How do i install sata hard drive?

ok, i am using right now my sony dvdrw on ide1 as master and ata hard drive on ide2 as master, booting to the hard drive. i am going to install an sata hard drive and use that as the boot drive, the normal ata as a storage drive only. how will i install the sata drive? do i install it to sata 1 and then durring the install of windows xp tell it to hit f6 for third party scsi drivers and then use the intel sata floppy driver disk that came with my board? it's the MSI-6728 board. or is there anything special i need to do in the bios or what?
oh yeah. what connection for power should i use? my powersupply has sata and normal, so should i use the sata power connector? and then what's this about legacy or something in the bios, or am i wrong?

Well first of all, you dont install the Intel S-ATA Driver Disc unless you are going to create a RAID Array....Go into the BIOS and on the "On-Chip IDE Configuration" Page Set the Options like this.........
On-Chip ATA Operate Mode : Legacy
ATA Configuration : P-ATA+S-ATA
Keep S-ATA Enabled : (Greyed Out Yes)
Keep P-ATA Enabled : (Greyed Out Yes)
P-ATA Channel Selection : Both
Combined Mode Operation (At first you have to set this to P-ATA Channel 1, then switch after you Move Windows to S-ATA)
Configure S-ATA As RAID : No
Then you are Going to have to Install the OS on The SATA and Just Move the Files that you want to save from the P-ATA HDD and then Remove the P-ATA Drive from the "Boot Device" List in the BIOS....
You really should List Your Full System Specs. When you POST...Create a "Signature" with your Forum User Control Panel...........Sean REILLY875

Similar Messages

How to properly install External Hard Drive

I'm trying to install my external eSATA hard drive on my 7216 HD DVR and it doesn't seem to be working. I get the notice to reboot the box and then I get the warning about it detecting the drive and that everything else on it will be deleted. I then click ok to accept and after that i get nothing. I then check my DVR recorded status and it looks like it only has the internal drive, percentage used is the same. How to i make sure the external is installed and what type of indication will i recieve? Does the DVR format the hard drive and if so does it let you know when it's completed?

I have the same issue. I think the drive needs to be formatted in a format compatible with the set-top box. I can't locate that ability in the menus for my Motorola box. Anyone know how to format using the box? Apparently reformatting via the computer is not acceptable???

How do you install new Hard Drive &

I just installed a new 30GB hard dri've on my Nomad Jukebox model DAP6G0.
When I power it up it say's, "critical error / can not load OS"
Where do I get the OS for the player and how do I load it to the player.
I'm using winXP
This is my 2nd post with no reply?
Can't anybody help me?

Duplicate post.
I replied to your earlier post.

Need help in installing a SATA hard drive with 865pe NEO2

Hello there
I need a help in installing a Sata hard drive ,it is WD 250 GB , my motherboard is 865PE Noe2 , the bios is the latest one
already I got another old hard drive ,not a Sata ,a regular IDE one installed as a master hard drive
I want to install the sata hd as a slave for the IDE hd for now to transfer the files and documents
I already physically installed the Sata hard drive yet the problem is that it was listed in the bios , I followed some of the steps here in the forum mentioned but all what I got is I found it listed as the fourth IDE master , not as the primary IDE slave
in Windows Xp Sp2 it is not listed of course in the windows explorer , but it is there in the device manager
look I am very confused and I tried most of the combinations in the ide configuration in BIOS
what should I do coz I am feeling so bad and stupid ,you can consider me a n00b in this hard drive thing

1st the sata drive cannot be listed as a slave drive to the ide master [key word=ide-can be configured as master OR slave, master IF only 1 hd, master and slave IF 2 hds], on the sata controler you can have master and slave, the ide cable has two connectors for the hds, sata has only 1 hd connector.
are you wanting to install the sata as primary master and move the operating sys to that drive, if so you will need an IMAGING software to move an operating system OR you could do a fresh operating system install to the sata drive then install your programs.

HT5634 How to put windows 8 on MacBook Pro via sata hard drive USB off of other computer

Hi I have recently purchased a MacBook Pro 15 retina. My old laptop was windows 8 but the motherboard crashed and I have the sata hard drive that has all of my data info including OS would I be able to use the OS on Boot camp without purchasing a new license? Also how would I do that? I have put the hard drive into a portable USB device so I can access it via USB 3.0.

Others will give a better answer, but I suspect that Windows validation will consider this a "significant hardware change", meaning that it will stop working and/or you won't be able to update. Even so, it costs nothing to give it a try and see what happens.

I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3??

I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3?? That seems to be just about all I can find out there, so far. Are those drives compatable with this macine? thx

SATA II

How do i wipe my hard drive and install Mountain lion

OK i wanted to install mavrick but i got my macbook pro in june of 2007 so it's to old. The command R does nothing when i reboot, and everything i find online about clearing my hard drive and getting ready to install mountain lion has that step in it. So how do i clear my hard drive so my computer is brand new like the day i bought it and also update my OS from snow leapard. Do i need to buy the disk for mountain lion or can i just download it? if someone has a link to something helpful i would love to have it.. Thanks

If you can't run Mavericks, you can't run Mountain Lion because they have the same hardware requirements.
Check that your computer is compatible with Mountain Lion/Mavericks.
To check the model number hold down the option/alt key, go to the Apple menu and select System Information.
MacBook Pro (Mid/Late 2007 or newer) model number 3,1 or higher
Your Mac needs:
OS X v10.6.8 or OS X Lion already installed
2 GB or more of memory (More is better - 4 GB minimum seems to be the consensus)
8 GB or more of available space
If your computer isn’t compatible, you might be able to upgrade to Lion.
Computer Compatibility - Lion                       Lion
Check to make sure your applications are compatible. PowerPC applications are no longer supported after 10.6.
Application Compatibility
Applications Compatibility (2)

How do I erase my hard drive? My initial operating system was Snow Leopard but I have upgraded to Mavericks OS. My Snow Leopard install disk ejects when I try and use it.

How do I erase my hard drive? My initial operating system was Snow Leopard but I have upgraded to Mavericks OS. My Snow Leopard install disk ejects when I try and use it.

Do a backup, preferable 2 separate ones on 2 drives. Boot to the Recovery Volume (command - R on a restart or hold down the option/alt key during a restart and select Recovery Volume). Run Disk Utility Verify/Repair and Repair Permissions until you get no errors. Reformat the drive using Disk Utility/Erase Mac OS Extended (Journaled), then click the Option button and select GUID. Then re-install the OS.
OS X Recovery
OS X Recovery (2)
When you reboot, use Setup Assistant to restore your data.

I recently brought a HD PVR, i put in the disk to install the hard drive and it said " This program doesn't support DOS Mode! how do i get out of DOS Mode?? Please Help

I recently brought a HD PVR, i put in the disk to install the hard drive and it said " This program doesn't support DOS Mode! how do i get out of DOS Mode?? Please Help

What exactly are you trying to do? PVRs are for recording from TV not computers.
Either way, if it's complaining about DOS mode, it's Windows oriented software and not Mac compatible.

Installing Windows XP on SATA Hard Drive

Hey. I have a maxtor 80gb SATA hard drive that I put in my new computer, and I want to install Windows XP on it. I see that the computer recognizes that it's there, but when I do the F6 process to get the drivers for Windows I cannot get anything for some reason. I hit F6, and it gets to the point where it asks me to install a disk with drivers, and I put the floppy for the VIA drivers in the drive (I'm using VIA after all I've read), and nothing happens. I don't even hear the floppy doing anything. after a few seconds of "please wait" the same screen comes up telling me to put the floppy containing the drivers in. Does anyone know what the problem could be? Also, in bios, it seems to recognize my floppy drive, since it lists it, and I can use it as a boot drive. If someone could help me out, I'd appreciate it. Thanks.

Hi
What is meant is the floppy is controlled from 2 parts of bios.
1. go to advanced bios features, set floppy seek to enable, set boot sequence to floppy, CD, HDD(BB1 = SATA), enable other devices. Then go to integrated peripherals, make sure PATA IDE and SATA IDE are enabled, just below is floppy controller, enable that, then SAVE and exit,
If the floppy cable was inverted, the drive light would be on all the time, if it flickers oon and off, it is OK.
Now try the F6 routine, if it still does not work then a new copy of floppy may be needed.
Cheers
jocko

Installing a second SATA hard drive - Problems booting

Hi,
I currently have one Maxtor 160GB SATA hard drive in my system with my operating system installed. I have another identical hard drive that I'm attempting to install now, into the second of five available SATA ports on my MSI P965 Neo motherboard.
When I plug in the second hard drive, though, Windows will not boot. It gets to the Windows logo screen with the progress animation, but before even the animation can begin, it stops and the screen freezes. This does not fix itself with waiting.
My boot priorities are set to: DVD-ROM, CD-RW, hard risk. The hard disk priorities are also as they should be to my knowledge - although it can be tricky because when ordering, both disks have the same name. I have tried with either one on top of the list, and you cannot remove a drive from the list alltogether.
The SATA cable is in perfect condition. My BIOS is up-to-date.
When I plug the hard drive in when the system is already running, Windows will detect it and files can be written/read flawlessly. As soon as I restart, however, I run into the same issue.
The first HDD, with the OS on it, is in SATA 1, the second HDD is in SATA 4. Ports 3, 6, and 7 are unused.
I'm out of ideas at this point, I don't see any other options that need to be changed.
I'd appreciate any input you can offer - thanks in advance!

I would debug this drive you are talking about which clears off all data and partitions information. Take out the good drive and leave in the dodgy one. Boot to a floppy with this dell win95 boot disc.
http://support.dell.com/support/downloads/download.aspx?c=us&l=en&s=gen&releaseid=R19775&formatcnt=1&libid=0&fileid=19601
When at the A: prompt: type debug and enter, you get a (-) prompt and then enter the following script exactly:
F 200 L1000 0 (enter)
A CS:100 (enter)
xxxx:0100 MOV AX,301 (enter)
xxxx:0103 MOV BX,200 (enter)
xxxx:0106 MOV CX,1 (enter)
xxxx:0109 MOV DX,80 (enter)
xxx:010C INT 13 (enter)
xxxx:010E INT 20 (enter)
xxxx:0110 (enter)
g (enter)
q (enter)
restart your system.
Now you can put back in your first drive as well, boot up into windows and use the disc manager to repartition and format.
Old school! If you are still having problems I would replace the drive.

Just installed new hard drive in mac book pro 15", when trying to boot OSX from original disk I still get a folder with a question mark in it. How can I reinstall the OS?

Can't seem to get my mac book to boot from the CD after installing new hard drive.
I keep holding down "c" while restarting the machine with the disk in but it just keeps ejecting the disk and giving me a folder with a question mark.

If your on 10.5 with a Intel Mac, I think Apple has jinxed the firmware so you can't boot from the 10.5 disk anymore.
So far several people, myself included, can't boot from a 10.5 OS X disk on a Intel Mac.
Your going to have to buy a 10.6.3 Snow Leopard retail disk, it's wayyy better than 10.5 anyway, faster and most stable even better than Lion. Have to buy iLife though as it doesn't come on the 10.6.3 retail disks, only free with grey disks.
http://store.apple.com/us/product/MC573Z/A
https://discussions.apple.com/message/16276201#16276201

How can i partition my hard drive with lion on it and install snow leopard from time machine

How do I partition my hard drive which has lion on it and reinstall os6 from my time machine?

You going to need a second harddrive. It is riskie to resize your haddrive with live data on it. You need a backup of the data. That said, you might as well copy your data to the second harddrive. Repartition. Then copy the data back. I bought a 128gig flash drive from walmart for $32.
There were repartition commands introduced in 10.4.6 to repartition the harddrive.
For what it is worth, you can non-destructively partition a harddrive from single user mode in 10.4.6 or greater. Of course, you should have a backup of the harddrive.
http://www.ffnn.nl/pages/articles/apple-mac-os-x/nondestructive-partitioning.php

Seagate 300gig sata hard drive not recognized

I'm trying to install a seagate 300gb sata hard drive in my dual 2.0 g5.
I can plug in the two cables and the drive fits in fine, it even spins, however the computer does not recognize that the drive is there.
I've checked the sata in the system profile and tried disk utility but it is simply not there. Could this be a wiring problem or a bad drive? How do I check this?

My guess is that it is a Seagate 7200.9 with SSC on. If that is the case you will need a PC and this tool:
http://www.seagate.com/support/kb/disc/faq/ssc.html

How to add a 2nd hard drive to HP Pavilion DV7!

How to add a 2nd hard drive to HP Pavilion DV7-3165DX, product # WA794UA or WA794UAR.
(1) Order HDD, hard drive, hardware kit. HDD hardware kit includes mounting rails, static shield, screws, rubber isolators, and SATA to motherboard cable. Check your model & Product # for compatibility.
HP Parts HDD hardware kit 517639-001 for DV7-3165DX product# WA794UA and WA794UAR.
(2) Consult Drives - Windows 7 PDF, table of contents, 7 Replacing a drive in the secondary hard drive bay. This will show you how to install a 2nd HDD in a HP DV7.
Drives - Windows 7 PDF
(3) In Windows 7 select Computer, Select the HDD installed, Format (if not already formatted).
(4) If HDD does not show up in Windows 7 under Computer, go to Start (Menu), Search Programs and Files, enter "Computer Management", select Storage, Disk Management (Local), look for the Bay 2 HDD (should show up as Disc 1, Bay 1 HDD should show as Disc 0), Format the 2nd HDD (The one you just installed).
Update: I have the 2nd HDD (WD 1TB) installed, Windows now recognises it after completing the steps I mentioned in step 4, Format with default allocation NTFS 931.51GB free, 118MB used for formatting. Format with default allocation exFAT 931.51GB free, 1MB used for formatting. I selected NTFS format to reduce file fragmenting.
This question was solved.
View Solution.

When i added my 2nd HDD I was ready to get it ordered and shipped, so it would arrive before I arrived home. I also was not sure if it would be offered anywhere else and be 100% compatible. The quality of the factory HP part is good. Since then I found a cheeper source. Newmodeus DV7-3xxx Hard Drive Caddy $27.95 +tax +shipping. Not sure if the quality is the same. If this helps you, post your results and kudos.

How do i install sata hard drive?

Similar Messages

Maybe you are looking for