How do I know if my Airport Extreme Card is going bad?

I have 3 computers on a home network. I have the router (Airport Extreme) in my guest house and it is working properly. The tenant is able to get her email and browse just fine. I also have a Airport Express in the front house that extends the signal via WDS. I have a 24 inch Intel iMac 2.4 that is connected to the network and runs fine. When I check in the Airport utility the iMac can see both routers. I have a Power Mac G5 2.0 that has a Airport Extreme card in my studio which is behind my garage. It shows that it is connected to the network and at full strength but I cannot browse or get mail. I tried to run diagnostics but when I do it does not find my network. I also cannot find either one of the routers from the Airport Utility even though the Mac is about one room away from the main router. I tried renewing the DHCP. I also even uninstalled and reinstalled the Airport Extreme Card with no luck. I can see my network from the Status Bar where the Airport Signal Strength is but again...cannot find the routers in Airport Utility nor find the network within the Networking Diagnostics.
Any advise?

Little antenna is still intact. Everything looks good on that part. If I take it out the bars go grey. Yes this system was working fine with very good download speeds up to 1mb/sec (usually 400 to 700 kbps) up until a few days ago.

Similar Messages

How do I know if my Airport Extreme can do WDS?

Hi,
I have a 4th generation Airport Extreme and an Airport Express (don't know the generation). My plan is to create an extended wireless network based on WDS.
On my Airport Express I can select 'participate in a WDS network' in 'Wireless Mode', but I'm not able to select it on the Extreme. Both are running 7.5.2.
Does the 4th generation, in fact, do WDS or not? If so, how?
..Jacob

One thing I'm abit confused about is, that both my APs are connected with ethernet to my network, and I would like all communication between the APs about 'extending the network' to be inside ethernet, since they can't hardly see each other and with this I get really poor performance. Is this possible in anyway?
My solution now is I have created my wireless network on both APs, and allow them to be extended. Is this the best way to get the best performance in my situation?
You have what is called a "roaming" network if you have both wireless access points configured to "create a wireless network" using the same wireless network name, security and password. This type of setup allows maximum bandwidth on the network.
So, you would not use either WDS or the "extend a wireless network " setting with the "roaming" setup.

How do I know if my airport Extreme 802.11n needs updated firmware based on heart bleed issue using Mavericks?

I have Mavericks on oour laptops. I have an Airport Extreme 802.11n WI-FI not sure when I bought it. THe article by Tim Cook and Heartbleed issue is very technical and only mentions Leopard operating system. So do not know if I need to upgrade firmware or not. Not sure I undertand "Back to my Mac" or what to do? Also have an airport express.

it doesn't
only the newer AC/tower designed models required the updated firmware

How do i know if my airport extreme is working

my airport extreme is blinking orange, however my computer says it's connected?

This is usually an indication that the AirPort Extreme has a message for you that a setting may need to be adjusted, or that a firmware update is available for the AirPort Extreme.
Use AirPort Utility to find out why the amber light is blinking.
If you have a Mac, click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X Version number that you see there....and we can give you the steps to run the check using AirPort Utility.

IMac won't detect airport extreme card

i just bought an airport extreme card for my 1.25 GHz G4 iMac. i have installed the card in my computer, but for some reason my computer hasn't detected the card.
i read some suggestions in other discussions, and have tried almost everything. i have reset my PRAM and run the apple hardware test. the card still has not been detected. i have also installed the latest software update for airport. still nothing. someone also suggested resetting the PMU, but i read up on that and don't see how that would help with an airport extreme card.
i'm wondering if maybe i didn't do a good job of installing the card. it seems easy enough, but after i inserted the card and attached the antennae, the card felt sort of loose in the slot. i don't know if it's supposed to be a tight fit or not. i pushed the card in until it go any father, but i didn't want to push it too hard for fear of breaking something.
any suggestions?
thanks.
iMac G4 1.25 GHz Mac OS X (10.4.6)
iMac G4 Mac OS X (10.4.6)

i figured it out. my card wasn't pushed in all the way. DOH!

How to set up 6th Generation AirPort Extreme to cable modem as a wireless router and then connect my 3rd Generation Time Capsule to AirPort Extreme as a wireless extender?

What is the best way to set up my 6th Generation AirPort Extreme (A1521) to my cable modem as a wireless router and then connect my 3rd Generation Time Capsule (A1355) to my AirPort Extreme as a wireless extender? I live in a small 1 story house and I currently have the Airport Extreme connected to my cable modem in the living room and the Time Capsule plugged into the wall in my bedroom. I am able to wirelessly connect to the internet using the AirPort Extreme as my router and I can also do wireless back ups to my Time Capsule. My problem is that my connection seems to be really slow! My 1TB Time Capsule back up is only half way complete and it has been 3 days! My computer has been backing up all day and night for almost 72 hours and its still not even 75% complete. I have backed up to this Time Capsule in the past and it never took this long. I am thinking that when I set up my AirPort Extreme and Time Capsule using AirPort Utility I must have set it up incorrectly or something.
How do I set up my Airport Extreme and Time Capsule for the fastest possible internet speed and back up speed?
Thank you,

AirPort Utility 5.6 works with AirPort Extreme 802.11g base stations.
It works with N version airports.
It will also show details of the AC model but cannot be used for the setup.. mostly.
I purposely got the new 6th Gen Airport Extreme so my internet connection would be a lot faster!
Your network will be much faster when you have AC client directly connected to the AE. Older client will go no faster.. but what is worse.. extend wireless is mixing new and old wireless standards.. guess what one wins.. OLD.. So when you extend wireless.. you have no improvement whatsoever. This whole post is about extending wireless.. so you cannot extend to older equipment and do any better.. maybe slightly better signal although from your comments that isn't happening either.
I would rather not have to use an ethernet at all with the TC and I don't know EOP adapters are!
If you do not use ethernet then you are going to be forced to accept slow speed.
EOP (ethernet over power). Also called homeplug in the US.
http://en.wikipedia.org/wiki/HomePlug
Provides a method of networking over power cabling that already exists in your house.
So what your saying is for the fastest internet speed and back up speed possible I should keep my Airport Extreme plugged into my Modem and keep my TC set up as a wireless extender? Then when I want to do back ups I should plug an ethernet cable from my TC to my MacBook Pro?
To spell this out.
A wireless link to an extended device will go very slowly.. if it is not direct.
So lets say you have a laptop sitting in the lounge.. Your connection goes.. Laptop- - - - - AE- - - - -TC.
That means two wireless links.. wireless has this nasty half duplex and single channel nature.. it can send or receive (Tx or Rx) but not at the same time.
Ethernet by contrast does both at once. It is full duplex.
Wireless can talk to one client at a time.. so if there are multiple items using wireless lets say 4 devices.. then your computer gets a 25% time slice. Since wireless cannot handle multiple simultaneous connections.
Ethernet by contrast can connect multiple computers to multiple destinations at the same time.. all transmitting and receiving at full speed.
When you put all this together.. there are a couple of rules for fast connection.
1. Use ethernet at all times. Where you cannot use ethernet use anything but wireless.. eg EOP (homeplug) at least to try and get rid of wireless.
2. Where you must use wireless use it sparingly and make sure it is never more than one hop.. ie never have an extend wireless (repeater is more usual term). Repeater will cause instant slowdown of 50% and maybe up to 75% just because it is so inefficient.
3. Fastest wireless is 5ghz but it has very short range.. you need to be up close and personal to get it working.
Apple routers however unless you do manual setup I suggest are set to connect to best signal strength not best speed. It will therefore use 2.4ghz at 25% less speed than 5ghz because it is 1db better signal.. this madness means you need to setup manually for the best setup.

How do I remove the orange ribbon connector from the airport extreme card.

It's the last thing keeping me from intalling the new card. Does anyone know how to remove it. And why does the new one have a plastic tab sticking out next to the antenna port?

the card inside PB G4 17" is physically different card than the retail card.
retail card has plastic tab to pull it out of the slot of compatible models:
http://docs.info.apple.com/article.html?artnum=107440
card for 17" has a cable built in:
http://www.powerbooktech.com/part,name-Airport-Extreme-Card-for-PowerBook-G4-17, powerbook-aluminum-17.htm

How do i set up my airport extreme to access from my work windows based PC

How do I set up my airport extreme to access from my work windows based pc?

To mount the AirPort Disk in Windows 7 or Vista:
Open the Network browser by double-clicking Network on the Windows Desktop.
The AirPort Extreme base station name should appear in the browswer.
Double-click the name and you should get a login prompt.
Now depending on how you set up disk access:
In the Name field, either enter the user account name or for base station/disk access, leave this field blank.
In the Password field, enter the base station, disk, or user account password.
Select the volume(s) you want to mount, and then, click OK.

How do I set up my Airport Extreme to best use multiplayer games locally

How do I set up my Airport Extreme to best use multiplayer games with my family. Everyone is located in the same house and uses the same router.
I have tried a few games but have not successfully connected 2 players

That is a weird question, as your GAMES could be interpreted a hundred different ways. Are we talking about third party devices here or what?

How to setup a network setup with an airport extreme card in a mac pro

I have installled an airport extreme card in my mac pro. Restarted the mac. The AP black triangle appears on right top of the screen. If I activate the AP than the a light grey triangle appears, with grey bars. I can create a network, than the triangle becomes dark grey with an kind of black computer icon in the grey area. The signal strength shows all blue bars.
I have two other wireless networks (linksys and another for streaming music) both are working and detected by my imac. But the mac pro does not detect these networks.
I would have thought that the two networks would be detected automatically.
Please some advice to solve this problem
Imac G5; Mac pro Mac OS X (10.4.4)

You won't believe this, but the card is a crock. Mine was installed by an Apple tech at an Apple store. He obviously did not check out reception.
At home, I tried setting this up right next to a Netgear wireless router (2 feet away!), and got no signal bars. Yet I pull the cover off the machine and I get 4 bars and can connect to an 802.11g network. This stinks. What idiot at Apple designed a card where the antenna is a 1" square piece of metal? Could this be an emi cage? Where did they hide the so-called "built-in" antenna. Who knows?
See if you can aim the back of the machine toward the wireless router. There is a back door into this mother, through the fan(ny) opening.

How do I make my new Airport Extreme a base station?

I have been using an Airport Extreme (5th generation) as my base station router for a few years. I set the main network for my and my wife's use and created a guest network for when my sons visited and needed to use the wi-fi connection. I used passwords for both networks. Today I purchased a new 802.11 ac Airport Extreme. I unplugged the 5h gen. Extreme and plugged in the new Extreme. After a short hunt, my new 27" (late 2013) iMac found the new Extreme and had me set up a name and a password for it using Airport Utility. I was expecting it to ask if I wanted to set up a guest network, but it did not. I was expecting it to ask since I believe that is what happened when I installed my 5th gen Extreme a few years ago. For the 5th gen Extreme, I had to enter a password to protect settings on the Extreme, a WPA2 password for my main network and another password for my guest network. It took about 10 minutes to set up. For this new Airport Extreme I entered just one password. It took about 2 to 3 minutes for the entire setup. When I checked the menu in the Airport Utility under "Base Station", all lines are grayed out. Under the File Menu in Airport Utility, "Configure Other" is available, but "Import Configuration file" and "Export Configuration file" are also grayed out. I checked Network Settings in System Preferences and I see my new network name in the Wi-Fi menu and under the "Advanced..." button, I see the old and new Networks listed in the "Preferred networks" box.
So, how do I get the new Airport Extreme to act as the Base station and be able to enter a guest network? Does it require me to delete the old Network name from the Advanced... button page in System Preferences > Network Settings? Will I just have to start all over with the new Extreme to make it a base station?

Hello Leo,
I'm not at home so can't confirm but I can only assume that maybe some of the "old" settings in airport utility have changed, and simplified. Hence why you probably only need one password.
When I bought the new "tower" like AirPort Extreme, I just plugged it into the Ethernet, powered it on with the previous generation Extreme in place and in Airport Utility it just asked me if I wanted to copy the settings to the newer device, which included a few "port forwarding" settings. All done in this sequence. I didn't have guest network set up but you can still set up guest network under wireless in Airport Utility, hope this helps!

How do i use a 2nd airport extreme both are newer models

how do i use a 2nd airport extreme both are newer models

I assume that you mean that you want to extend the range using wireless only.
This Apple Support Document will tell you exactly how to do that:
http://support.apple.com/kb/HT4259
The instructions assume that you have AirPort Utility 5.6 for Mac OS X Lion , so if you have not already done so, you will need to download and install this application to track the instructions in the support document.

How do I extend my existent airport extreme network by addition of a 2nd airport extreme?

How do I extend my existent Airport Extreme network by addition of a 2nd Airport Extreme?

Can you clarify which version of the AirPort Extreme that you have now along with the model that you plan to use as the second device?
The older "round" AirPort Exteme or the newer "square" version with rounded corners?
Are you planning to extend using wireless only.....or by connecting the AirPort Extremes using a wired Ethernet connection?

How can I access HDD on Airport Extreme with iPad

How can I access HDD on Airport Extreme with iPad

Without third-party software I don't think you can. An iPad has no user-accessible interface to a file system. Just what is it you're trying to do?

How do I install a airport extreme card in a mac pro (Intel 2008)

How do I install a airport extreme card in my mac pro (intel) 2008 computer

What Wifi Cards Do Mac Pro 2008 model use???
http://meanderingpassage.com/2007/07/18/how-to-installing-an-airport-extreme-car d-in-an-intel-mac-pro/

How do I know if my Airport Extreme Card is going bad?

Similar Messages

Maybe you are looking for