How do i measure bipolarforAgilent E3631A ?

Hello, i am new in using labview .
Can any one please help me how to measure bipolar Agilent E3631E ?
My goal is to sweep the output of E3631E voltage supply from -25 to 25 V on the I-V plot. Since I already made the i-v curve from 0 to 25V or otherwise, but i could not get it sweep from -25 to 25 V
Ti

Hi Ti
if you already have suceed in sweeping from 0 to 25 v
it should not be a major problem to do the other sweep.
Is your supply floating or grounded !
Remember you have to enable the appropiate supply .
Also your output supply . Set the -25v supply to your negative (ground) connection
and the 25V to your positive supply connection.
If you have further queries don't hesitate.
If need be post a jpg of your working code.
xseadog

Similar Messages

How can I measure the hertz in a wave form?

How can I measure the hertz in a wave form?

As an example, this is from BBC Technical Requirements for HD material:
3.1.1 Stereo line-up tones
All stereo tracks must use EBU 1KHz tone (left ident). All tones must be sinusoidal, free of distortion and phase coherent between channels.
Digital Audio Reference level is defined as 18dB below the maximum coding value (-18dBFS) as per EBU recommended practice R68.
See also:
http://www.bbc.co.uk/guidelines/dq/pdf/tv/tv_delivery_to_network_programmes_v1.2-2011.pdf
for full document.
And for BBC Radio:
Not every Network requires tone. Check the delivery requirements with the commissioning network or click here.
Reference tone, where used, should be at -18dBFS or PPM 4 on A, B and/or M.
If submitting material with reference tone, tone and programme material must be have been monitored and measured through the same technical chain. The level of the tone must be equivalent to 0dBu and no less than 8dB below peak audio level for the programme material.
THE LEVEL OF TONE MUST HAVE A KNOWN RELATIONSHIP WITH THE LEVEL OF THE PROGRAMME MATERIAL AND THIS MUST BE STATED; for example: “Tone at 8dB below peak programme level”.
As a newcomer to digital sound (my background is camera) I confess to being somewhat confused. We are normally told to record at the highest level possible. So for voice podcasts I tend to record at about -6dB below peak for maximum volume, distributeds on MP3 files.
But I can underatand that televison and radio especially for analogue transmission) may have limited headroom, hence the requirement for -18dB peak = 0dBM.
I remember when we first rented out Digital Betacam cameras, some recordists were recording almost everything OVER -18dBM.
I suspect that until we have an all-digital world, these requiremnents will still be in place.
Many thanks to all. It's a ghreat community!
Brian Rose

How do you measure a Cycle's lenght in time, not bars and beats?

How to you measure the time length on a selected cycle ? I understand that when any cycle is selected, you can see the length of that specific range on Bars and beats, but not in Real time. How do I get to see ( Calculate ) the real time length of a cycle range? When working with video this feature is absolutely necessary. ProTools shows you the length in time when a cycle range is selected. I also know that you can calculate the distance of any given point in the song, relative to the start time, you can see it in the Time Position display, but what If I need a more exact time calculation ( min:sec:frames, etc. ) between two specific cue points that are only relevant to video sync, not relative to the start time and not relative to musical values. Like if I need the exact time length for a video cue, etc.

Thank you, very Much, That's it !!!
I've looked for that for years...LOL, It never occurred to me to look for a "negative",
Awesome
J

How to put measures correctly into spreadsheet

Hi expert,
I loaded data into a planning model, and I can see data in BW and BEX, but when I put 'ACCOUNT' into row, and 'TIME' into column, I can't see 'measures' in spreadsheet, eventhough I drag 'measures' into spreadsheet from EPM pane, then update, getting blank for 'measures', it is gone. please tell me how to put measures correctly into spreadsheet.

P.S If you are creating report by drag n drop on EPM pan, then same way need to add measure dimension in desired axis.
Share the screen shot.
Shrikant

How to use Measurement studio math lib in VC6

dear sir,
I get the evolution version of measurement studio, which works well in DotNet and I confront with the problem that i do not know how to use measurement studio math library in VC6, please help me out ?

All versions of Measurement Studio released to date include support for Visual C++ 6.0 (and Visual Basic 6.0).
This support is on a separate CD from the support for Visual Studio 2003 and Visual Studio 2005.
For example, the Measurement Studio 8.0.1 kit includes 5 CDs. One CD includes support for Visual Studio 2003 and 2005. Another CD includes support for Visual Studio 6. The other 3 CDs are Device Driver CDs.
You want to use the CD that includes support for Visual Studio 6.0. This CD contains 2 installers. First run Setup.exe. Then run MeasurementStudio6Updater.exe to get the latest components. See UpdaterReadme.htm for information on what components are updated by MeasurementStudio6Updater.exe.

How can I measure the Graphics Card usage? I.e. percent load

Hello,
How can I measure the Graphics Card usage, like with the processor in Task Manager, but instead giving a percentage usage for the graphics card instead? Is there an easy way to do this, or would it require a lot of code? Is it even possible?

Ah, so It's unlikely that Java3D will include anything for reading this data then? I was really aiming at measuring the GPU usage under this API which although i have limited knowledge using, I do at least have some knowledge - I wouldn't have a clue how to access any other API's!
I'm using an NVidia TNT2 card at the moment, which is quite old.

How do u measure the size of the infocube?

hai gurus
1) how do u measure the size of the infocube?
2) what r the asap methodolagies?
thanks in advance
rams

hi Rams,
1. use transaction se16, infocube table /../f[infocube name] and /.../e[infocube name], count 'number of entries' - total records
use transaction db02 tablename infocubename - size in bytes
Re: how can we measure the info cube size
2. asap methodology
Re: Lifecycle Implementation
hope this helps.

How can I measure the thickness of a circle line?

Hi,
we try to measure the thickness of a circle line to find out if the circle is round or if there is any deviation in the circle. By now we are using the FindEdges tool and measure the circle at different points.but this is not sufficient.
Does anyone has an idea how we can measure the thickness of the line of a circle?
thanks
Oliver

Hi,
yes I have two pictures.
Picture 1 is the original, Picture 2 is the "working picture"
greetings
Oliver
Attachments:
Picture1.zip ‏243 KB
Picture2.zip ‏5 KB

How can i measure SNR(S/N)value using FSP Spectrum analyser

hi ,
I want to measure S/N value using spectrum analyser.i already installed rsspecan instrument driver.I also configured span,center frequency ,RBW,VBW etc but i am not able to get measured S/N value.I have attached my vi here with.how could i measure SNR Ratio??can you please help me!
thanks.
Tadhika
Attachments:
Unbenannt 1.vi ‏77 KB

Hi, first of all I'd recommend to contact the R&S customer support center to be shure the measure the correct value. Did you really measure the actual noise, or do you measure the noise which is "only" displayed?
But anyway, did you have had a look at this example: http://www2.rohde-schwarz.com/file/rsspecan_lv8_noise_marker_example.zip
There is the setup of one noise marker shown. With your already existing marker value this should do the trick, also in case of two noise markers; just use the rsspecan Configure Marker Noise Measurement.vi again with input parameter <YourMarker+1> of the "Marker" input of the VI.
Hope that helps?
juergen

How can I measure TREX server.

Hi,
I'm from Nakisa forum as below.
<How can I calc sizing of TREX server
I'd like to install minimum TREX server for Nakisa.
A document of nakisa is written about nakisa server but it isn't written trex server.
<https://websmp209.sap-ag.de/~form/sapnet?_SHORTKEY=01100035870000728933&_SCENARIO=01100035870000000202&>
I found SAP note 1266024 which is written about sizing guide line of Nakisa but it's so difficult to calc.
How can I measure TREX server and which minimun sizing is best to use Nakisa?
Hope you can help us.
Best regards,
Makoto

Hi Makoto,
try the infos for TREX under http://service.sap.com/sizing.
They are not made for Nakisa. But I am sure you will be able to roughly map them to your use case.
best, Karsten

How can I measure memory allocation of a Java Application?

We built a web application that enables images to be loaded into a database through a servlet running on Tomcat. We have inconsistent behaivor when more than x number of people are loading images simultaneously. No doubt a memory allocation problem, but how can I measure it?
For example, I'd like to be able to create a graph showing the resources used against the number of people making uploads. I am using Linux and Tomcat/Apache.
I am hoping for something like Memory counters that are available for measurine Windows applications on MS Windows - comes with the Resource Kit. Does this type of tool exist for the Java/Linux market?

It is difficult to gauge memory usage from a Java application as the JVM handles garbage collection and even if objects are not referenced they might still be sitting in memory until the next garbage collect.
Anyhow, a way to query available memory is:
Runtime.getRuntime().freeMemory()
You can run this at the begining of a process and at the end and examine the difference. You should call System.gc() before each freeMemory() call in order to try to force garbage collection.
Another method would be to turn to the underlying OS. On linux you could use 'top' or 'ps'. With ps you could do something like:
ps -o rss,vsz,%mem <pid>
Where <pid> is the parent Tomcat process' id. The resulting three columns are:
- Amount of real memory used.
- Amount of virtual memory used.
- Percentage of real memory used.
'man ps' wil give you more options on how to use ps.
There are also fancy graphical stuff like 'gtop' as well.
Hope this helps.

How can I measure how much Data I am using?

As the headline say:-
How can I measure how much data I am using?
Thanks in advance.

Not a problem at all - without wishing to push the point at all, the manual really is very good and worth a read ! although I must admit I have never read it all
http://manuals.info.apple.com/en/iphoneuserguide.pdf

How can i measure distance ?

i am making afire fighting robot that us camera to detect the fire i made the vi which find the fire through match pattern but now i want to measure the distance between the camera (which on th robot ) and the fire (which located in the image using match pattern) so how can i measure this distance?
khaledyr

Ok... this is sad, I should be asleep now instead I'm here thinking about this problem.
I've worked out how to do the distance caluclation with no extra H/W and only 1 camera - as Henrik said, the standard solution is triangulation, but you just want to measure distance, so I'm going to assume you're already pointing in the right direction.
Assumptions:
1) It is usual to use triangulation to to measure intenisity, this is because light will have 2 different distances to travel from source to sink.
2) It is possible to use 1 sink if you use mirrors to increase the path of the light so you can have 2 seperate source -> sink distances.
3) having 2 cameras (sinks) next to each other, one covered with a physical filter would have the same effect as the amount of light reaching the 2 sinks from the source will be different.
... following on from 3, it can be assumed that taking 1 image and applying 2 levels of filtering to it before processing will give the same result as if we had 2 different images. Careful setting of the software filter level will then allow it to remain contstant and then the system can be calibrated just as any other system would be calibrated:
Measure the intensity of the source from sink A at distance X
Measure the intensity of the source from sink B at distance X
Measure the intensity of the source from sink A at distance Y
Measure the intensity of the source from sink B at distance Y
If Y=2X the calibration calulation is easy....
Hope this provides more food for thought.
James
P.S. Lynn - currently a firefighter and worked for the emergency services ehh? Always good to see your posts when you have something to add. (Firefighter / Software programmer - what's the difference?)
Message Edited by James W on 04-22-2010 10:56 PM
Message Edited by James W on 04-22-2010 10:56 PM

How can i measure the speed of the fan in sound and vibration signal simulator box

how can i measure the speed of the fan in sound and vibration signal simulator box
provided the values tach out:2 pulses/revolution and maximum speed = 6000rpm

Hi. I tried your suggestion and I could not get it to work well. In
fact it worked better without the running average (which suprised me).
I also played with the number of data points but still could not get it
to work well.
Do you have any other suggestions on how I could sort this problem out?
I
have attached a screen shot of the signal. To recap, I'm trying to
measure the'y' position of the flat regions of the signal. The signal
does not have a constant level, so this 'y' position varies with time
in a non-unform manner.
I am currently differentiating
the signal and selecting the y position when the differential is equal
to zero (within a tolerance band).
In the screenshot, the
signal has been zeroed using the method I have described above.
However, it occasionally has glitches which may be caused when the code
picks up a zero gradient at a peak or valley in the signal.
I therefore need some kind of algorithm that only measures the position of the flat regions.
Many thanks
John
Attachments:
screenshot.gif ‏121 KB

How can I measure selected area of pixels using photoshop elements 12?

how can I measure selected area of pixels using photoshop elements 12?

Show the 'information' panel F8).
In the middle horizontal section, select 'pixels' on the left drop-down menu.
Use the rectangular marquee tool to select your area: the dimensions in pixels of the rectangle is shown under 'dimensions' on the right.
I think there are other ways to measure a line segment, but you could use the above measure by adjusting the rectangular marquee tools to both extremities of the segment,
- use the move tool to rotate the rectangle so that the diagonal measuring the segment is horizontal,
- move the rectangle to the left, and check validate, which creates another rectangle including the first one
- read the pixel dimension (L:) in the info panel like above.

How do i measure bipolarforAgilent E3631A ?

Similar Messages

Maybe you are looking for