How do I make my HP Deskjet 6980 printer Web Enabled?

I cannot figure out how to make my printer web enabled so that I can use ePrint.

According to this, it can.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01619067&lc=en&dlc=en&cc=us&product=3857218#N29...
It's no big deal really. Just trying to figure out the email so I can print from my phone when I'm not at home.

Similar Messages

How can i make a email for my printer

how can i make a email for my printer to send the things to the email and get it printed if i was out of the house my printer model is 3525

Hi alhashmi_sy,
Welcome to the HP Support Forums. I see that you would like to learn how to setup the ePrint feature of your Deskjet Ink Advantage 3525 printer.
The first step is to connect your printer to your wireless network. Please follow the steps in the Installing the Printer Software for a Wireless Network Connection document for your operating system. If you have already setup your printer with a USB cable, each operating system section has the steps to switch from the USB connection to a wireless connection.
After connecting the printer to your wireless network please follow the steps for Getting the Printer Claim Code. Once you have the web services information sheet with your claim code please Set Up a Custom Email Address for ePrint.
You should now have a customized ePrint email address for your printer. If you run into any issues please let me know at what step things went awry and the contents of any error messages. Please also let me know what operating system you are using on your computer (whatsmyos.com). Thank you.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

How can I make signature darker when I print the report?

I need to put my manager's signature on the report. The signature is too light, How can I make it darker when I print the report?
I used file link and OLE, both did't make it.
Thanks.

No way to do it directly in the report. You need to work with signature image file using any graphic software to increase its contrast. The easiest probably would be to use Paintbrush and change the image to black-and-white, then save back as jpeg file.

How do I make my HP photosmart D1110 Printer wireless for when I print?

How do I make my HP photosmart D1110 Printer wireless for when I print? I mean I dont want to plug my printer up every time I need to print something. I know i can do this with my printer because my uncle had it hooked up this way before he passed away. Now im trying to hook it up again and I cant figure it out.

KristiGilreath wrote:
I tried following the steps but I didn't havesome of the tabs it was talking about. I just dont understand.
Hi,
Which type of connection you want to use ? Which tabs are you talking about ? I could not find full specs of your printer, how old is it ? Do you use a wireless network at home ? As mentioned above, I don't know your existing hardware therefore you need to check the book and select a suitable connection first.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

How do I make my HP PhotoSmart 3210 printer wireless Network

How do I make my HP PhotoSmart 3210 printer wireless. It has an Ethernet port which works fine but I want to print on my current wireless network. Can you use any wireless router of G or N? What else can I use? I'm looking for the cheapest option. Also, It has bluetooth, can I use any USB bluetooth for that to work.? I would rather use my network but if all else fails bluetooth will have to due
I am currently runnning windows 7 if it matter. But, I don't think it does.

Hi,
Buy a new wireless printer could be much cheaper and no headache. Or you can try something like this:
https://www.google.com.au/search?q=usb+wireless+print+server&hl=en&tbo=u&rlz=1G1GGLQ_ENAU282&source=...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

How do I make a 20 X 30 print with layers of 16 X 20, 12 X 18, 11 X 14, 8 X 12, 8 X 10, 5 X 7 and 4 X 6 of the same image to display the different sizes available to someone? Using Elements 13 with Windows 8.1

How do I make a 20 X 30 print with layers of 16 X 20, 12 X 18, 11 X 14, 8 X 12, 8 X 10, 5 X 7 and 4 X 6 of the same image to display the different sizes available to someone? Using Elements 13 with Windows 8.1
A senior citizen needs some help.
Thanks

Saving each image as different size - is it an option for you? I would save images with their name as: 20x30.png, 16x20.png etc etc.
Or explain whether you want these in a webpage in which case only one image is necessary and different sizes are displayed with good CSS code. this is question for Dreamweaver forum if this is what you want.

How can I make US letter the default print size in PSE12

How can I make US letter the default print size in PSE12

Clips from JVC Everio camcorders have always had this problem with Premiere Elements (all versions). You need to select Interpret Footage.
See this FAQ from PE version 2, step 3. Like I said it has been this way with all versions:
http://www.adobeforums.com/webx/.3bc1265c
You might be able to use this tool to change the header of your MOD files so they are seen as 16:9: http://www.videohelp.com/tools/DVDPatcher
Or use this program (SDCopy) to download the video's from the cam, it will allow you to copy straight from the cam to your PC and auto renames and corrects the aspect ratio.
http://zyvid.com/smf/index.php?action=dlattach;topic=280.0;id=153

How can I make my Mac Book Pro print to a Panasonic KX-MB772?

How can I make my Mac Book Pro OSX 6.8 talk to a Panasonic KX-MB772 printer?

You can't. The KX-MB722 is one of the few remaining printers in the class of devices called "Windows Printers" that has no on-board printing software -- it relies on a host computer to provide all of the software functionality and Panasonic only provides such software for certain versions of Microsoft Windows. In this case, it means a 32-bit version of Microsoft Windows (2000-XP, though it will probably reliably on Windows versions up to 7). Note that these devices are not guaranteed compatible with future versions of Windows either (Panasonic has already dropped software support for this model).
I'm pretty sure that the device doesn't support remote printing without the software either (e.g., you can't setup a computer with Windows on it, share the printer, and then print to the shared printer without their software).

Win 7 laptop and Deskjet 6980 Printer don't connect wirelessly

Hi,
I installed the Windows driver for the HP 6980 printer. The printer shows as being "offline" in Windows control panel. The printer network light and wireless status light are on. I ran the HP Home network Diagnostic Utility and it tells me:
1. HP software required to connect to the printer is not installed
and then from the "advanced" tab it tells me further that
2. The HP Service SLP is not installed
3. HP service hpqcxs08 is not installed
4. HP service device discovery is not installed
So, how do I get these things installed?? Where do I get them?
Is this really the problem or is there something else going on?
I have Verizon FIOS and an Actiontec router. Do I need to give the printer a static IP address (as suggested by the HP install manual)??
Any suggestions/advice much appreciated.

Hi,
Is the printer connected to your wireless network?
A solid blue light indicate a proper connection.
If it is blinking it means the printer is disconnected from your network, temporary plug a USB and go to Applications > Hewlett-Packard > Device Utilities. Follow the HP Setup Assistant to reconfigure the wireless connection.
If the printer appear as connected please clarify your router brand and model in order to better understand the problem.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

How can i make the Master data extractor to delta enable

Hi,
I am working on 0EQUIPMENT_ATTR(Master data).
I want to load the data to ODS,
By default SAP has not provided delta for this Object.
can anybody know how to make this 0EQUIPMENT_ATTR to delta enable.
or any other solution.
its urgent..
help me
Madhu

Hi dear and welcome on board !
If a std datasource is not available in delta mode, you cannot change it in order to deliver a delta...if you consider your requirement absolutely necessary, you can go for a generic datasource (RSO2) and try to set a generica delta...
Hope it helps!
Bye,
Roberto
...please don't forget to reward the answers...it's THE way to say thanks here...

I HAVE TWO SHORT CUTS TO FIREFOX?HOW DO I MAKE EACH OPEN TO A DIFFERENT WEB SITE

On my Dell Dock I have two shortcuts for Firefox. One used to open automatically to my email account and the other to Firefox Home page (Google). Now they both open to my email account.
I can switch from one to the other but how do I get them to open to different sites

Creating a Desktop Shortcut to a web page
* https://support.mozilla.com/en-US/kb/Creating%20a%20desktop%20shortcut%20to%20a%20web%20page
Check and tell if its working.

I have a e printer and thee printer is on the same wifi net work as the iPad, when I select print from the iPad the response is no printers. I can successfully email from my iPad to the printer. How can I make my iPad recognize the printer?

I have an e printer and the printer is on the same network as the iPad. When I attempt to print from the iPad I get a message no printers available. How can I get my iPad to recognize the e printer?

This printer has worked for me with out fail at my house. I am traveling in an RV and am at the mercy of the RV Wifi. I do not have access to the router. The printer has been recycled a number of times as well as the Ipad. The printer is set up and has access to the wifi. It seems to me that the Ipad and Iphone are not recognizing the connection with the e printer. I was hoping there was some adjustment that could be made to the Ipad and Iphone. I can email to the printer from both gadgets. I will try to recycle the devices again.

How can I make my own design for a web page instead of using a template?

Need to ask the question again. I tried using the blank template, but could not get it to work. I could not insert images and copy where I wanted and in size I wanted.

rapcom wrote:
A general question: Is it possible to change the dimensions of the web page? Or even its positioning as a horizontal or vertical format?
Yes — it's done via iWeb Inspector's Page tab (the second one at the top), editing the values in the +Page Size+ fields. After entering a new value, click the Return key to make it take effect...
..By the way, the above image is taken from a tutorial ~ click on the image above to read the tutorial.
rapcom wrote:
I also would prefer to edit the copy on the blank web page, and cannot do that either. Is it possible to do so?
Yes, it's possible. But it's difficult to know what exact difficulty you're having, and I perhaps risk stating the obvious... One thing to be aware of is that clicking once inside a text box will simply select that box (you'll see eight +"grab handles"+ for re-sizing). But to edit the text inside, you need to click once more. Experiment with clicking inside and outside text boxes and you'll learn.
And iWeb's Help menu has several resources ~ the Help viewer, a +Getting Started+ PDF and a link to ten video tutorials. One of the videos briefly demonstrates adding a text box towards the end; click here...
If after the above you still need help, post back with step-by-step details of the problem.

How do you make sure the form data prints (commercial offset printing)?

We are commercial printers and have been using a PDF workflow for quite a while now. We recently received a PDF form to print but any information filled in the form just dropped out (all non-data printed fine). When we send it to a laser printer, everything is there but when it goes through the RIP and imposition software (both Heidelberg), all the data is missing.
When I open the PDF from the client, I am not able to change or even highlight the data. There is a message saying the information is locked.
We were able to get around the problem by importing the PDF into InDesign and making a new PDF from that but that seems to be an extra step that coulb be avoided.
Anyone else with a similar problem (and solution)?

How can you tell that it is an XFA form? If I can identify the form type from when I get jobs like this, I can use the workaround from the beginning.
Here are a few more screen shots of things that are happening:
When I try to Print to a PDF:
When I use the Mac "Save to Adobe PDF" in the print dialog:
I get this message often:
and when I try to embed the missing font (PitStop), I get this:
The only thing that has worked so far is placing the PDF in InDesign and Exporting to a new PDF from there. I guess this is making the flattened PDF that you talked about.

I uploaded pictures to iphoto and they are too small. How do I make them normal size for printing?

The pictures I uploaded from my digital camera are stored in iPhoto and under Photo_data_roll... I am trying to print them, but the quality is very bad because the size of the photos was compressed (or something) when I uploaded them. How do I get the photos to their normal size?

This sounds like it is more likely a problem with your camera. Digital cameras have setting for resolution and amount of compression used. I would start by looking there. If resolution is set low or compression too high, the picture might look okay on a camera's two inch screen but like c**p in iPhoto.

How do I make my HP Deskjet 6980 printer Web Enabled?

Similar Messages

Maybe you are looking for