How do I remove the repetitive Utility error.

I have a repetitive Utility error on macbook that flags every 10 minutes. I then have to either open console or terminate. How do i prevent the constant pop up.

This is happening all the time on my IMAC. Does anyone know how can I get rid of it.

Similar Messages

How can I remove the repetitive multiple daily updates from Mozilla

Hello
How can I remove the repetitive multiple daily updates from Mozilla?
Within a day, each day I get prompts as: Mozilla Firefox Update is ready to install at your computer.........then I do install and update it.......then after few minutes again it asks to update the same edition.........again after logging in back few hours later it prompts me again with the same request........IT IS VERY ANNOYING!
Thank You,
Gene

''the-edmeister [[#answer-683804|said]]''
<blockquote>
You could allow the update to proceed - that will stop Mozilla from asking if you want to update every time you launch Firefox, as is supposed to happen.
Any particular reason that you don't want Firefox 35.0.1 to be installed?
</blockquote>
Hi The EDmeister,
Thank you for your response.
Nevertheless, I have to repeat that I have ALREADY INSTALLED the Firefox 35.0.1 in my computer and ALLOWED IT TO PROCEED.
The same edition is prompting me back again, and again and again, within a day, each day. I get that annoying message at the top-right hand.
I do not want to see it every time, multiple times a day, that is the issue here, unresolved!
Best regards,
Gene

APAgent.exe error dnssd.dll on startup with the suggestion to reinstall. How do I remove the error?

I am giving away my windows XP laptop to my 80 year old Mom and deleted itunes and ipod software.
Now getting APAgent.exe error dnssd.dll with the suggestion to reinstall. How do I remove the error? I don't want to reinstall on this laptop.

Did you uninstall Bonjour from the PC? Airport software uses Bonjour, and it looks like your Airport base station agent is complaining about the missing Bonjour (dnssd.dll is a Bonjour file).
Is your Mom going to be using the Airport capabilities of the laptop? If not, it might be easiest just to uninstall the Airport utility and/or other related Airport software.

How do i remove the 17 errors that come with the pricing userexit manual at

how do i remove the 17 errors that come with the pricing userexit manual attached code...

Try connecting the phone to the computer in "data storage" or "data transfer" mode, then open the memory card folder in Windows Explorer, and search the sounds there. If you can't see them, go to "Tools>Folder Options>View>Files and Folders>Hidden files and folders" and select "Show hidden files and folders". But I think that it would be a lot easyer just to remove them from the playlist manualy.
Crossing bridges far ahead of the crowd.

So I downloaded the wrong Airplane Mode program for my operating system and I now have AppleScript Error message. It will not allow me to quit the program. Also, once that happens how do I remove the program from the computer?

So I downloaded the wrong Airplane Mode program for my operating system and I now have AppleScript Error message. It will not allow me to quit the program. Also, once that happens how do I remove the program from the computer?

What Airplane Mode program? To stop a running program launch Activity Monitor (in utilities folder) and quit the program from there. To remove the program drag it to the trash or better use the uninstaller that should have come with it.

How can I remove the Demo Viewer from my MacBook?

How can I remove the Demo Viewer from my MacBook?

Drag it to the Trash.
Uninstalling Software: The Basics
Most OS X applications are completely self-contained "packages" that can be uninstalled by simply dragging the application to the Trash. Applications may create preference files that are stored in the /Home/Library/Preferences/ folder. Although they do nothing once you delete the associated application, they do take up some disk space. If you want you can look for them in the above location and delete them, too.
Some applications may install an uninstaller program that can be used to remove the application. In some cases the uninstaller may be part of the application's installer, and is invoked by clicking on a Customize button that will appear during the install process.
Some applications may install components in the /Home/Library/Applications Support/ folder. You can also check there to see if the application has created a folder. You can also delete the folder that's in the Applications Support folder. Again, they don't do anything but take up disk space once the application is trashed.
Some applications may install a startupitem or a Log In item. Startupitems are usually installed in the /Library/StartupItems/ folder and less often in the /Home/Library/StartupItems/ folder. Log In Items are set in the Accounts preferences. Open System Preferences, click on the Accounts icon, then click on the LogIn Items tab. Locate the item in the list for the application you want to remove and click on the "-" button to delete it from the list.
Some software use startup daemons or agents that are a new feature of the OS. Look for them in /Library/LaunchAgents/ and /Library/LaunchDaemons/ or in /Home/Library/LaunchAgents/.
If an application installs any other files the best way to track them down is to do a Finder search using the application name or the developer name as the search term. Unfortunately Spotlight will not look in certain folders by default. You can modify Spotlight's behavior or use a third-party search utility, EasyFind, instead.
Some applications install a receipt in the /Library/Receipts/ folder. Usually with the same name as the program or the developer. The item generally has a ".pkg" extension. Be sure you also delete this item as some programs use it to determine if it's already installed.
There are many utilities that can uninstall applications. Here is a selection:
    1. AppZapper
    2. AppDelete
    3. Automaton
    4. Hazel
    5. AppCleaner
    6. CleanApp
    7. iTrash
    8. Amnesia
    9. Uninstaller
10. Spring Cleaning
For more information visit The XLab FAQs and read the FAQ on removing software.

Photosmart 8230. How do you Remove the print heads for cleaning?

Hi guys, I have a Photosmart 8230. After a few lines of printing the black ink fades to almost nothing, all the colours are perfect. There are no error messages. I have done the self cleaning and alignment procedures and wasted a lot of expensive ink. The test page comes out with streaks on the black only. It has been suggested that I take the print head out and immerse it in hot water as a last resort. The question is, how do I remove the printhead? or should I use it as a sea anchor!!
This question was solved.
View Solution.

I just did this to a HP Photosmart 8250 which is in the 8000 series range. I assume they are similar. I was an appliance repair man and have done a lot of other tings in my life, so I decided to take a shot at repairing my 8250 rather than junk it. For 3 Years it was great, only one paper jam, and fast great photos, so I didn't want to give up on it. HP will not repair printers for us, I think because it is too labor intensive, and they can sell a new one for what it would cost.
I actually fixed my HP Photostat 8250. Its working but the color printing is not as good as it was, yet, but I am hoping that will improve as all of the colored inks work their way through the system.
Taking one of these apart and putting it back together is like a Chinese puzzle, so its appropriate that they are made in China. Most of the parts inside can be easily damaged if you are not careful. The covers have very clever ideas to their design and how they snap in place. Take your time with the covers and use small tools.
Getting it back in working condition is another matter. There is a 6 circuit pump and more than a few feet of tubing. I had the side covers off while I tested it and this pump seems to work in both directions. This pump is inside the left side cover. There is another motor with a timing wheel of some kind that stops and starts in both directions at the same time the printhead carriage is whipping back and forth printing. There are other motors also. These things are ingenious. It is surprising that I bought it for less than $100 on sale. It looks like a $1000 piece of equipment inside.
It would probably be a good idea to not remove the left side cover, but if you do, be very careful around the clear timing wheel. it looks delicate. Below is from an email I sent to a friend and I am revising it to make sense. Remember this is something that really requires training to do this, but I see people today that have the guts to tackle all sorts of projects, so for what its worth, and you asked.
Under the right side cover is a motherboard, with a bunch of cables plugged into it, small, larger and even ribbon cables. I found it necessary to remove the motherboard. I had a bit of experience working on Canon printers and I would also suggest you take digital pictures as you go so you can view them on your PC. I am also going through this because I don't like being told we can get anything repaired correctly today, its ridiculous that these printers have become just more throwaways. If you want to do this, as a guide, I must have spent 8 to 10 hours doing this, but now I could do it again in 2, that is the learning process.
Once you get the top off the printer, you will see the printhead carriage. The carriage will be to the right side. The printhead is retained by two screws at the front, (take pictures) a spring clip at the rear and two screws that hold a plastic cover over the six ink hoses that plug into the printhead, its a manifold strip affair. You have to unplug the manifold to remove the printhead, but now I am not 100% sure its necessary to remove the printhead? The ink gunk you will see after you move the printhead to the left is no doubt most of the problem.
Probably after the hot water treatment as described below, the built in printhead cleaner will be able to resume cleaning the printhead, after the hot water cleans the gunk from IT.
I removed the printhead like I say below, but first do this. Under the printhead there is a little carriage with a patch of foam rubber that cleans the print head nozzles.This little device works back and forth while cleaning, but while it is parked, with the printer off, it is forward and you won't be able to move the printhead. Use a flashlight to be sure and you will see how to push the cleaner carriage to the rear and then move the printhead carriage to the left. THEN, you will see the gunky ink mess that has accumulated. This gunky mess I think is the main problem. There are also some felt pads below the cleaning device to absorb some of the ink gunk. I don't know how the HP techs do this, but I used the hot water method below, I had nothing to lose. I would move the printhead first and then you can decide about removing it. I would make sure not to get any of the electronics wet and why I removed the motherboard and why I say take photos. Its hard enough to remember where the different screws alone go, when you are doing this. It can be done, mine is working, even if not perfectly, YET. You need to be very careful with your fingers, because it is hard to find space to hold onto the printer and whay it might be a good idea to not remove the left side.
They are so complicated, its just a matter of time before they get gunked up with ink and the printhead begins floating in the mess. I had nothing to lose so I removed the printhead, carefully, taped up all the hoses so they didn't dry out, Then I removed the motherboard to keep it from getting wet, THEN I held the messy ink end under the HOT water in the laundry tub and flushed out enough ink to dye a bathtub full of water. The hot water worked well. Then I let it all dry out. There are some delicate procedures to all of this and it takes time. I think that is why its very hard to find anyone to fix them. Its labor intensive and probably why HP won't repair them. The print section is the problem, and why I won't buy an All in One printer, Fax, and Scanner. I do buy the extended warranty's now. If you tackle this, take your time, take photos, and good luck. By the way, the 8250 uses O2 print cartridges, is that the type of printer you have, but a lot of this applies to other printers and other brands, and I bet I am not the only one to do this. Before I started this the diagonstics showed no problems, so I assumed it was the the ink aspect of the printer, and not an electronic of mechanical problem. I hope this helps.
----- Original Message -----

How do I remove the Skype Translator preview!?

Hi.
So hard to even find where to submit a question!
Please help. I just want to uninstall! No entries found in add remove programs. How do I remove the translator preview!?
I'm now using skype for my new postion and I can't affort to be a part of the translator preview. It's affecting my system stability. System is acting wonky and I'm getting many entries in my system log:
Log Name: Application
Source: Microsoft-Windows-Immersive-Shell
Date: 5/22/2015 4:09:33 PM
Event ID: 5973
Task Category: (5973)
Level: Error
Keywords:
User: HPENVY\Dwaine
Computer: HPEnvy
Description:
Activation of app Microsoft.SkypeTranslatorPreview_kzf8qxf38zg5c!App failed with error: The app didn't start in the required time. See the Microsoft-Windows-TWinUI/Operational log for additional information.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Immersive-Shell" Guid="{315A8872-923E-4EA2-9889-33CD4754BF64}" />
<EventID>5973</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>5973</Task>
<Opcode>0</Opcode>
<Keywords>0x2000000000000000</Keywords>
<TimeCreated SystemTime="2015-05-22T23:09:33.219596200Z" />
<EventRecordID>167617</EventRecordID>
<Correlation />
<Execution ProcessID="5600" ThreadID="26552" />
<Channel>Application</Channel>
<Computer>HPEnvy</Computer>
<Security UserID="S-1-5-21-4075998385-1554398878-[removed for privacy]-1001" />
</System>
<EventData>
<Data Name="AppId">Microsoft.SkypeTranslatorPreview_kzf8qxf38zg5c!App</Data>
<Data Name="ErrorCode">-2144927142</Data>
</EventData>
</Event>
Subject/title text switched with another of the author's sentences in order to reflect post content.

Hi,
Are you trying to remove Skype entirely, or just get rid of the tool tray icon?
IIRC, you get that icon as long as Skype is running in the background. There's a checkbox in Skype options that will keep it from running on startup. That will eliminate the icon but you won't get notified for incoming calls.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

How do i remove the exif metadata from my jpg file produced with a digital camera photo?

How do i remove the exif metadata from my jpg file produced with a digital camera photo?

The excellent and free utility Irfanview has the option to remove the EXIF data.
Simply open and the file and do a Save, or Save As with the original name.
Surprisingly, the default is to not keep the original EXIF data.

How can I package the map utility for the cannon 6d for someone to view?

How can I package the "map utility" program from the canon 6D for someone to view the shot locations and shots?

I may understand your point wrong but if you turn on GPS on the 6D, your client can view your photo location easily. Site like Flickr supports GPS (if you don't remove it) or software like Picasa, Geotag, Geosetter, Lightroom, etc.
Weekend Travelers Blog | Eastern Sierra Fall Color Guide

HT5661 how do I remove the password I just entered to protect my phone from others

how do i remove the password I just created for Find My Phone to keep people from using my phone?

The password is configured using Airport Utility in the Utilities folder. Use it to change the password. Be sure you use WPA2 security, as well.

How do I access the web utility with model cisco sf302-08p ?

Hi,i have a problem with the model Cisco SB SF302-08PP Switch , i connect a cable rj45 to my pc and configure the adapter local area connection (ip address:192.168.1.252), the LEDs blink green, and go to the address bar and get the IP by default, which according to the manual is 192.168.1.254 and the result is: page not found. Is there any way to change the web utility? How do I access the web utility?

restore the switch by holding more than 30 seconds and try accessing with ip 192.168.1.254. username and password is "cisco". before change your base ip to 192.168.1.2-253.try to ping and check the connectivity

How can we remove the following zeros from quantity field ?

Hi All.
how can we remove the following zeros from quantity field while populating ALV by using FM REUSE_ALV_GRID_DISPLAY ?
eg:getting output zqty = 2.000
but i need           zqty = 2.
help me to reslove this issue.
Regards.
jay

Hi,
While populating the field catlog do the following thing to   avoid zeros.
wa_fieldcat-tabname = 'I_OUTPUT'.    " Curr
wa_fieldcat-fieldname = 'FWAER'.
wa_fieldcat-seltext_l = text-023.
wa_fieldcat-no_zero = 'X'.
APPEND wa_fieldcat TO i_fieldcat.
CLEAR wa_fieldcat.
Thanks,
Khushbu.

How can we remove the key from the dataset which has json

uid
id
Json
4588
51
{ "key": "1/0/234", "element1":{ "a":10 "b": "test1" } }
4589
52
{ "key": "1/0/234", "element1":{ "a":10 "b": "test1" } }
4590
53
{ "key": "1/0/234", "element1":{ "a":10 "b": "test1" } }
I have the above dataset resulting from merge operation .
UID -Integer data type
ID- Integer data type
Json- String data type holding json document
How can I remove the " key" element from the json field and make my dataset look like
Expected output which will strip of key value pair from the json column
uid
id
Json
4588
51
{ "element1":{ "a":10 "b": "test1" } }
4589
52
{ "element1":{ "a":10 "b": "test1" } }
4590
53
{ "element1":{ "a":10 "b": "test1" } }
Mudassar

Hello Mudassar,
In SQL Server / T-SQL we don't have a native JSON support, so you would have to implement a solution on your own = parsing the string and remove the "Key" + it's value.
Olaf Helper
[ Blog] [ Xing] [ MVP]

How can we remove the commas from the Formula value in SAP BW BEx query

Hi All,
How can we remove the commas from the Formula value in SAP BW BEx query
We are using the formula replacing with characteristic.The characteristic value needs to be display as number with out commas.
Regards
Venkat.

Do you want to remove the commas when you run the query on Bex Web or in RSRT?
Regards

How do I remove the repetitive Utility error.

Similar Messages

Maybe you are looking for