How do I set up a Netgear WNR3500 as wireless extender with the Airport Extreme as my main router?

I just got the Airport Extreme yesterday because the Netgear couldn't hold all the computers we had on it. Now the Apple router works great, except for it is downstairs in the basement because our home computer is ancient and only connects via ethernet cord. So the Wi-Fi upstairs is only one bar on my smart phone way in the corner far from the router. I did some research and found out that the Netgear WNR3500 can be used as a wireless extender. I want to hook it up on the main floor away from the Airport where the signal is strong so it will still get great connection but will be able to transmit that same great connection a little bit farther. I just want to know how to do that.
Thank You!

The Netgear WNR3500 has mixed reviews at best and their customer support is unformly regarded as poor.
Interesting how different people have different experiences - although I never needed their tech support, so I would not have an opinion on that, this wireless router was the absolute best router I've ever had. I had to stop using it because I changed ISP's and was forced to use their modem/router combination (nothing else will work with their new V-DSL service); however, I've kept the router in case I should need to use it as an extender (which I haven't). In any case, unlike D-Link, Belkin, or Link-Sys which would at most give me one bar in my livingroom and the signal would cut out intermittently (livingroom is 50 ft from study), the Netgear showed all the bars and was steady as a rock. Configuring it with MAC filtering on their website was much easier than my current one as well.

Similar Messages

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network with newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

My Power Book G3 Pismo with an Airport wireless card running Mac OS X 10.4.11 will not connect to my new Airport
Extreme Base Station using WPA Personal/WPA 2 Person encryption. The Airport firmware is version 9.52. From
posts I've read online at different places indicates the Airport card should support the WPA encryption. Perhaps the problem
is the Base Station is using a combination setting and the fault is in the base station?
Thanks for any suggestions

Perhaps an inexpensive usb wireless adapter would work as well?
This is probably the simplest way to get the G3 connected to the wireless network.
I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
The new AirPort Extreme is broadcasting a wireless signal.
A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable.
This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
I do have an old Linksys Wireless G router. I wonder if that would work?
In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

How can I extend a wireless network with my AirPort Extreme Base Station?

Today I purchased a brand new, dual-band base station to replace my Belkin N router, as I have had a handful of firewall, coverage, and other networking problems in my house lately. First off, I really like this router and it was very easy to setup. My MacBook Pro could use both bands and established a 300 Mbit/s link very quickly. After tweaking various settings to my liking, I was also able to maximize the connections on many of my non-Apple machines and devices. I noticed that the range of its network was better than my Belkin's, but unfortunately, it failed to completely saturate the area sufficiently. Since the Belkin still works well enough, I was hoping I could bridge them together one way or the other.
The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct? I would like to place them at opposite ends of my home so I can get strong WiFi signals everywhere inside. However, when I try to get the base station to connect to my preexisting WiFi connection, it tells me that I can't extend the network and fails to join.
So is this possible? And if it is, how would I go about setting it up? I know it would probably be easier if I had a simple range booster such as an AirPort Express, but I didn't buy one while I was at Fry's since I hoped I could make use of the older Belkin. This is its product page, if needed. Thanks for any suggestions.
-MacUser

The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct?
Sorry, but no. The AirPort Extreme Base Station cannot "join" a network like the AirPort Express or Time Capsule, but you wouldn't want to do this anyway because in this configuration these devices will only perform as wireless clients ... not routers.
Instead, the AirPort Extreme can either be extended or can extend another 802.11g or 802.11n AirPort ... or a very very few non-AirPort devices.
One option for your Belkin would be to connect it to the AirPort Extreme by Ethernet but this may not meet your requirements or be a desirable situation. Otherwise, you would need to get another AirPort to extend your current one.

Setting Up Comcast to Work with the AirPort Extreme Base Station

I just set up Comcast high-speed internet through the cable modem and ethernet connection and it works fine. What I need is a step by step instruction on how to set up the connection through my AEBS. I've tried to configure using the Admin Utility, the AirPort Set-Up Assistant, the Network panel---all with no success. I'm not sure what to enter in the boxes or what to check. I've read the "Designing AirPort Networks" PDF and it wasn't much help.
The AirPort Network was working fine with the dial-up connection I had before.

Voila! NOT!!!
I'm having the same problem trying to set up a friend's "new" Macs, and I cannot get them connected to the internet. I've also followed the same steps. I tried the resetting trick (unpluging, waiting, repluging the modem first, then the Airport Extreme Base Station.)
The DSL ISP is SBCGlobal. Their dsl modem is SpeedStream 5100. The AirportEBS is the about 4 year old white base station with the phone jack, and a WAN and a LAN ethernet ports. I'm trying to connect two iBooks and a MacMini.
Everything did fine for the past year with the modem in "regular" mode and only ONE Mac connected. When the new Macs were recently acquired, SBC techs said that the modem needed to be put into PPPoE mode so that multiple Macs could be connected at the same time. This was done. [The techs said in regular moden the modem does the authentication; in PPPoE mode the modem acts as a bridge and the AirportEBS is the router and provides the authentication. I am assuming the techs are coreect, but I don't know for sure.] The CAT5 ethernet cable from the modem goes into the WAN port on the AEBS. The computers all see the local wireless network set up by the AEBS.
However, when any of the Macs try to connect to the internet, the error message returns "No PPPoE server available." Resetting the modem and base station has not cured this. [n.b. Bypassing the AEBS completely by connecting the CAT5 cable from the modem directly to the Mac will provide internet connection.] Any other ideas? Sounds like both of us are having the same sort of problem.

How can I open the ports with the Airport Extreme?

I have an Airport Extreme Base Station connected to a cable modem and I want to open the ports for the two Playstation 3's I connected to the Airport Extreme via Cat 6 ethernet cable. The first Playstation 3 will be used to play Call of Duty Modern Warfare 2 and the other Playstation 3 will be used to watch streaming movie from Netflix. Does anyone know if this can be done?

It is documented on Page 54 of Apple's "Designing
AirPort Networks Using AirPort Utility Mac OS X v10.5 + Windows" (direct PDF download link).
The public port and private port would be set the same value.

How do I set a landscape mode for my print out with the CNIreport?

I am using CNIReport and I was wondering how to set a landscape mode when printting?

There is a property of the CNiReport object called "Orientation". You just set that property to Landscape using the enumeration provided in the CNiReport class. Here is an example with the full path to the enumeration value:
m_report.SetOrientation(NI::CNiReport::NiReportsPageOrientation::NiReportsLandscape); //m_report is the CNiReport object
Best Regards,
Chris Matthews
National Instruments

How do you set up a MacBook Pro and a PC with one Airport Express?

I have a MacBook and my roommate has a PC and we're trying to set up my new Airport Express at our college so we can hook up our computers and printers to it. I had it so that my laptop worked fine, but hers would "connect" and not really have any internet connection at all. Class starts on Thursday, so help would be kindly appreciated!

I'm a great believer in the KISS principle.
Configuration is simple if you start from a factory default condition. Connect the Airport to AC power and finally to the Internet modem (or modem/router). Open Airport Utility on your Mac or other computer and accept all of the recommendations. After confirming that it works, insert your desired administrative and WiFi passwords.
Do not expect the Airport to respond instantly to the configuration commands. BE PATIENT!

Setting up wireless network with 2x airport extreme ac

I've got a business customer with 2 new Airport Extreme 802.11 AC behind a comcast modem.
When the first extreme is set up, all is well.
When the 2nd Extreme is introduced, Airport Utility asks to automatically wirelessly extend the network, which I allow it to do.
But sometime during that setup, the 2nd extreme becomes unresponsive, and the connection to the internet becomes broken.
The only thing that restores it is to reboot the first Extreme. No matter how many times Iv'e done this, it results in the same problem. I've replaced Extreme #2 with a new one, and I get the same problem.
There are 20 some odd devices on the network; with one Extreme, it works great, and the Extreme AC's replaced 2 older version of Extreme's that were doing this just perfectly.
What is causing this problem, other than me doing something stupid, and how do I extend the network? I'd rather extend it with the wire it's connected to than wirelessly.

Power off AirPort Extreme 2 for now and test the Ethernet cable that is connected from one of the LAN <-> ports on Extreme 1 by temporarily connecting the cable to the Ethernet port on a laptop or desktop. Turn off the wireless off on the computer and see if you can get a good Internet connection that way.
If you can, then you know that the Ethernet port on the AirPort and the cable are both working correctly.
If you can't, then you need to do some troubleshooting to identify the real problem before you can attempt to configure AirPort Extreme 2.
Post back when you have verified that you have a working connection between AirPort Extreme 1 and the device that you are using to test.

HT204053 how do i set up mail on more than 1 iphone with the same apple id

i have a iphone 4 and an iphone 5 both using the same apple id but the iphone 4wont let me use the icloud or set up any mail accounts on it any one know how to change this . icloud is down lighted and wont do any thing and when i try to set up mail it is also down lighted

"down lighted"? Do you mean grayed out? If so, the go to Settings and check to be sure restrictions are not turned on. They need to be off.

How to set-up new Airport Express to extend range of Airport Extreme

Purchased a new Airport Express to use it as a range extender on existing home network with an operating Airport Extreme base station. While I've read instructions, I'm unclear whether the Express needs to be connected by ethernet cable for its initial setup, or can I simply plug it and initialize it wirelessly onto the same household network? (I've tried the latter but without success).

to edex67 and Bob Timmons:
My objective is to extend the wireless range of the Airport Extreme base station wirelessly - so I do appreciate that the Airport Express would needsto be located haflway between the base station and the "dead zone" area.
The suggestion of using a Powerline ethernet connection to the Airport Express has merit (especially as I have one available).
I continue to use OSX 10.6.8 - does this affect my set-up in any way?
My problem had been - and remains - how to configure the Airport Express in range extend mode - I did click these boxes on both the Extreme base station and the Express, however the Express still has flashing amber lights and error codes - one indicating no internet availability on the Airport Express.

Help setting up Open DNS with new airport extreme

I cant seem to get Open DNS to work with a new airport extreme. The status says I am not using Open DNS and its not filtering anything. I have followed the exact steps for set up listed on their website, checked the dns settings, cleared both caches and restarted the computer, modem and router with no success. I set the airport up in bridged mode, although I tried the other option under setup, but not sure what I was doing? I picked up this router because I wanted easy set up and the apple store assured me it would work with Open DNS. Oh, and I also downloaded the latest firmware update on the router. Can anyone help me with the settings or what else I need to check?

Sorry, I am not familiar with this product, so I checked online to pick up some information. Here I am referring to the information found here:
http://www.dslreports.com/faq/6096
I found that your device is mentioned as follows in the intro under Section 1 of this document:
The BellSouth supplied Westell 2100, 2200 and 6100 models (Models A90-210030-04, B90-220030-04, and B90-610030-06/C90-610030-06, respectively) share many features and functions.
Next, I am referring to the information under Section 2, under the heading of Standard Default Mode Connection (separate hub or switch present). Unless you have changed the configuration on the Westell, this is how your device is operating. In this mode, the Westell device is acting both as a modem and router in one unit.
So, an attached router (AirPort Extreme) must be configured as a switch to work correctly. That is what Bridge Mode is....the AirPort Extreme is operating as a switch when it is in Bridge Mode (which would be the correct setting to use when the Westell is set to its Standard Default Mode).
Any changes that you want to make regarding DNS settings would need to be made on the Westell device, since it is acting as the main router on your network.
In Bridge Mode, the AirPort Extreme simply passes that information through to its connected devices. You will not be able to make any DNS related changes on the AirPort Extreme since it receives that info from the Westel device. Some service providers force you to use their DNS servers, so you might want to check with Bell South or AT&T for more information in this regard.
If you want to be able to configure the AirPort Extreme as the main router on your network, and instruct it to use the DNS information that you want, you will need to refer to the section under the heading of Bridged Ethernet Mode ( separate router present).
Please note that the first item under this heading specifies that "This is the preferred configuration when using a separate external router..." (which would be the AirPort Extreme in your case)
So, it appears to me that this would be the way that you must reconfigure the Westell device to allow the AirPort Extreme to function as the "main" router on your network. In this type of setup, you will be able to enter the DNS information that you want to use under the setup for the AirPort Extreme and it will act as you instruct.
The AirPort Extreme would not be configured in Bridge Mode for this....it would be configured to "Share a public IP address".
The next item in the article specifies that you "Must use a PPPoE client on the Router." This means that the AirPort Extreme would be configured to Connect Using = PPPoE as follows:
AirPort Utility - Manual Setup
Click the Internet icon
Click the Internet Connection tab
Connect Using = PPPoE
You would enter your user name (probably your email address), password, etc in this area. Leave the Service Area box completely blank. Set Connection to Always On, and Disconnect if Idle to Never
Click Update to save the new settings. Power off the Westell device after this and then restart it so that it will pick up the new information that you have programmed into the AirPort Extreme.
I want to stress that this is how I would try to configure the Westell and AirPort Extreme. But, as I said, have not used a Westell device, so I cannot say that this will work correctly for you.
It might be an excellent idea to contact Bell South or AT&T Support to ask for their opinion on this before you decide to change the configuration of the Westel device and the AirPort Extreme.
This type of thing can be intimidating for users, so you might elect to use the services of someone like the Geek Squad at Best Buy, or a similar service from a local computer firm. Perhaps the Apple store could help as well.
If it is not critical that you use Open DNS, you might want to simply leave things "as is", with the AirPort Extreme in Bridge Mode.

I am running an older airport extreme v7.6.4wireless router with a new netgear rn104 server and cant get the server to show in the MacPro hardware or the on the wireless router

How do I adjust the settings to get this Netgear server to show and use the Airport Extreme and show up on the hardware of the McPro?

The server is never going to show on the airport extreme.. it is not wireless.. unless you happen to run v5 airport utility. Most are running v6.
Is the Netgear setup for dhcp .. the display on the front of the netgear should be showing its IP address.
What is it??
What IP is your Mac getting?
I presume both are plugged into the AE by ethernet.. if not please do so now.
To open anything but Apple products like AE you open the IP in the browser.. simply type that IP on the front screen of the NAS into your browser. If it doesn't connect you have the setup wrong and something is not using DHCP.. in that case tell me exactly what you are getting.

How do I install Enabler from the Airport Extreme disk?

Recently I purchased an new Airport Extreme. One of my 3 computers is a 2 GHz Intel Core Duo iMac with 20 inch display (iMac4,1). It is running 802.11g. I wish to enable it for 802.11n. I am confused by a statement about the enabler, which is found at the following link for the AirPort Extreme 802.11n* Enabler for Mac (http://store.apple.com/us/product/D4141ZM/A?fnode=MTY1NDAzOA&mco=MTA4MjgwNzI). The statement is, "Important note: The Enabler is included free with the new AirPort Extreme Base Station with 802.11n. If you purchase a new AirPort Extreme Base Station, you do not need to purchase the Enabler separately." On my iMac, the Network Utility indicates the iMac is not enabled for 802.11n. I have kept the software on the iMac up to date. Thus I assume that somewhere on the disk that came with the Airport Extreme, there is an enabler file I need to access. Where do I find this, and how do I enable the iMac for 802.11n? Thank you.
Sincerely,
Wilson

I am still a bit confused, because the information at the link I gave seems to indicate that a person with my model of computer should be able to use the AirPort Extreme 802.11n* Enabler for Mac.
1. My computer is not a 17 inch 1.83 GHZ. It is a 2.0 GHz Intel Core Duo iMac with a 20 inch display (measured diagonally).
2. The web page (http://store.apple.com/us/product/D4141ZM/A?fnode=MTY1NDAzOA&mco=MTA4MjgwNzI) says check "Before purchasing the 802.11n Enabler software, please check to make sure that your Mac does not already have the 802.11n enabler already installed."
3. It then shows how to use the Network Utility to see whether or not the enabler is installed ("If the section "Model: Wireless Network Adapter," if it says (802.11a/b/g/n), you already have the 802.11n enabler installed. If it says (802.11a/b/g), you do not have the 802.11n enabler installed." My computer lists "802.11a/b/g".
3. Thus I assume that all now I need to do is to install the enabler, which one then can purchase, which one then can do through the Apple Store web page.
4. My issue is that the same web page says I do not need to purchase the enabler if I have already purchased the Airport Extreme base station. ("Important note: The Enabler is included free with the new AirPort Extreme Base Station with 802.11n. If you purchase a new AirPort Extreme Base Station, you do not need to purchase the Enabler separately.")
What have I missed?

Setting up TC on N (5 GHz), with older AirPort Extreme and Express on B/G

Hi there,
I've done a search through the forums (and the net) to see if I can find a solution to my query, but the answer currently escapes me so I thought I'd ask outright....
I have recently purchased a Time Capsule. Previously my wireless network relied on an AirPort Extreme Base Station (one of the older white models that looked like a UFO) over 802.11 b/g which was extended by an AirPort Express (again, non-N).
What I would very much like to do is create a setup that has the Time Capsule running 802.11 N only over 5 GHz, with the AirPort Extreme connected to it over Ethernet and still running a B/G network out with the Express.
There is a diagram here, which shows exactly what I want, but their instructions are far from complete or up-to-date with the current AirPort Utility software: http://www.appleinsider.com/articles/08/03/31/exploringtime_capsule_wifi_802_11n_and_the_5ghzband.html
However, I can't for the life of me work out how to do this. If someone could help me out I would very much appreciate it.

For the TC, I suggest that you change the Radio Mode to: 802.11n only (5 GHz) - 802.11n only (2.4 GHz).
For the AEBS & AX, I am assuming that you still want them as an extended wireless network ... correct? If so, all that would need to change is the following for the AEBS:
o Connect the AEBS directly to one of the TC's available LAN (opposing arrows) ports by Ethernet. Connect this Ethernet cable to the WAN (circle-of-dots) port on the AEBS.
o Reconfigure the AEBS as a bridge. (ref: AirPort Utility > Select the AEBS > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode))
o You may want to rename the AEBS/AX wireless network with a new Network Name (or SSID). This is totally optional, but may prove helpful as a reminder that you only want non-"n" clients to connect to it. For example, and with absolutely no imagination on my part, you could name your TC's wireless network: My Really Fast Network, and the AEBS/AX's: My Not So Fast Network.
o Finally, you will want to be sure the the AEBS/AX wireless network is at least 3-5 channels away from the 2.4 GHz network provided by the TC. This will prevent any Wi-Fi interference between them.
The WDS settings created earlier when you configured the AEBS & AX for an extended network should remain the same.

How do I set up a Netgear WNR3500 as wireless extender with the Airport Extreme as my main router?

Similar Messages

Maybe you are looking for