How do I set the power-up settings in FieldPoint for an FP-TC-120 on an FP-1000 interface?

Each time my computer reboots I find the channels on the FP-TC-120 read in what appears to be voltage (i.e. ~.0000561) even though FP Explorer shows the channels configured as -270 to 1770 Cel. I find I have to Edit each FP-TC-120 module at which point I get "The attribute, range or powerup values do not match the current file settings. Which would you like to use?" When I click the File button and then Accept the channels start reading in degrees once again.
I tried the Snapshot and Powerup state saving directives but I do not get the factory configuration checkbox nor the Snapshot button.
Attachments:
VVPTS_FldPt.iak ‏43 KB

Rick,
You need to right-click on the FP-1000 and choose Edit This Device. You will then have a checkbox in the middle right portion of the window called Factory Configuration. Un-check it. At this point, every time the FP-1000 is re-powered, it will configure all IO modules with the "User" configuration, rather than the factory default configuration. Note: You must do these steps while the FP-1000 is connected to the computer and powered on.
Regards,
Aaron

Similar Messages

How can I set the default print settings of my document as color. I want the default print setting to be color when someone opens a document. similar to duplex print preset is there a color print preset?

How can I set the default print settings of my document as color. I want the default print setting to be color when someone opens a document. similar to duplex print preset is there a color print preset?

Hi,
Try saving your settings as a Preset by clicking the Preset drop down and then select Save Current Settings as a Preset.
Next try changing the settings by selecting the saved preset.
That allow saving the settings for a specific printer, I assume it may also allow selecting these settings for another printer.

How do you set the zoom level to Inherit Zoom for all bookmarks in a pdf?

How do you set the zoom level to Inherit Zoom for all bookmarks in a pdf?

beatngu13
I made an account just to "like" your comment and say that you are a god among men.
I've been searching for hours about how to make the zoom level persistent throughout following links in various PDF's I have, and most sources were saying to just buy acrobat pro and edit the bookmarks manually with it.
I saw that it was possible to write an application to change the property, and considered doing it after the only pre-existing custom application I could find was asking for $50.
Thanks to you, I no longer have to worry about re-zooming every time I click a bookmark, and I'm not out $50 or the time it would take to code an app myself!
From the bottom of my heart, thank you!

How can I set the polarity / range of NI 6014 for 0.0V - 10V?

How can I set the polarity / range of NI 6014 for 0.0V - 10V?

Nilton,
The NI 6014 only has bipolar (10V to -10V) mode available, not unipolar (10V to 0V). Look into our E Series boards for both unipolar and bipolar operation.
Ames
Applications Engineering
National Instruments

How do I set the about:config settings for all users? iprism keeps prompting from authentication for users.

When users log on and try to open Firefox 23.0.1, users are prompted with Iprism Authentication. We made changes to the firefox about:config values "network.automatic-ntlm-auth.allow.-non-fqdn" and "Network.negotiate-auth.allow-non-fqdn" to true and it works, but only works on a per user basis. How can we set this up for all users?

I would think the about:config entries discussed are ex-factory set to values each user has to change individually, after the installation has run its course. The solution could be to have patched files ready to install post factum:
[https://developer.mozilla.org/en-US/docs/Mozilla/Preferences/A_brief_guide_to_Mozilla_preferences A Brief Guide to Mozilla Preferences - MDN]

How do I set the default page when I select "+" for a new tab? Right now it defaults to Yahoo search and I want to set it to my Speed Dial page. I did have the default page set to Speed Dial but I can't find anywhere how I did it in the past.

You can set the homepage for opening tabs, but I can't find the setting for designating what page opens when I hit the + button on tabs.
This is the page that loads:
http://search.yahoo.com/?fr=freeze&type=W3i_NA,132,3_6,Tab%20Search,20100937,6693,0,16,0
How did Yahoo embed this in the Tab settings?

Firefox '''does not''' come with a setting for a page that opens in a new Tab, the default installation always opens a blank page when you open a new Tab. Many extensions include a feature to open their choice of a webpage when you open a new tab, as does the Speed Dial extension which uses a "local page" internal to Firefox.
You need to figure out which extension has taken over that preference that Speed Dial needs to use. You didn't bother providing a Troubleshooting Information... listing as requested when you asked this question, but I can guess your problem is related wither a Yahoo extension or a Conduit / OurToolbar extension - as there is a plugin listed = Package Installer & Install Conduit.
http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes

#*$!%! Can't figure out how REALLY to set the printing defaults so they STICK for everything

PLEASE DON'T REPLY HERE. PLEASE REPLY TO MY IDENTICAL POST AT
http://h30434.www3.hp.com/psg/board/message?board.id=Software&thread.id=5348
On our 6-month old HP OfficeJet Pro 8500 Wireless A909g, we can't seem to figure out how to set the DEFAULT printing parameters so they really apply to all docs (unless we designate otherwise for a particular doc, of course). When we set them, sometimes they work for the next doc, and sometimes they revert back to an earlier setting.
There seem to be three ways to set parameters for the printer: Properties, Printing Preferences or Printing Defaults on the Advanced tab. (We really thought Printing Defaults on the Advanced tab would do it, since it's so hard to find, but ... NOT.)
My partner thinks it's an HP conspiracy to sell more ink because the reversion is to General with Color (the most ink-intensive, as far as I can figure out). We are trying to fix the machine to start always with Fast-Economical/Black Ink Only. Sometimes it's there and sometimes we have to re-jigger first. We still have to check every time.
Also, I want to fix every job to "Print Back to Front" because the printer shoots out the pages face up. Again, sometimes it's there, and sometimes we have to re-set before the job.
Also, whether we get the default we had set or we re-jigger first, the settings don't stick for every worksheet in an Excel workbook. Or sometimes not even every page.
So, who out there has the 100% foolproof guide to NAILING DOWN THOSE SETTINGS FOR EVERYTHING?
PLEASE DON'T REPLY HERE. PLEASE REPLY TO MY IDENTICAL POST AT
http://h30434.www3.hp.com/psg/board/message?board.id=Software&thread.id=5348

Locking this accidental double post and directing people to the linked original thread.
Clicking the "Kudos star" to the left is a great way to say thanks!
When your problem has been solved, accept the solution by clicking the "Accept as Solution" button to help other members in the future!
Rules of Participation

How can I set the CS5 to Intuos Pro Large for changing brush size and opacity and others?

How can I set together to my PS5 or Ps6 in order to change brush size and opacity at the Intuos Pro Large?
Nachricht geändert durch Orhan Tarman

The MTU setting on the interface is the layer 3 packet size. In this case, the MTU is set to 1500, but the largest frame size transmitted on the interface (including layer 2 headers) is 1516. It sounds like you are experiencing another problem at the LES.

How do I get the power manager settings to take hold? And stay that way?

I want to have my computer awake while on the battery and while I'm driving my car. To reduce distraction, I want to have the lid closed.
In order to make this mode easy to get to, I created a new power plan that has the "lid-closed" event result in "do nothing". Sometimes, this works. Sometimes, the computer goes to sleep. It is exceedingly annoying when the computer goes to sleep because I will get to my destination 45 minutes later and find that the computer didn't do what I wanted.
I've also noticed that the setting for "do nothing" sometimes bleeds over to other power plans. This is also a problem because, under ordinary situations, I would like my computer to behave normally.
Here's a summary of the situation:
1. I've disabled the "apply the settings to all power plans" button.
2. I've created a new power plan called "Logging" that should stay awake when the lid is closed. This power plan will sleep after 65 minutes and hibernate 10 minutes after that (on battery).
3. This plan stays awake sometimes, but not other times. At this instant, sitting in my living room, it refuses to stay awake. Oops, just tried it and now it works (a little consistency here would be nice).
4. As a case example, this morning the computer behaved as expected: I arrived at my destination and it was still away and logging. This afternoon, I woke it up and started logging, closed the lid, and drove off. Upon reaching my destination, I discovered that the computer went to sleep as soon as the lid was closed.
5. The program I'm running logs data points. When the computer sleeps, data points don't get logged. Therefore, I know the computer is sleeping because, after a long logging session (45 minutes), there will only be a few seconds of data points (which correspond to the amount of time it takes to close the lid). If the computer goes to sleep after 10 minutes or 30 minutes, there would be many more data points.
6. When the computer hibernates or sleeps, it seems to remove whatever change I last put into the plan. Even so, the plan still "says" that the change is there.
Ultimately, the difficulty here is that I can't predict what the computer is going to do. If I could, then I could adjust my use pattern.

Try this:
Go into Power Manager, choose the Logging profile.
Go into Windows' Power Options, choose a different profile, then switch back to the Logging profile.
See if this clears any contradiction between the two.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

How should I set the print control in a SmartForm for barcoding?

I already have defined the prefix(SBP27) and suffix(SBS01) print controls, now I would like to know how set them in the field in the Smart Form.

Jorge,
The forum you have posted your question in is for questions related to the SAP Business One SDK. Is your question related to the Business One SDK?
Eddy

How to set the same General settings for all users

Hi Experts,
How can i set the same general settings for all users e.g. marking the checkbox "Display header" to true for all users? General settings are possible under User Settings Button.
Regards,
Arti.

Hi Arti!
You can default user settings in a PFCG role, in the "personalization" tab.
If you have a PFCG role that is common to all your users, you can set the default values here.
However it does not prevent them to change these settings later, except if you modify the "user settings" fields properties in cProjects application.
Matthias

How Do I set the "Record" settings in Sound booth.

How Do I set the "Record" bit settings in Sound Booth, i.e. the 16 bit rate so that the wav files will burn to a music CD. (the default 48 will dot burn to a CD).
Thanks Marv.

Why not post in the SB forum?
Go to File/Record and set the format to what you need:

How do I set the cal factor in a graph properties via a GUI

How do I set the cal factor under properties in a graph window to different values using a GUI interface; button, or selector?

Sorry about that, what I meant to say was "multiplier". I need two different multipliers at different times.
Attachments:
GraphProperties.PNG ‏40 KB

HELP !!! How can I set the size of each component separately

Please tell me, when adding components (a mix of
labels , buttons etc.) on a container (swing), how can I set the size
of each component separately.
for example:
the code here has a mix of button and a grid that is actually another JPanel. Its a part of a bigger
program. When running the grid is cut (not seen in its full size).
So, please try to anser also about the specific acse of frame contining another frame in it , and the interior should be right sized.
The relevant part of the code:
=========================================
public class Reversi extends JFrame {
public static void main(String[] args) {
Reversi ourGame = new Reversi();
public Reversi() {
super("Grid Reversi");
setSize(new Dimension(300, 300));
setDefaultCloseOperation(EXIT_ON_CLOSE);
Grid g = new Grid(); // the grid was built at another part..
ReversiGame ourGame = new ReversiGame();
JButton b;
JFrame f = new JFrame("Hello Java");
f.setSize(new Dimension(300, 300));
f.setDefaultCloseOperation(EXIT_ON_CLOSE);
Container c = f.getContentPane();
c.add(g,BorderLayout.NORTH );
c.add(b = new JButton("Hola"), BorderLayout.CENTER);
//f.pack();
f.show();

BorderLayout chooses the sizes of each of the components added to it. Choose a different layout manager (or set the placement/size manually with a 'null' layout)
http://java.sun.com/developer/onlineTraining/GUI/AWTLayoutMgr/shortcourse.html

How could I set the proxy settings for just some URLs and not for all?

Hello,
I am using HttpURLConnection to establish a HTTP connection . The connection pass through a proxy, and it requires security.
I know that I can set the proxy settings in the system properties, and this works perfect.
But I don't want to set the proxy settings in the system properties, because this proxy settings will be for ALL the URLs, and I just want for a few URLs.
How could I set the proxy settings for just some URLs and not for all?
Thanks

java.net.URL.openConnection(java.net.Proxy proxy)
@since 1.5

How do I set the power-up settings in FieldPoint for an FP-TC-120 on an FP-1000 interface?

Similar Messages

Maybe you are looking for