How do I replace an ATI Radeon video card on my MacPro?

The ATI Radeon x1900 video card on my MacPro is failing. I need to replace it with a new/used model. Has anyone ever done this and if so, can you recommend a reliable source for a replacement card, AND, do you know where I can find instructions on how to replace the card? Thank you.

Happy to hear that. Good luck!
Please note the items listed under Legend in the right sidebar of this page.

Similar Messages

  • K7TPRO & ATI Radeon Video Cards

    Hi everybody and thanks for your very useful suggestions!
    I have the following hw configuration:
     - K7T PRO (MSI 6330) MoBo
     - 700 Mhz AMD Athlon Thunderbird processor
     - S3 Savage4 AGP Video card with 32 Mb RAM
     - 256 Mb PC133 RAM
    I'd like to buy an ATI Radeon 9200 (or ATI Radeon 9600) AGP 8x video card with 128 Mb RAM. Now, I know that my MoBo can support only 4x AGP video cards, but I read somewhere that, in any case, it works properly.
    Is it right?
    I looked for this question in the forum but nothing found.
    Thanks a lot
    Bye
    Willy

    Thanks Grayone.
    Well I still don't know which card to buy, basically because I was not so sure if there is hardware compatibility between video-card and MoBo.
    I will keep in mind your driver suggestions.
    Did you hear about someone that have already installed one of the two cards (ATI Radeon 9200 or ATI Radeon 9600) on a K7T-PRO MSI-6330 Mother board?
    Bye
    Willy

  • How to install drivers for ati radeon 3200?and how to config xorg.co ?

    how to install drivers for ati radeon 3200?and how to config xorg.conf?

    mawch wrote:how to install drivers for ati radeon 3200?and how to config xorg.conf?
    Hello
    I am using ati hd 3200 which is integrated with my motherboard. If you are using arch you can download & install through pacman. The package is named like catalyst*. You can install them by issuing as root user
    #pacman -Sy
    #pacman -S -l | grep -i catalyst
    #pacman -S catalyst catalyst-utils
    After installation reboot your machine in runlevel 1. (single mode).  Ensure "fglrx" module is loaded correctly using
    #lsmod | grep -i fglrx
    If the resultant output have "fglrx" part  the module is loaded correctly. The next step is to create a working /etc/X11/xorg.conf. Backup your current xorg.conf if needed.
    #cp /etc/X11/xorg.conf /etc/X11/xorg.conf.bkup
    Then issue
    #aticonfig --initial --input=/etc/X11/xorg.conf
    This will create a new xorg.conf file. Now we can test our confign.
    #telinit 3
    I am using runlevel 3 to avoid graphic messup!!
    issue
    #gdm
    If you graphical login screen works correctly there is nothing to do more except adjust your monitor resoloution as you like.
    To know your ati driver is working correctly issue as root
    #fgl_glxgears
    If gears are rolling happily it seems correct. You can also know more about installed ati driver
    #fglrxinfo
    Now the installed driver version is in the output 
    If there is any problem try following
    ##### Soloutions to solve various display problems using ATI Catalyst Drivers in Linux #####
    yes video playback is choppy until i ran :-
    sudo aticonfig --overlay-type=Xv
    Try adding the following to the 'Device' section in /etc/X11/xorg.conf
    Option "TexturedVideo" "true"
    ### This is a half solution for mythtv problems. Run mythtv in window (no full screen) If You have a screen resolution of 1024x768 try the command;
    mythfrontend --geometry 800x600
    Append the "Device" Section of /etc/X11/xorg.conf file as follows;
    Section "Device"
    Identifier "Videocard0"
    Driver "fglrx"
    Option "OpenGLOverlay" "off"
    Option "VideoOverlay" "on"
    Option "TexturedVideo" "on"
    Option "TexturedVideoSync" "on"
    Option "Capabilities" "0x00000800"
    BusID "PCI:1:0:0"
    EndSection
    Add following in the .bashrc of each user or /etc/bashrc file* Most Effective In My Case!!
    export LIBGL_ALWAYS_INDIRECT=true
    ####### Arch Linux - Add the "nopat" option to the /boot/grub/menu.lst or /boot/grub/grub.conf
    ####### as in the following example
    title  Archlinux Ice Kernel
    root   (hd0,1)
    kernel /boot/vmlinuz26-ice root=/dev/sda2 ro resume=/dev/sda3 quiet splash nopat
    initrd /boot/kernel26-ice.img
    NB: REGULAR DISCLAIMER IS ALSO APPLICABLE TO THE ABOVE MATTER; USE IT AT YOUR OWN RISK !!!  ALL THE ABOVE INFORMATION IS COLLECTED FROM VARIOUS POSTINGS IN THE FORUM AND FROM MY OWN EXPERIENCE
    Wish U good luck
    mvdvarrier

  • What would you replace an ATI Radeon 9800 Pro (256MB) with?

    Hi,
    I started a thread before asking whether I could replace a 256MB card with a 128MB card, even though the interface was a different shape.
    But, as I know so little about Macs and graphics card, it seems wiser to ask
    What would you replace an ATI Radeon 9800 Pro (256MB) with?
    The computer is user for photo editing and normal internet/email use.  The photo editing is done on Adobe Photoshop for professional treatment of photographs.
    The computer is a Power Mac G5 (1.6GHz) and budge is £80 / $120.
    Thanks in advance, Franc.

    Hi-
    Please check my recommendations in your other thread.
    Better options for the 9800 Pro are the Radeon 9800 XT, Geforce 6800 GT, Geforce 6800 Ultra, or if one has the money or finds a good deal, a Radeon X800 XT.
    For your budget and uses, the Geforce cards are a performance value buy.
    BTW, I have owned all of the cards, used all of the cards, and tested all of the cards.
    Graphics Cards- ATI and Nvidia
    See my testing pages starting here:
    Page 1: Open GL

  • How to get the Windows Vista Driver for ATI Radeon 7500 card?

    How to get the Windows Vista Driver for ATI Radeon 7500 card?
    I am using a IBM Thinkpad T42 with a 32Mb ATI Radeon 7500 graphic card AGP.
    Is there any Vista 32-bit driver to update my card so that this system support Aero effect?
    Thank you.
    regards,
    W. Thong

    wthong wrote:
    How to get the Windows Vista Driver for ATI Radeon 7500 card?
    The Radeon 9000 driver works for the Radeon 7500 card.  I have successfully used it on a T43 with Vista Ultimate x86
    wthong wrote:
    Is there any Vista 32-bit driver to update my card so that this system support Aero effect?
    Unfortunately no.  The Radeon 9000 driver should bring your graphics score up to close to 2, but it will not get it high enough to enable Aero support.
    Cheers,
    Bill
    I don't work for Lenovo

  • PE 13 crashes due to incompatible video driver detected. Running on Win 7 SP1 with ATI 540v video card/driver.  Deleting bad driver file in adobe program data does not fix the problem,  it simply replaces the text file and crashes again.  My video driver

    PE 13 crashes due to incompatible video driver detected. Running on Win 7 SP1 with ATI 540v video card/driver.  Deleting bad driver file in adobe program data does not fix the problem,  it simply replaces the text file and crashes again.  My video driver is just fine.  Any help out there?

    rb
    Your video card driver may be fine for something, but just not compatible with Premiere Elements 13/13.1.
    For those with the display card error, the answers include
    a. assure your video card/graphics card driver version is up to date according to the web site of the manufacturer of the card -
    if necessary consider a driver roll back.
    b. determine in Device Manager/Display Adapters if the computer is using 2 cards instead of 1
    c. delete the BadDrivers.txt file
    the rationale for that deletion is found in post 10 of the following older post...principle applies to 13 as well as 9.
    Re: Premiere Elements 9 Tryout Serious Display Problem
    Have you looked for computer ATI card settings that might be more compatible with Premiere Elements 13/13.1?
    When is the program crashing - just opening a new project or rather crashing if editing a particular video format at the Timeline level?
    ATR

  • Replacing Intel hd Graphics card with ATI Radeon Graphics card

    Hi, I am using an hp G62 b51SI notebook with an intel hd graphics card. However, am thinking of changing it or supplementing it with an ATI Radeon Graphics card for increased gamiing performance. Is it possible to do so?
    This question was solved.
    View Solution.

    Hi:
    Below is the link to the service manual for your notebook.
    http://h10032.www1.hp.com/ctg/Manual/c02542102.pdf
    The supported motherboards with HP part numbers can be found in chapter 3.

  • Win7 will not recognize my ATI 5870 video card in Bootcamp

    HI,
    I have a MAC pro 1.1 and I have an ATI 5870 video card.  On OS 10.9.3 the mac sees the video card just fine, but when I use Bootcamp and run Win7 I can’t get the card to work properly.  I tried to go to ATI and download the drivers but I keep "no such card found on your device" error from ATI or I can’t fine the correct drivers.  When I run Dxdiag the video area shows me no video card information aside from this card is working properly.  Can anyone assist me please?
    Thank s in advance.

    have you tried to download the correct bootcamp driver zip for your mac and manually install the latests Radeon amd driver from that?
    Apple - Support - Downloads

  • HP Notebooks HP Notebooks amd display adapter and ati radeon graphics cards stopped working

    I have a 2000-21DX9 Notebook and keep getting messages solve issues with AMD display adapte and ati radeon graphics cards they stopped working.  When I open the action center to solve the issue It says "Computer unable to download the solution at this time.  Why won't it work and how do I fix it? 

    @pp62 
    ‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
    If you are unfamiliar with the Forum's private messaging please click here to learn more.
    Thank you,
    Omar
    I Work for HP

  • How to add a nvidia ge force video card for a pavilion g6 which has a intel hd 3000?

    How to add nvidia ge force 525 video card for this laptop?

    Hi,
    The answer is no way you can add a video card on your laptop. Actually nearly all laptops including many which have dedicated video cards.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Win7 will not recognize my ATI 5870 video card on Bootcamp

    HI,
    I have a MAC pro 1.1 and I have an ATI 5870 video card.  On OS 10.9.3 the mac sees the video card just fine, but when I use Bootcamp and run Win7 I can’t get the card to work properly.  I tried to go to ATI and download the drivers but I keep "no such card found on your device" error from ATI or I can’t fine the correct drivers.  When I run Dxdiag the video area shows me no video card information aside from this card is working properly.  Can anyone assist me please?
    Thank s in advance.

    A Mac Pro 1,1 technically can't run Mac OS X 10.9 without a hack.  Thus it is unlikely the Boot Camp drivers Apple included for it would recognize anything on it newer than is supported.  You could try using another Virtualization engine that speaks to all graphics chips with their own drivers:
    https://discussions.apple.com/docs/DOC-2741

  • Replacement Program - ATI Radeon HD 2600 XT video issue

    Mac Pro (Early 2008):
    ATI Radeon HD 2600 XT video card with distorted video or no video
    Last Modified: March 15, 2011
    Article: TS3630
    http://support.apple.com/kb/TS3630
    Symptoms
    Apple has determined that certain ATI Radeon HD 2600 XT cards sold for use in Mac Pro computers between approximately January 2008 and May 2010 may experience distorted video or no video.
    Products Affected
    Mac Pro (Early 2008)
    Resolution
    If your Mac Pro experiences distorted video or no video issues and has an ATI Radeon HD 2600 XT card in it, you will need to bring your computer's serial number and the graphics card into an Apple Authorized Service Provider or an Apple Retail Store location for verification and to exchange the affected graphics card for a replacement.

    The replacement process as stated here
    http://support.apple.com/kb/TS3630
    is not correct.
    Here is my first hand experience:
    Have had the intermittent problems as described almost since the computer was new. After many calls to applecare and ROM upgrades, software upgrades and reinstalls, new boot drive - problem persisted until last week -now monitor stays on black screen on startup.
    Called local Apple store as described in support page - they know nothing about it and you cannot talk to a tech on the phone - have to make appt. Asked the receptionist to please describe problem to tech and see if they might be able to help before I take the time to make appt. I was told that they don't handle that here - go to an outside service center. Of course its Friday and the outside service is closed until Monday. Call another apple store and make an appointment - they seam more willing to help.
    Follow the instructions and remove board and take it with Mac serial number to store.
    I am told that they will not release the replacement board unless they install it themselves in my computer. I politely point out that the service doc states otherwise - no dice. Tech orders the board - won't know until Monday what delivery schedule is - he guesses 2-3 days and they can install when it comes in.
    Lesson learned.
    You can't trust what apple says in a tech document - maybe you can't believe anything they say. Frustrating part is that you can't talk to anyone to get a straight answer until you nail someone down in person - and how do I know that the tech told me the right thing. After all, doesn't corporate dictate policy? I got the policy from the corp site. So which is right?
    Do you think they would reimburse me if I went out and purchased a new board and did the replacement myself?
    "If you believe you have paid for repair or replacement because of this issue, contact Apple regarding a refund."
    I highly doubt it based on what the tech said - but who should I believe?

  • Can I replace an ATI RADEON 9800 PRO-(256MB)-MAC EDITION with Mac ATI Radeon 9800 Pro 128mb Video Card For G4/G5

    Hi,
    I am trying to help a friend whose graphics card has bust.
    The old one was an ATI RADEON 9800 PRO-(256MB)-MAC EDITION.
    I've been looking on ebay and it seems a lot cheaper to get a Mac ATI Radeon 9800 Pro 128mb Video Card For G4/G5.
    Can I just swap them over?  The connectors are not identical according to the photographs.
    Thanks.

    I'd like to thank everyone for all the really useful information in this thread. It helped me solve a similar problem, which I'll describe here briefly in case it helps someone else.
    I have a 2004/5 dual 2 Ghz PowerPC G5 and an Apple Cinema HD display linked, as I later found out, with the now defunct ADC connector. The display suddenly started to look like that scene in The Matrix, when code falls like rain down the screen, and I worked out I needed to replace my Radeon 9800 pro video card (I discovered the board was blue when I removed a thick layer of dust).
    I took japamac's excellent advice and bought a Geforce 6800 Ultra from the linked eBay seller in Hong Kong, who delivered it extremely quickly, along with the cables to plug it into the DVD drive power source and a CD with installation instructions. It was only then that I realised the card had two DVI connectors and my display needed ADC (I hadn't understood the difference).
    eBay came to the rescue again with a seller who had a secondhand DVI to ADC adapter, which Apple produced  when it phased out ADC about six years ago but no longer sells. It has its own power supply and looks like a large version of the Mac laptop power cables - and has added signifcantly to the pile of spaghetti under my desk.
    Installing the Geforce 6800 Ultra is fiddly, and a bit scary if you're not used to delving into the insides of a Mac, but the instructions were clear and illustrated with useful photos. The video cable has four connectors. Two fit into the end of the card, the other two (linked in a Y shape) form a bridge between the DVD/superdrive and its power cable. You have to remove the DVD drive, unplug it, and then plug one of the two Y video card connectors into the DVD power cable and the other into the DVD drive itself. Then you replace the DVD drive, plug the two remaining cable connectors to the video card and ease it into the old card's AGP slot.
    Finally, with the G5 reassembled, plug the adapter's DVI connection into the back of the card, plug the Cinema Display ADC cable into the adapter block, plug the adapter's USB cable into the G5 (this enables the the USB ports on the back of the display to work), and power up.
    At the time of writing, the display has been up and running for a couple of hours and all seems fine.
    Thanks again everyone for all your help and advice. If it wasn't for communities like this, it would be virtually impossible to solve problems with old but still serviceable Macs.

  • How Do I use an Ati Radeon 4870 HD for 3 Monitors

    I am new to the Apple world and community.  I recently got a new job that requires me to use a Mac Pro.  OS X version 10.6.8.  2.66 ghz dual xeon and 32 GB of ram.  It has a ATI Radeon 4870 HD.  I can run 2 monitors fine using the DVI and Mini DV port ( Using a convertor from apple. ).  When I try to use the 2 other HDMI ports for my third monitor, Mac OS wont detect it.  The wierd thing is some of the images from certain apps show on the 3rd Monitor. 
    Under graphics information it shows the Radeon 4870.  Under PCIe information it shows the same card.  On the back of my machine I have 2 HDMI slots and another lower down with Mini DV and DVI.
    The Displays I am running are 3 HP LP2475w Monitors.  Running in DVI mode with one converted to Mini DV.  The 3rd non working is running in DVI to HDMI but it can be run Straight HDMI if need.  Ive tried alot of configuration settings and I can't get the HDMI port to be detected by MAC OS.  Ive plugged one in at a time and just the HDMI do not detect.
    Please let me know what information is needed to help troubleshoot this better.

    A 5770 is $249 or slightly less and in the same dept to me as replacing hard drives, adding some RAM in order to work and because my understanding is it was the first card to support 3 monitors.
    The 5770 only requires 10.6.5+ - and the 4,1 had way too many issues with 10.5.7/10.5.8
    The 4870 may or may not provide what you need for the software you run, even though 3 yr old machine but 4 yr old plus video card.
    flashing:
    http://boeglin.org/blog/index.php?entry=entry090918-031702
    4870 vs GTX 285 that came out at that time also
    http://www.geek.com/articles/games/macpro-whats-better-ati-radeon-4870-or-nvidia -gtx-285-20090720/
    The default card was Nvidia GT120 and req'd no power cables and popular way to support more displays.
    People were running DUAL 4870s to support 3rd monitor though back then:
    http://forums.macrumors.com/showthread.php?t=665034&page=10

  • How to tell if an ATI Radeon Pro Graphics card needs any updates?

    I have upgraded the firmware on my G4 Gigabit and re-installed the combo update for OS 10.4.11, and am on an update rampage. I am wondering if I need to update driver/firmware for the video card in this computer. It is a ATI Radeon 9000 Pro. System Profiler lists its ROM Revision as 113-99703-127.
    How to tell if this needs an updated driver? Also, the ATI site lists both a download for ATI Displays Panel, and Retail Update. If I need to update, which is it, or both?
    I know nothing about graphics cards.
    Thanks!
    BC

    Hi-
    The ATI Displays panel is a handy tool. Install if you like, with no worry as to adverse effects.
    Other than that, Tiger has all the drivers that you need. No firmware update is needed, either.
    Should be no need for outside updates for the 9000.

Maybe you are looking for