How do I resolve "Conflicting DHCP Range"?

Hello Dorohidea,
Do you mean that when you install crystal report in virtual studio 2010, you receive the error message about error 1310?
Please take a look at the following KB.
Support for Crystal Reports for Visual Studio
https://support.microsoft.com/kb/317789/en-us
In Visual Studio 2010, to create a Crystal Reports project or Web site or to import existing projects or Web sites that were created by using older versions of Visual Studio or Crystal Reports, you must first install a version of Crystal Reports that is
compatible with Visual Studio 2010.
For more information about how to use Crystal Reports in Visual Studio 2010, visit the following SAP Crystal Reports website:
http://www.sap.com/crystalreports/vs2010
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Similar Messages

Time Capsule shows error message "Conflicting DHCP Range."

I just set up a wireless network using a Time Capsule as the main router with an Airport Extreme bridged to it so I can have a strong signal downstairs. It all worked fine at first, but at some point the Time Capsule showed this error message on Airport Utility: "Conflicting DHCP Range."
The instructions that pop up when I click on the error message are beyond my level of understanding. They say: "This Airport base station rejected a DHCP address in the same subnet as its internal DHCP server. Try switching your Airport Base Station from using DHCP and NAT to bridge mode. If you still want to use DHCP and NAT to share a single IP address, change your DHCP range."
Could one of you tell me what I should do? Thanks.

Try switching your Airport Base Station from using DHCP and NAT to bridge mode.
I suggest that you do what AirPort Utility suggests.....
Open up AirPort Utility, click on the AirPort Express and click Edit in the smaller window that appears
Click the Network tab at the top of the window
Insure that the setting for Router Mode is set to "Off (Bridge Mode)"
Click Update to save the settings and give the AirPort Express a minute to restart

Airport Extreme - Conflicting DHCP Range - Only 1 router set up

Backstory:
I recently upgraded my router to the new Airport Extreme from an older Airport Extreme in order to take advantage of the Gigabit ports. The old router worked great, just wanted to take advantage of my 300mbps up/down speeds.
Problem:
My router is flashing orange and I get an error that pops up on my computer from the Airport Utility stating 'Conflicting DHCP Range'. Normally this problem occurs when there is more than one router/bridge on a single network. However, I have only the one router with no guest network set up. The wireless connection works fine, but an error pops up and interrupts me every few minutes and gets very annoying and the router is flashing orange, indicating a problem. We have tried turning on and off the 5GHz.
I've searched the forums front to back and have found others with this problem but only if they have more than one router set up on the same network.
We have 2 macbook pro retinas running OSX 10.8.3, an AppleTV, an HP printer, and 2 iPhone 5's that connect to the network.
What can I do to address this issue?!!??
Thank you,
Nick

When you configured the new AirPort Extreme, did you use the option to "Create a new network", or did you use the option to "Replace an existing device"?
Can you provide the make and model number of your modem?

TS1208 question: conflicting dhcp range

Hi out there
Am after a basic language easy to follow instrution to resolve the above
I have a TC as my main wifi router, with an extreme and express as part of the network. I have the above message on my TC, and I have absolutely no idea how to resolve. So, i am after someone who can explain how to fix this, and please do so as if I am the dumbest person out ther, I do not understand any of this DCHP/NAT/PPoPe stuff, all it says to me is "blah, blah blah blah!"
Ihave attached to my TC via ethernt - Mac Mini, Denon AVR, and apple TV. And wireless I have an Asus PC touch screen as a media server.
Am trying to set up so I can airplay wirelss with iphone 3gs, and 4g, plus retina ipads.
All help greatly appreciated!

No complex network is easy .. sorry but the easy is a modem wireless router and every item connected to it.. then it is easy.. as soon as you have multiple items.. it gets hard.
First question is, if you don't have the skills to do this get in a Tech.. think of it as the washing machine on the blink.. if you have that happen most people do NOT start stripping down the washing machine.. they call a tech.
Same here. Networking is something that people do a couple of years in school for a diploma level.
If you want to DIY..
The first step is to write down the IP of every single item..
So start with the Ericson modem router. What is its IP and dhcp set to?
Please list that.
Please remove everything from the network except the TC and modem.. and any switches.. they are fine.
Put the TC back into bridge modem.. and ensure it gets an IP from the Ericson.. if not restart the Ericson and the switch and the TC.. make sure it gets an IP and you can ping it.
List the IP of the TC.. make sure in the Ericson it is listed correctly.
Also note.. items have issues with Apple names.. please name all your apple devices to SMB standards.. short, no spaces and pure alphanumeric.
No luck.. wire the TC direct to the Ericson.
No switch.. nothing else but a computer wired to the TC to see what is happening.
So you have
Modem--ethernet--TC in bridge--ethernet--computer.
Note down again the IP of everything.
use the tools in the computer.. ping and traceroute to make sure you have local and internet access.
Always..
Reduce complexity of the network, until it works.. then add items. one by one.. ensure every part works as it is added. If a part doesn't work.. reset it and try again.. do the setup in isolation from the network.
Or call a tech.. and think of it as a washing machine.

How can I resolve conflict between itunes and Windows 8.1

When downloading itunes to my laptop computer, using Windows 8.1 my email/network account will not work on that computer. It is fine on other devices such as ipad and Windows phone. I can also pick up emails on online on the same laptop. There appears to be a conflict between itunes and Windows 8.1

Please see Boot Camp for comments.

10g streams and resolving conflicts

Hello
i configured oracle streams on 2 databases using the wizards in enterprise manage (10gR2) r, the aim is to set up multi master replication quickly and easily.
If i do this how do i resolve conflicts or are they resolved automatically? I read that you can call
DBMS_APPLY_ADM.SET_UPDATE_CONFLICT_HANDLER(
object_name => 'hr.locations',
method_name => 'MAXIMUM',
resolution_column => 'time',
column_list => cols);
but this is not inserted into teh scripts generated by enterprise manager. Is it there a default conflict policy? or can i
configure this globally?
Also i noticed that my servers from time to time stop reqwplication and flow gets paused with an enqueue error. Is this just a resource issue?
I am limited currently as I am trying this out with vm images.
Am willing to upgrade to 11g if functionality of streams is better.
Thanks
Edited by: user573756 on 06-Jun-2010 07:45

You are seriously confusing totally different technologies.
The name of this forum is Advanced Queueing.
Your question appears to be about Streams
Then you ask about multimaster replication which sounds like Advanced Replication.
What are you actually doing and with what technology are you doing it?
I have no experience doing this with EM, only hand coded scripts via SQL*Plus so I can not comment on what EM is doing or not doing.
But without a clear understanding of what conflicts are possible in the case of your design it is impossible to advise you further. A well
designed system should make conflicts if not impossible ... extremely rare and narrowly focused.

Trying to set up Directv GenieGO using Airport Extreme. Getting error message: DHCP range entered conflicts with the WAN IP Address of your base station. How do I resolve the conflict.

Trying to configure an Airport Extreme manually. After I enter the IP Address of the GenieGo along with the rest of information required I am getting the following error message when I click update:
DHCP range entered conflicts with the WAN IP address of your base station.
How do I resolve the conflict?

You cannot use the same range on LAN and WAN if you are routing.. it must be different.. and you should not be routing at all.
The AE should be in bridge mode. NO DHCP settings at all.

How do I change DHCP range other than standard options

Recently I discoverd that the settings of the DHCP range of my Time Capsule changed after an update. Through my provider we have received a DHCP-range so I can access the disks remote via BTMM. Due the the internal fiber network it was necessary to adjust this. The range which was set started with 37.17. After the update it is only possible to choose from 10.0, 172.16 or 192.168.
The problem now is that I cannot remotely access my TC from outside the office. Can anyone please hand me a sollution.
See screen captures below
NEW:
OLD

This is interesting one.. normally the setup when using a block of IP's is not NAT at all. NAT must use the private IP address range.
So I am not sure how it worked in the old setup.
On the Internet tab.. you should select the static IP.
Then on the network tab, you set the dhcp to the actual range of addresses that you have been given.. surely not the whole block of 200 addresses.
That is just how the Apple auto fills it in.
It is only if you NAT that you would then have issues with the private IP range.
In this case you are NOT going to NAT. You are applying an ISP provided range of IP addresses to your clients.. and you must use just dhcp..
I cannot understand how you OLD picture with dhcp and nat could have worked. But it was a mistake in an older utility.. at a guess.

Does anyone know how iCloud resolves conflicts? (iOS save games)

Hello all,
We're having some users report an issue with our App that their save game is being nuked when they close the App, sing in to iCloud and then re-open. We have a number of leads we can follow, but first thing is first; Does anyone know how conflicts are resolved by the iCloud system? What it does internally?
Scenario:
Achieve some amount of progress through an App.
Achieve some other amount of progress through an App from a different device.
Sign into iCloud on both.
iCloud obviously decides which data to use, but how? Is it literally just a "last write to file wins" case?
Another question is, does anybody know if iCloud would act strangely/not at all on a device which was jailbroken? We have a very small number of users reporting this issue so that may be another likely situation.
Many thanks

Yes, we are fully supporting iCloud. It's a very rare case that we get this report from users and no solid repro steps have yet been given. Many users have successfully played on multiple devices with iCloud enabled and their save game is perfectly intact. There just seems to be an edge case where it's possible that a call to iClouds synchronize and what it actually does in that function is resolving an older save file. So knowing what the internals of how it resolves conflicts will allow us to add another layer with our own conflict resolution specific to our App.

HT2548 How can I resolve a conflict of 2 different iWeb Domains in my Library?

I somehow (using 2 different Macs) created 2 different iWeb domains (Domain and Domain 1) and now need to combine them into one Library on my new iMac. How can I resolve this issue? I want to be able to merge Domain 1 into Domain, so I can also FTP publish the pages in Domain 1 to my new webhosting service, (in addition to the many others I've already published from Domain). But I don't know how to merge them or even if it's possible? Can anyone help me out with this? This is the last thing I need to do before moving to iCloud. Thanks.

In Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
To open your domain file in Lion or to switch between multiple domain files Cyclosaurus has provided us with the following script that you can make into an Applescript application with Script Editor. Open Script Editor, copy and paste the script below into Script Editor's window and save as an application.
do shell script "/usr/bin/defaults write com.apple.iWeb iWebDefaultsDocumentPath -boolean no"delay 1
tell application "iWeb" to activate
You can download an already compiled version with this link: iWeb Switch Domain.
Just launch the application, find and select the domain file you want to open and it will open with iWeb. It modifies the iWeb preference file each time it's launched so one can switch between domain files.
WARNING: iWeb Switch Domain will overwrite an existing Domain.sites2 file if you select to create a new domain in the same folder. So rename your domain files once they've been created to something other than the default name.
OT

Airport Extreme 802.11ac manual DHCP range

I have one of the new Airport Extreme 802.11ac units, and am running airport utility 6.3 on my server.
I am trying to setup my network but I would like my own DHCP range instead of 10.0 or 192.168 - I would like to add 10.20, This way it wont conflict with my other network for work which has 10.0 and my IP TV Network which is 192.168. I would like to add a manual address for my home netwok so I can add a vpn to avoaid the conflits.
Is there anyway of adding my own DCHP range in the new extreme?
Thanks
Greg

It isn't possible to change the first two octet values other than what apple has already allowed.. ie 10.0, 172.16 or 192.168
That is how Apple build their stuff.
I have no idea if this would work.. but someone else suggested the idea.. export the configuration of the AE .. you will find that is available via the top menu.. then open the xml file that is produced and do a search and replace for 10.0 to 10.20 or whatever you want.. save the file.. and import it back to AE.. it is crude windows sort of operation but it worked to change dhcp messages for the poster.

Shortly after launching into itunes, it freezes and I get the following message: A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available. How do I resolve this issue?

Shortly after launching itunes, the program freezes and gives me the following message:A problem has caused the program to stop working correctly. Windows will close the program and notify you if a solution is available. The program then closes, even if I have not completed what I am doing. How do I resolve this problem?

That is what I thought. Cannot figure out how to turn it off, though.
However, when I talked to her over the phone, she is definitely using Firefox. I tried to access her Internet Explorer, but it has been deactivated, I believe by Firefox.
She primarily uses the Internet to communicate with her kids, grandkids, and great grandkids. Her e-mail account is with Yahoo Mail, and she uses Firefox to access it. Occasionally, she uses the web to look up information, and may have downloaded a virus.
Do you think there's something in Yahoo Mail that conflicts with Firefox? Is there some remnant of Internet Explorer that needs to be deactivated? Could she have a virus?
Any information would be gratefully appreciated. I live 7 hours away, and can only help her over the phone. I'm trying to develop a course of action that I can use with her. I know a little bit about Firefox, so need your expertise.

How can I resolve a NAT config issues with Arris router & AE

I'm having NAT conflict issues. None of the existing threads on the forum match my configuration. I have an Arris Cable Router/Modem (Time Warner) with 4 ports. Port 1 feeds an unmanaged switch for ethernet connected devices, and port 2 on the Arris router feeds and Airport Express. Getting "Double NAT Status" on airport utility for the AE. How can I resolve this while not effecting my wired devices ? Thanks so much !

To resolve the NAT conflict you simply need to reconfigure the AirPort Express as a bridge.
You would do so using the AirPort Utility, as follows:
Run the AirPort Utility, and then, select the AirPort Express.
Select Edit.
Select the Network tab.
Change Router Mode to: Off (Bridge Mode)
Select Update and allow the Express to restart.

Conflict Resolver trying to resolve conflicts from 2004

It's irritating..... having used Entourage and iCal since 2004, now in trying to sync with 3g, I am getting this pop up that asks me to resolve conflicts dating back in 2004. Is there an option where I can ask it to ignore retroactive dates? My only option is 'resolve with < program here >'

After our power went off, I came home to find 64 "conflicts". Evidently an .mac folder was deleted, but I seem to have resolved that. However, no matter HOW many times i "resolve" the conflicts between the Mac and my Palm Treo 650, every few minutes Conflict Resolver pops up with the same 64 conflicts. Very frustrating. I wonder if there is a com.apple...... file out there somewhere to delete and start over.

The ipad"ipad" could not be restored. An unknown error occured (16). How do I resolve this error?

The ipad"ipad" could not be restored. An unknown error occured (16). How do I resolve this error?

Your error code falls within the 10-47 range mentioned here.
Check for hardware issues
Related errors: 1, 3, 10-47, 1002, 1011, 1012, 1014, 1000-1020, 1669.
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support.
Error 1015 might happen after making unauthorized modifications to iOS, also called "jailbreaking."
Use recovery mode to restore your device
Related errors: 1015, “The required resource can't be found.”
You might see these error messages if your device has a beta version of iOS or if you're installing an older version of iOS (downgrading). Use recovery mode to restore your device to the latest version of iOS.
Quit virtualization software
Quit any virtualization software (such as Parallels or VMware) that’s running on your Mac. Then use the latest version of iTunes to restore your device.

How do I resolve "Conflicting DHCP Range"?

Similar Messages

Maybe you are looking for