How do I physically fit memory into Equium M70-337?

Hello,
I am in the process of buying a memory upgrade for my Equium M70-337.
However I am unsure how to actually fit it.
I have unscrewed the memory panel and stared at it not really knowing what to do.
Any advice, any links to diagrams would also be highly useful.
Thanks for any help.

Hi
First of all before you install or remove a module, turn off the computer with the shut down option in the windows. The notebook shouldnt be in the standby or hibernation mode because you would lose the data.
Some memory modules can be physically installed but are not fully compatible with the notebook. In this case the machine will issue a warning like 3 short beeps.
Here a short instruction how to fin the modules;
- Turn the notebook upside down (dont forget to disconnect all cables) and remove the battery.
- Remove one screw securing the memory modules socket cover
- Slide your fingernail or a thin object under the cover and lift it off
- Fit the modules connectors into the computer connectors at about a 45degree angle and press the modules careful to ensure a firm connection.
- Push the module down so it lies flat. Latches on either side will lick into place to secure the modules.
But note; do this carefully and dont use any force!
Bye

Similar Messages

Equium M70-337 Memory Card Reader

Can anyone help me. My memory card reader used to work until the laptop crashed and was fixed now it won't show yup on my computer so therefore cant get pictures off of my camera. Havc

Hi pwashford,
Im glad to hear that and thank you for this feedback!
From my own experience I can also say that updating the card reader driver is solving the problem. :)

Equium M70-337- which hard drive can I fit in this laptop?

Hi, will it just be a 2.5 inch sata? Thanks for any help

Hi homervanderjazz_1,
I agree with PauPau. Your notebook supports 2.5 SATA drives. So you can install every 2.5 HDD with SATA interface.
500GB or higher capacity should be no problem because its SATA :)

Battery would not charge on Equium M70-337

I can run my laptop from mains power but the battery won't charge anymore. It's been like this for a while and i haven't really looked into it yet.... but i think i may have deleted one of the programs that charges the battery a while back... stupid, i know. I still have toshiba power saver, but seem to remember there was a second charging icon that used to come up in the bottom right corner that i may have thought i didn't need. Any ideas how to get it back? Would appreciate any help. Thanks.

Hi there,
dont worry, usually it should not depend on software if the battery charges or not. But to go the secure way, I suggest you at first to re-insert the battery.
Battery should usually charge any time, no matter if windows is loaded or not. So, if not, then you have a power-related problem.
Just try this re-inserting and if this does not help, contact a technician (if you know someone) or a authorized service partner.
It can be, that you have a serious hardware problem.
Heres a link if you search one:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT
Greets

Equium M70-337 won't boot up

Hi,
This unit had been working ok.
It came up saying the battery needed charging, so the power supply was attatched, but nothing happened.
Now the battery is flat and the unit won't come on even with the power supply connected.
I have checked the output of the power supply and that appears to be ok.
Is it likely that it's just the DC barrel connector on the laptop, or is this a more serious issue?
Regards,
Nigel.

Hi
Possibly my advice could help you;
Try this:
- remove battery and disconnect the AC adapter
- wait about ~20-30min
- connect both parts again (battery & AC)
- try to boot up the machine
If this will not help then its a serious issue and the local ASP is your last resort.
Good luck

Excessively High CPU usage on my Equium M70

HI,
Recently in the last month my CPU usage as been hitting 100% when Im not running any taxing software (just internet explorer and windows media player).
This is slowing down loading times and the area near the fan is pretty hot.
I have an Equium M70-337, with a 1.7 centrino processor, and now 2 gigs of RAM (formerly 512 megabytes). I upgraded the ram in December and had no problem like this, now it's just started happening recently, I haven't installed anything that would do it, there are no unnecessary programs running and this was after I restored my comp to factory settings with the startup disc (about a month after) so it seems to have come from nowhere. On the task manager list it shows my web browser and media player using up the majority of CPU but I could have sworn that they didn't use up this much before.
I don't know if the RAM would have been a factor but it was the correct ram for it and windows acknowledged to 2 gigs.
Why would this have happened suddenly, any ideas guys?

Hi
I have the same notebook model and at the moment I do not have such problems. To be honest I have made clean OS installation 3 months ago and after Microsoft update installation I have noticed that notebook does not run like before. Just for example: if I use IE7 intensively with several different tabs in task manager I can see that IE need over 300.000 k of memory and somehow blocks. After closing IE and ending the IE process sin task manager I can work normally again.
I really do not know how is your OS configured but in task manager you should see which running process is responsible for high CPU usage. Maybe some antivir application? Sorry but on this way it is really not easy to sayt why this happen. Play little bit with running processes.

Recovery disc for Equium M70 needed

I have tried to recover my Equium M70-337 using the product recovery cd that was shipped with it, but this is corrupt and I now have a blank laptop.
Where can I get a new recovery disc from? The laptop is too old for me to be able to order one from Toshiba.
Any help would be greatly appreciated.

This notebook model is too old and you will probably not be able to order new recovery disc.
What you can try is to contact nearest Toshiba service and ask if they have one that can borrow you for testing purposes.
You can also use Microsoft WXP installation disc for OS installation. All necessary drivers you can find on Toshiba download page so you don't need recovery disc.
If you need some help about it let me know.

How do I install memory into the Pavilion 17z-F2 series laptops?

How do I install memory into the Pavilion 17z-F (17z-F200, product L2H13AV) series laptops?
HP appears to have no maintenance guide available for this model series. What's up with that?
Please, do not offer the generic (and out-of-date) Pavilion 17 Notebook PC Maintenance and Service Guide. It does not appear to apply to the 17z-F series. This guide instructs to remove the bottom service panel which I could have figured that out on my own. However, the 17z-F series does not appear to have any removable panels at all. I took an up-close look at the Pavilion 17z-F100. And, it does not have any removable panels on the underside, except for the battery. So, I presume the 17z-F200 to be the same.
I am a computer technician. And, this is the first laptop I have seen without any service panels. I am probably going to have to disassemble the entire outer-shell to install memory (or to replace the hard disk drive once the time comes). But, every laptop I have worked on in the past had its own special array of hidden screws or special tricks for disassembly. So, having a maintenance guide is a necessity to avoid damaging plastic mounts, clips, guides, etc.
This question was solved.
View Solution.

How about this one:
Pavilion 17z Manual
Don't get me started on this. It's one of my pet peeves, too. HP is not the only one doing this. Acer and Toshiba, etc. also are selling "closed" systems now. I hate it. I will absolutely never knowingly buy one but I am spending a lot of time here answering questions just like this. Good luck and let us know how you do. Sounds like you will be fine.
If this is "the Answer" please click "Accept as Solution" to help others find it.

How do I install memory into the Pavilion 17z-F200 (part L2H13AV)

How do I install memory into the Pavilion 17z-F200 (part L2H13AV)?
HP appears to have no maintenance guide available for this model. What's up with that?
I took a look at the Pavilion 17z-F100 (sent by mistake). It does not have any removable panels on the underside. And, the User Guide for the 17z-F200 indicates that it will be the same (assuming it ever arrives).
I am probably going to have to disassemble the entire outer-shell to install memory (or replace the hard disk drive, once the time comes). But, every laptop I have worked on in the past has had its own special place for hidden screws or special trick to disassembly. So, having a maintenance guide is a necessity to avoid damaging plastic mounts, clips, guides, etc.
This question was solved.
View Solution.

@DLBurkhart ,
Hello and thank you for posting on the HP support forums. Here is a link to the HP Pavilion 17 notebook Maintenance and service guide.
HP Pavilion 17 Notebook PC Maintenance and Service Guide
In the guide you will find the instructions on how to access the memory module and as well you should find the supported memory configurations.
I hope this was helpful.
Thank you for posting and have a great day
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

How to import pictures from an external memory into Iphoto?

How to import pictures from an external memory into Iphoto. Is there a way to open all the pictures in my computer in the Iphoto?

to import photos either use the iPhoto file menu ==> import command or drag the photos to the iPhoto icon in the dock
LN

How to fit SSD into my laptop?

I have an SSD. I want to get it into my laptop. I have a Pavillion DV6 3216-us, and I also have an SSD, can't find it on google, but it has a internal half-mini PCI-e connection. I don't really know how I am supposed to get this into my laptop, as I can't seem to find a adapter to make it SATA to replace my current hard drive. If you guys could help me out, I would appreciate it. Also, I'm not too good with these things, like the adapters and compatibility between things. Thanks.

hayd3nd wrote:
I have an SSD. I want to get it into my laptop. I have a Pavillion DV6 3216-us, and I also have an SSD, can't find it on google, but it has a internal half-mini PCI-e connection. I don't really know how I am supposed to get this into my laptop, as I can't seem to find a adapter to make it SATA to replace my current hard drive. If you guys could help me out, I would appreciate it. Also, I'm not too good with these things, like the adapters and compatibility between things. Thanks.
This kind of solid state drive is not compatible with the laptop. Even if you can fit it into an adapter (haven't found any), the BIOS may not to detect it. Sell the ssd and buy a typical SATA II one..
Dv6-7000 /Full HD/Core i5-3360M/GF 650M/Corsair 8GB/Intel 7260AC/Samsung Pro 256GB
Testing - HP 15-p000
HP Touchpad provided by HP
Currently on Debian Wheeze
*Please, help other users with the same issue by marking your solved topics as "Accept as Solution"*

How to get physical memory by using system call ?

how to get physical memory by using system call ?What system call can I use.thanks

Use sysconf(3C) with SCPHYS_PAGES

How to reimport relational table objects into RPD physical layer...

I am new to OBIEE. I am not sure how to reimport relational database tables into physical layer whenever the base database table structure changes.
How do I configure the ODBC or OCI 10G/11G connections on my computer so I can reimport objects into RPD on remote server.
I would appreciate it if you can give step by step instructions
Thanks in advance.

Hello -
You can re-import a table to the Physical Layer the exact same way that you would import the table for the first time:
1) Click File > Import > From Database...
2) Select your data source connections
3) Choose your table you wish to reimport
The system will warn you that you will overwrite the existing table and may lose information. The information you would lose is any discrepencies in the physical layer that are no longer existing in the actual database table. However, logical columns will NOT be overwritten.
Alternately, if it is a minor change to the table (say a column name change, or one additional column added), you can also manually add the column
1) Right Click on the already imported table in the presentation layer and select New Object > Physical Column...
2) Name the column and provide the proper data type
The column now exists in the physical layer and will be properly associated with the new column in the database, assuming the same column name was attributed. You WILL have to drag this new column forward to the logical layer and presentation layer, as this will not be automatically done.
I hope this answers your question. If you found this helpful, please assign points!
Regards,
Jason

How to make ul fit into the holding div

i am encountering two problems here..
1. The <ul> does not fit vertically into the holding div
2. The <li> elements are indented i need them to be flush with the left margin
www.ebn-tec.co.za
The bottom div on the FEATURED WORKSHOP

Undoubtedly, others that are junior to my person, will understand exactly what you are referring to. But in case others do not reply here, do you mind explaining the problem so that I can see it.
For instance, I do not see the FEATURED WORKSHOP
By voorbaat my dank

How can I get my picture into the window to fit correctly?

Hello,
I'm somewhat of a novice, so please bear with me. I am editing a sequence together that has footage from multiple camera sources. Some of the footage is at 24.00 fps, some at 29.97, some at 23.976.
When I'm looking at the window to see my footage, some of the footage fits completely in the window, and the other half is getting chopped off, so I can only see 1/3 of the image. I divided my footage in half into two different sequences, and the footage looks great, nothing getting chopped off. But, as soon as I combine all of the footage into one sequence, something is getting chopped off.
What is happening? Both of my sequences are set to 23.96. So, theoretically, they should look the same in either sequence, correct?
I just want all of my footage to fit correctly into one sequence so I can see the entire picture of each clip.
Thank you so much,
Nicole

I would suggest you work out which footage is the "smaller dimension". (pixel x pixel resolution)
Create a Sequence that matches that
What may help is to click the NEW ITEM link on page #5 of The PPro/Encore tutorial list http://forums.adobe.com/message/2276578
...and copy and paste the other footage into using the Scale to Frame size option.

How do I physically fit memory into Equium M70-337?

Similar Messages

Maybe you are looking for