How do I set up a network printer an an in-OS driver in Windows 7 32 bit?

What printer? What router?
Get the latest software for your printer from the "Support & Drivers" link at the top of this page.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

How do I set up my dx7400 printer to iPhone 4s as I have no pc or lap top?

How do I set up my dx7400 printer to iPhone 4s as I have no pc or lap top?

You don't.
According to Epson ( http://www.epson.com/cgi-bin/Store/support/supAdvice.jsp?BV_UseBVCookie=yes&type =highlights&noteoid=196563#epson_connect_compatibility ) That printer does not support AirPrint.

How do I set up my Epson printer to print wirelessly from my Mac Pro

How do I set up my Epson printer to print wirelessly from my Mac

Hello:
You need to go to Epson for specifics (is your printer set up for Airprint, etc).
Barry

How do I set Ipad up to print from hom PC?

How do I set up Ipad2 to print from how PC?

To print from an iPad, you will either need an AirPrint-enabled printer or use a software solution, like Printopia. Unfortunately, Printopia I believe only works with Macs so it would not be a viable option in your case.

How do I set up automatic duplex printing for my HP Laserjet Pro400 M401n series?

How do I set up automatic duplex printing for my HP Laserjet Pro400 M401n series from my PC using windows 8?

Thanks for your reply.
Looks like I didn't do enough research as the HP site said it's available however upon further investigation only manual duplexing is available with drivers installed.
http://www8.hp.com/ca/en/products/printers/product-detail.html?oid=5166605
Drive productivity and save paper, using automatic two-sided printing

I have Mac OS 10.8.5 and Acrobat X 10.1.9. how do I set up as PDF printer?

I have Mac OS 10.8.5 and Acrobat X 10.1.9. how do I set up as PDF printer?

during installation of acrobat a virtual pdf printer is installed.
when printing you should see an option to print to a pdf file. if you don't, reinstall.
you might need to uninstall, clean your system and then reinstall, http://labs.adobe.com/downloads/acrobatcleaner.html

How can I set up a preferred printer so I don't have to pick the printer each and every time I print something out? At the moment, even immediately after printing one thing, it prompts me to pick a printer, which is very time consuming.

How can I set up a preferred printer so I don't have to pick the printer each and every time I print something out? At the moment, even immediately after printing one thing, it prompts me to pick a printer, which is very time consuming.

Compass Health Systems wrote:
How can I set up a preferred printer so I don't have to pick the printer each and every time I print something out? At the moment, even immediately after printing one thing, it prompts me to pick a printer, which is very time consuming.
No, there is not setting for a default printer.The system scans for available airprint printers each time you print.

I want to connect to a network printer hp cp1518ni with different versions of windows (win7& winxp)

I want to connect to a network printer hp cp1518ni with different versions of windows (win7 & winxp) . My pc with win 7 work ok but the pc with win xp not "see" the printer on the network. What is the additional driver should I install?
thanks
This question was solved.
View Solution.

Hi @OHIMATAS,
I see by your post that you are unable to network the printer to the Windows XP computer, but the Windows 7 computer is connected. I can help you with this.
Make sure the Windows XP computer is connected to the correct network name, not a Guest network either.
Print a configuration page to get the printer's IP address.
Printing a Configuration Page.
Try and access the printer's Embedded Web Server on the Windows XP computer.
Type the IP address into your web browser's address bar. (Internet Explorer)
Did it load the webpage?
If you can't access the printer's EWS, then check the IP address on the computer to see if the first 3 sets of numbers match the printer's IP. They have to match to be on the same network.
Go to start, type run in the search box, type in cmd, then type ipconfig.
Check the IPV4 address.
Now check the IPV4 address for the printer.
Do the first 3 sets of numbers match?
Try and ping the printer.
In the same window, type ping printers IP address (space between ping and IP address)
What are the results?
Run the add printer wizard through printers and faxes, if you were able to access the printer's EWS.
Please provide in detail the results if you are still having issues.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

HT4759 How do I set up icloud for my ipod shuffle on my new computer windows 8. I downloaded the icloud but it tells me that i don't have the icloud and I cannot add songs to my ipod.

How do I set up icloud for my ipod shuffle on my new computer windows 8. I downloaded the icloud but it tells me that i don't have the icloud and I cannot add songs to my ipod.

An iPod Shuffle can't use iCloud. It can only be used on an iOS device (iPhone, iPad or iPod Touch) running iOS 5 or higher, or on a supported Mac or PC.
Also you can't create and iCloud acount on your PC (or your iPod Shuffle). You have to create your account on an iOS device (iPhone, iPad or iPod Touch) running iOS 5 or higher, or on a Mac running OS X Lion (10.7.2) or higher. After creating the account on one of these devices you can sign into it on your PC. But this still won't allow you to add songs to your iPod Shuffle as it doesn't support iCloud.

How do i connect to a network printer or map a network drive?

I have a MacPro on my work network and can only attach to the networked printer via IP address. The printer driver is on the print server and I have a path name but I do not know where in my MAC to input the network path/drive.

First install the printer driver on your Mac. Then add the printer in System Preferences > Print & Scan. Beyond that, specific settings for the printer & protocol depend on the printer & network. You may need to call your helpdesk for assistance. Exactly what make/model printer is it, and how is it set up on your network?

How do I set up a Canon printer that is asking for a WPS button?

I am trying to set up a Canon printer and cannot figure out how to do it with Airport Extreme as they are asking for a WPS button to be pushed....Please Help!

What operating system is being used on the computer that is configuring the printer and AirPort Extreme?
Apple has not supported the WPS type of setup for some time, so it may likely be necessary to use the manual setup option to configure the printer. Check the printer documentation for that procedure.
In this type of setup, the printer connects just like a laptop. You search for the wireless network, select it and enter the password to connect.

How do I set up for Wireless printing on a Mac

Hi Guys,
I have purchased the HP Laser jet P1102w recently. I took the printer on a location job and used it for the first time. It was quite a soimple process of connecting the printer and MAC automatically downloaded and installed the software.
As we were out of the office, we were not connected to the wireless network and therefore was not able to set up the printer on the netwrok.
Now that we are back in the office I want to set up the printer so that it can be used wirelessly by all the devices connected to the network.
I am unable to work out how to do this on MAC OS X 10.6.8. I removed the printer from the Print & Scan Utility and tried to install it again while connected to the network, however I am still only able to print while connected by USB.
I understand that I can print via the connected device on the network but would rather have it set up to do so wireless all together.
Please can you point me in the direction of finding the instructions to set this up?
All help is most appreciated.
This question was solved.
View Solution.

Hi @EI2014 ,
Make sure Safari is set as the default browser. Sometimes the Embedded Web Server won't open in other browsers.
Open Safari, across the top select the Safari menu, select Preferences, General, set as default.
Clear out any old network settings on the printer.
Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
Print out a configuration report and make sure the SSID and IP address are cleared.
Printing a Configuration Page.
Connect the USB cable from the printer to the Mac.
Go to the Apple, system preferences, print and fax.
Double click on the P1102w.
Open the utility.
Click printer setup.
Click HTML config.
This should open the Embedded Web Server for the printer.
Click the Networking tab.
Click Wireless from the list on the left.
Under Communication Mode , click Infrastructure.
Select your network SSID from the Available Network Names (SSID) list and then click the << button so the network name moves over to other box.
From the Security Mode pop-up menu under Authentication , click WEP, WPA/WPA2 or open . Your selection depends on which Wireless Security Protocol your network uses.
Make sure you select either hexadecimal or alpha depending on your password. (very important)
Apply the settings.
In the confirmation box (changes have been saved), click OK.
You should get a solid blue light on the printer shortly.
Then all we have to do is delete the USB driver and add the network driver.
Click on the Apple.
Click system preferences.
Click the print and fax icon.
Highlight the printer and click on the - sign to delete the printer. (USB driver)
Disconnect the USB cable.
Then click the + sign and select the printer from the list and click add. (p1102w bonjour)
Test the printer.
If you have any issues with the HTML config opening then do the following steps:
Close any applications.
On the Apple menu bar, click Go, computer, MAC harddrive, Library, Printers, HP, LaserJet, click on folder for your printer, click on EWS browser or HTML config, click the Networking tab, click wireless on the left and fill out your information. (make sure infrastructure is selected) Apply settings.
Then delete the USB driver and add the network printer.
Test the printer.
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Setting up a Network Printer

I have 3 iMacs set up to a 2Wire DSL modem and wireless router from AT&T. I have a HP jet direct 175x router plugged in via ethernet to the router. i have a HP deskjet 5440 plugged into the jet direct.
i used to be able to find the printer when i would go to printer setup. now i can't find it anymore. i can only print when i plug the printer directly into the imac.
how can i get the network printing functionality to work again??? everything i try (turning off everything, appletalk is on because my internet works fine, etc.)

Though not required, appletalk is a useful "autodiscovery" protocol for Jetdirect print servers.
(Apple has announced "eventual" phaseout of appletalk - but they haven't said when.)
Use the IP printer > HP Jetdirect protocol to add {+} the printer in Print & Fax prefs.
However, the HP-provided driver won't work for network protocols - It was written for USB only. Get the 3-part hpijs driver set:
http://www.linuxfoundation.org/en/OpenPrinting/macosx

How do i set up my e print to print in color

How do I set up my printer to print in color ?

Hi,
On my printer, I set it to print in color then it will print in color. You can do the same for your printer. Millions of them are out there, what is yours anyway ? To help us answer question quicker, please read this:
http://h30434.www3.hp.com/t5/First-Time-Here-Learn-How-to/Welcome-Get-started-here/td-p/699035
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

How do I set up a network hard disk so I can restart my MacBook from it?

I have a 2TB Freecom XS Network hard disk, and I want to be able to restart my MacBook from it with my current OS, Leopard 10.5.8, when I have upgraded the OS on the MacBook to Snow Leopard 10.6.3 [as a possible precursor to Mavericks or even Yosemite]. The problem is that the MacBook doesn't recognise the XS as a network disk: the XS has been assigned an IP number, and I can mount it as a server volume, and I have copied all the system folders/files onto it, but that is no use if the system doesn't recognise it as a network disk for a restart [I've tried]. The system/library/users/applications folders are in a Macintosh HD folder as on the MacBook, but this folder is inside a root folder named PUBLIC: could this be part of the problem? I thought I might be able to reinstal the OS on the network disk using the original system installation discs, but after restarting the MacBook as instructed, the network disk isn't recognised as a destination for installing the OS. I don't want to instal Snow Leopard on the MacBook before I'm sure I can reboot it with Leopard, using the network disk.

Hi BDAqua.
Thank you for your reply. I don't know how much what I omitted to disclose in my original post might affect what you've told me, but I have a wireless network set up with a 500GB Time Capsule, to which a broadband router and another backup disk [1TB, daisy-chained to the TC] are connected. Given the difficulty I had initially, setting up the network [mainly because of my ineptitude where comms are concerned], I didn't want to risk connecting the Freecom drive to the TC, in case it changed the network settings [or worse, disrupt my internet access], and I haven't done it hitherto. I did try connecting the ethernet cable to the wireless router however, with neutral results: still possible to manually mount the drive as a server, and it shows in the Network folder in my MacBook's root folder.
Further to an email from Freecom's support department [effectively just a request for part number, proof of purchase, etc.], I followed their suggestion and tried connecting the drive to the MacBook using the USB 2 cable, and the drive showed up in the device section of the Finder window sidebar, but I would guess that this option wouldn't enable the drive to function as a boot drive either? Also, unless I'm mistaken, USB offers much slower data transfer speeds than Gigabit Ethernet? I'm hoping I've not dropped a monumental bollock, because I'm positive from my pre-purchase research that Gigabit Ethernet is faster than FireWire or USB2, which is why I chose this drive over cheaper USB drives [like the 1TB Western Digital drive daisy-chained to the TC]; or am I mistaken?
To get back to your answer though, I don't dispute what you say, because I'm sure I'm much less of an expert than you might be, but I would nevertheless like to be able to boot up from the Freecom drive, if a way to do that is possible, even if it means biting the bullet and connecting it to the Time Capsule [assuming that this will work: can you advise?], without needing to investigate and purchase additional kit. I've had a scan of the forum, and I've seen a few suggestions which mention cloning, but I don't know how this works: I presume I'd have to buy the appropriate app for that? Your answer seems to suggest installing the new OS onto an external drive [although, worryingly, you don't mention Ethernet as an option] using cloning, so I'd be grateful if you could explain that.
I just hope that my desire to save the cost of a newer Mac of some description, be it new or refurbished, but giving me the newest OS possible on the MacBook [Yosemite, I'm guessing], doesn't end up costing me something uncomfortably similar, cumulatively.
Any practical and reasonably-priced suggestions welcome and considered! Thanks again

How do I set up a network printer an an in-OS driver in Windows 7 32 bit?

Similar Messages

Maybe you are looking for