark horizontal line, no wave form. That dark line is on a light green background.
I suspect you are at "b". Are you aware that "a" exists.
If you want a really blown up version of "a" to look at, you could separate the audio from the video, double click the audio to open the Preview Windows, and then scale up the Preview Window.
We will be watching for your follow up to see if we are getting in sync.
Thanks.
ATR -
How can I increase the font size in all my displays after it shrank after installing OS X Mavericks?
How can I increase the speed after installing OS X Mavericks? It is slower now.Reset the page zoom on pages that cause problems: <b>View > Zoom > Reset</b> (Ctrl+0 (zero); Cmd+0 on Mac)
See http://kb.mozillazine.org/Zoom_text_of_web_pages
Your plugins list shows outdated plugin(s) with known security and stability risks.
* Shockwave Flash 10.0 r45
* Next Generation Java Plug-in 1.6.0_17 for Mozilla browsers
Update the [[Java]] plugin to the latest version.
*http://java.sun.com/javase/downloads/index.jsp (Java Platform: Download JRE)
Update the [[Flash]] plugin to the latest version.
*http://www.adobe.com/software/flash/about/
Maybe you are looking for
-
I wasn't looking at what I was doing and I deleted an imessage conversation and I havent figured out how to get it back yet. I have my ipod backed up with itunes but not icloud. It is onlt that one conversation though and I really want to get it back
-
Hello All, I have generated a java proxy and trying to compile in Developer Studio. I am getting this error while doing so. I have all my jars in classpath. com.sap.aii.utilxi.misc.api.BaseException Below are the jars i have in my class path.. Anybos
-
Error Log when doing a Copy data from the Hyperion web Administration tool
Hello, I got an error message below when I was trying to use the copydata Administration tool in Hyperion Web. " MSG_COPY_DATA_OPTIONS_FAILED: An error occurred while running the specified calc script. Check the log for details." Could you please let
-
Firefox 6 crashes repeatedly on various sites without notice. I NEVER had this problem before. I reverted to the older Version 3. Multiple crash reports - can only fit two in the space below.
-
Seriously considering switching Entourage to Mail. Any switcher advice?
After 7 years of being a power Entourage user (it's the center of my business), I'm considering, for the first time, switching to the Mail/AddressBook/iCal combo. The main reason is the need to be accurately synced between all three of my Mac compute