How do I reset Airport extreme via that wee pinhole

I once reset my Airport Extreme via the pinhle on the back (Courtesy of Bob Timmons instructions). I cannot remember the details of how to do it. Any help?

Welcome back!
I assume that you want to wipe out the current settings and get back to a "start over" condition, correct?
With the AirPort Extreme powered on, hold in the reset button on the back of the device for 10-12 seconds and then release.
The AirPort Extreme will restart as solid amber, then after 20-25 seconds it will slowly blink amber. That is your signal that the device has been reset.

Similar Messages

How do I reset Airport Extreme Model A1034?

How do I reset Airport Extreme Model A1034?
I am using a MacBook Pro to set up the airport, but, I get this message:
"This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information."

You would download and install AirPort Utility on the PC.
For Windows 7 and above.....use AirPort Utility 5.6.1 for Windows - Support - Apple
For XP SP3 and Vista SP2......use AirPort Utility 5.5.3 for Windows - Support - Apple
For XP SP2 and Vista SP1......use AirPort Utility 5.4.2 for Windows - Support - Apple

How do I reset airport extreme A1408 to use on different network after buying new Extreme?

I have just bought and set up new Airport ExtremeA1521 and want to take my old one and set up at son's. It is A1408. Will doing a reset do all I need to do? And then I want to hook up an Express to it to extend his network.
Thanks.

Power up the old AirPort Extreme for a minute or two, then hold in the reset button on the device for 8-10 seconds and release. Allow a full minute for the AirPort Extreme to restart back to a slow, blinking amber light status.
The network settings on the AirPort Extreme are now reset back to factory defaults, and you can now set up the AirPort Extreme to create a new network with a network name and password of your choice.
Then, the Express can be set up to extend the network. If you have a new Express, it will already be set to factory defaults, so all that is needed is that device be set up to connect to the AirPort Extreme. If the Express has been previously set up, then it will first need to be reset back to factory default settings, before it can be set up again to extend the AirPort Extreme network.

How do I setup my Airport Extreme so that I can extend the coverage of my existing AT&T wifi network?

How do I setup my Airport Extreme so that I can extend the coverage of my existing AT&T wifi network?

Start by establishing a permanent fixed Ethernet cable connection from one of the available LAN <-> ports on the ATT modem/router to the WAN "O" port on the AirPort Extreme.
Ethernet cabling can be run up to 300+ feet or 100 meters, so you should be able to locate the AirPort Extreme exactly where it will be needed to provide more wireless signal coverage.
Configure the AirPort Extreme to "create" a wireless network using exactly the same wireless network name, same wireless security setting, and same wireless network password that the ATT wireless is using.
The final step is to insure that the AirPort Extreme is configured to operate in Bridge Mode, so it will work correctly with the ATT modem/router.
If you need more specific steps, we need to know what operating system you are using on your Mac or PC. If you have a Mac and do not know which operating system it is using.....click the Apple icon in the upper left corner of the screen and then click About This Mac, and post back with the OS X version number that you see there.

How do I access external hard drive connected to AirPort Extreme via iPad

Hello,
How do I access external hard drive connected to AirPort Extreme via iPad / windows laptop.
I donot have a Mac and I use windows laptop.

For your iPad, you will need an app, like FileBrowser, to access the external drive.
For your Windows laptop, you would access the drive like any other network share. The basic format is: \\<servername>\<sharename>, where, in this case, the servername is the base station name and the sharename is the name of the external drive.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

Connecting 2 Airport Extremes via ethernet if my intent is to improve wireless signal in a different area of my home

Connect the second Airport Extreme via ethernet, all is good. However, question is; do I use the same Wireless name as main Airport Extreme or do I need to name is differently? And if differently, how do devices connect to the strongest signal?

Aribia wrote:
Connect the second Airport Extreme via ethernet, all is good. However, question is; do I use the same Wireless name as main Airport Extreme
Yes. If you want your wireless devices to "see" only one wireless network, specify the exact same wireless network name, security and password for the second Extreme.
And if differently, how do devices connect to the strongest signal?
If you choose to specify different names, and your Network Preferences are configured to not "ask to join new networks" your Mac will automatically switch from one to the other, but it does not do this just because one becomes stronger than the other as you move your MacBook Pro away from one and toward the other. It will switch networks when the wireless signal falls below a threshold that is not user-selectable. It will do that whether or not you specify different wireless network names.

How to set up airport extreme with TPG ADSL2 ?

How to set up airport extreme with TPG ADSL2 ?

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How do you use Airport extreme at hotels etc, when traveling? I can plug my computer into the Airport with my ethernet but how does Airport pickup signal?

How do you use Airport extreme at hotels etc, when traveling? I can plug my computer into the Airport with my ethernet but how does Airport pickup signal? What equipment & devices do I need to travel with to make this possible?

You may mean the AirPort Express.....not AirPort Extreme.....as the Express is a popular travel router.
The whole idea behind using this device is that the hotel must provide an Ethernet jack in the hotel room. Then you connect the AirPort Express to the Ethernet jack with an Ethernet cable and configure it to provide your own wireless network in the room. You still have to agree to terms, pay the fees, etc.
The problem with this approach is that it is getting very difficult to find hotels in North America that prrovide an Ethernet jack....most have moved to wireless networks and the others are not far behind.
So, if the hotel is already providing a wireless signal, the AirPort Express is of no use in that situation.
If you normally stay at the same hotels, and know that they provide Ethernet ports, an AirPort Express might make sense in terms of convenience.

How do I use Airport Extreme to limit internet time for my kids? His computer is hardwired to the modem.

How do I use Airport Extreme to limit internet time for my kids? His computer is hardwired to the modem.

You can set up daily time limits for each computer that connects using wireless, but it is not possible to do this when a computer is connecting directly using a wired Ethernet connection.
Open Macintosh HD > Applications > Utilities > AirPort Utility on your Mac and click Manual Setup
Click the Access Control tab below the icons
Select Timed Access
For more details on this, click the Help menu at the top of the screen and enter the following phrase into the search box:
Controlling access to your wireless network
A more sophisticated approach would be to use a service provided by OpenDNS. From your computer, this would allow you to monitor web sites visited, and block any unsuitable sites. More info is here:
http://www.opendns.com/landings/familyshield

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

How do i install airport extreme on a windows pc and route it to another windows desktop?

How do I install airport extreme into a windows desktop pc and then successfully route it to another windows desktop?

The AirPort Extreme Base Station (AEBS) is an Internet router that supports both wired and wireless network clients. You can connect both of your desktop, using either media, to the AEBS for network connectivity.

How to setup the Airport Extreme for PSP?

Can anyone tell me how to setup the Airport Extreme for PSP? I have been searching the Discussions but none of the posting seems to explain detail enough. A step by step guide would be very appreciated. Thanks.
PowerBook G4 Mac OS X (10.4.3)

Sorry, I forgot to mention a few points:
1) I don't have the Airport Extreme base station;
2) My PowerBook is connect to the internet thru wired connection with the Built-in Ethernet;
3) The Airport is turned on, but my PSP's scan cannot locate the PowerBook at all (while it find someone else's network)
So, I wonder if I can just connect my PSP to the built-in Airport in the PowerBook directly. So that I can have internet access on my PSP.

How to setup the airport extreme for window xp

How to setup the airport extreme for window xp

Sorry, I forgot to mention a few points:
1) I don't have the Airport Extreme base station;
2) My PowerBook is connect to the internet thru wired connection with the Built-in Ethernet;
3) The Airport is turned on, but my PSP's scan cannot locate the PowerBook at all (while it find someone else's network)
So, I wonder if I can just connect my PSP to the built-in Airport in the PowerBook directly. So that I can have internet access on my PSP.

Can I extend my network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have CAT5 cable throughout my house but have a wireless network w/ 3 airport expresses

Can I extend my wireless network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have a wireless network with 3 airport expresses and 1 airport extreme functioning as the base station. I have CAT5 throughout my house.

Welcome to the discussions, mib88!
Can I extend the network a second time with another Airport Express...
The short answer would be no. If you want more details, please continue to the next paragraph.
Apple's "extend a wireless network" works just like the hub and spokes of a wheel. Your main hub is either the Time Capsule or the AirPort Extreme and the AirPort Express is at the end of a spoke. You can add more devices at the ends of other spokes, but these devices will communicate directly to the hub, not to another device at the end of a spoke.
Apple does offer an option which is is known as a "static WDS", which can consist of a "main", "relay" and "remote" device. The problem here is that this type of setup has two huge drawbacks:
1) All of your faster "n" devices will drop down to much slower "g" speeds
2) The bandwidth or speed capability on the network will drop down to only 25% of the original bandwidth with a "main", "relay" and "remote" on the network.
Don't think you want this on your network. Your best option is to connect the new AirPort Express to the "hub" using an ethernet connection. If you can't run the ethernet cable, take a look at a pair of ethernet powerline adapters to accomplish the same task by sending the ethernet signal over the AC powerline in your home.

How do I reset Airport extreme via that wee pinhole

Similar Messages

Maybe you are looking for