How do I set up a network using time capsule

I have a 2TB time capsule and an airport express, however I would like to move my capsule to another room where I want to connect 2pc's, which do not have wireless adapters and connect them via Ethernet to the capsule to allow them to go online. My printer is in this room currently connected to airport express to print wirelessly, but I want to put my airport back on my stereo.
In addition I want to continue backing up my iMac, wirelessly, the problem i am experiencing is the time capsule needs to be connected to the router via Ethernet.
Moving the capsule to the other roodoes too far, without a direct route to run Ethernet cable.
Can this be done? Any help is very much appreciated.
Cole

Hi Bob,
I have an O2 router wireless box 5
In short what I would like to acheive is;
iMac - wireless connection, wireless printing, wireless back up to time capsule
Time Capsule - conect to printer via usb and to connect 2 pcs via ethernet to use Internet and print
Thanks for looking into it for me
Cole

Similar Messages

Best way to set up home network using Time Capsule

Hi
My current home network consists of Macbook Pro 17 connected wirelessly, another Mac and few pcs. I have a Time Capsule, new netgear router and several hard drives. At the moment my main drive is plugged in via usb to the mac, however id like to set up a proper mini network where i can at least share several drives between macs, HOWEVER i also want to back up this data via TC, which is why at the moment my hard drive is plugged into the mac, so it can be backed up. Am i correct is saying that TC will not backup netwrok drives?
..any suggestions for best way to set up a network with TC backing up drives?
Thanks

paulsutt wrote:
Am i correct is saying that TC will not backup network drives?
Yes.
..any suggestions for best way to set up a network with TC backing up drives?
You could share the locally-connected drive. That would require that your Mac be on whenever any other network client needed to access the drive.

How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

Sorry, but it is not possible to "extend" the Guest Network using either wireless or an Ethernet connection.

I connected my Canon printer to time capsule, and can print OK. However, I can't get the printer scanner to work. How do you set up the scanner with Time Capsule?

I connected my Canon printer to time capsule, and can print OK. However, I can't get the printer scanner to work. How do you set up the scanner with Time Capsule?

You cannot use USB. It has to be a network capable printer.. is it?? You did not indicate how it is connected.. but by wireless or ethernet then scanning is possible otherwise not.

How can i extend a wireless network with time capsule

How can i extend an existing wifi verizon wireless network with time capsule? the router is connected on the bottom floor. want to boost the signal to a home office on the top floor, four flights up. connect time capsule via ethernet cable to iMac on 4th floor? Do I have to start a second wifi network or can I set it to just boost the one I have? thank you

How can i extend an existing wifi verizon wireless network with time capsule?
It all depends on what you mean by "extend".
If you plan to "extend" by connecting the Time Capsule to the Verizon router using a wired Ethernet cable, this can be accomplished.
If you were hoping to connect the Time Capsule to the Verizon router using wireless only, unfortunately the Time Capsule and Verizon products are not compatible for that purpose.
Check with Verizon to see if they offer an "extender" or "repeater" that could be located very close to the Time Capsule.
This would provide both more wireless coverage and also allow you to connect the Time Capsule using an Ethernet cable from the "extender" or "repeater".

WiFi network security: How do I create a hidden SSID using Time Capsule?

Hello. I'm having a security issue on my wireless network. I recently noticed (via a Finder window under "Shared" on the left side of the window) someone squatting on our wifi network which is WPA encrypted and is based on a Time Capsule plus 2 Airport Express boxes for streaming music. I have an external network drive connected to the Time Capsule which houses all my iTunes music and movies. I have a feeling they are breaking in to steal from that rather than merely using our internet connection. I immediately changed the password. The next day I found them on our network again. I changed the password again. Immediately after changing the password and refreshing the Finder window, they showed up on our network yet again. I then changed the name of our SSID/wifi network and the password for a 3rd time. So far they haven't showed up and I'd like to keep it that way. We live in an apartment building and I fear that they won't see our old network name in the lists of networks and will realize that the new network name is us and then they will break in yet again.
1. is there anything else I can do to stop them?
2. is it a good idea/solution to hide our SSID and if so, how do I do that on the Time Capsule?
I can't seem to find any info on creating a hidden SSID on the discussion boards so any help is appreciated. Thank you!

If you have other devices on your network and have enabled file sharing on them, you will see an occasional device or two come and go. That is normal. Usually, you'll see something with some numbers. That's usually the last 6 digits of the MAC address of a device.
Any hacker who is smart enough to crack your network is not going to allow his identity or any trace of his computer to be displayed on your network.
If you are still convinced that someone is cracking your network, you can enable the "closed" network option, but there are plenty of free utilities on the Internet available that will reveal a "closed" network in seconds. Most 12 year old kids looking for free wireless know how to do this.
If you want to do this anyway, here is how:
Open AirPort Utility - click Manual Setup
Click the Wireless tab below the icons
Click the Wireless Options button
Enter a check mark next to "Create a closed network"
Click Done, then click Update and wait for the Time Capsule to restart
Message was edited by: Bob Timmons

Creating network using Time Capsule, Airport Extreme and Airport Express

Hello,
Yesterday I purchased the 4th Gen Time Capsule to replace my Airport Extreme (4th gen) as my "main" router. However, I want to repurpose my Airport Extreme to extend the network AND use the Ethernet ports to connect additional devices. I will then use my Airport Express solely to "join the network" for Airplay purposes.
I connected the Time Capsule directly to my cable modem using Ethernet. I set up the Time capsule in Airport, checked the "allow this network to be extended" and used WPA2 Personal encryption. I then set up the Airport Extreme to "join an existing network" wirelessly and mimic the same network name, encryption type and password. Finally, I set up the aiport express as I mentioned above.
This setup does a great job of extending my network with increased performance. However, when I plug my Mac into the Airport Extreme using ethernet, it does not recognize. This Mac IS connected via Aiport. However, under the "ethernet" option in the Network Menu, it says "No IP Address Found."
I've searched some other forums and thought this configuration would work. Also, I apologize if this seems like and amateur post. This is my first time using the Apple support Community.
Thank you

I set up the Time capsule in Airport, checked the "allow this network to be extended" and used WPA2 Personal encryption
Those are the correct settings for the "main" router.
I then set up the Airport Extreme to "join an existing network" wirelessly and mimic the same network name, encryption type and password
The AirPort Extreme does not provide any additional wireless coverage and the Ethernet ports are not enabled if the device is configured to "join a wireless network"
Check your setttings using AirPort Utility - Manual Setup
Click the Wireless tab located just below the row of icons
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the Time Capsule wireless network
Enter a check mark next to "Allow wireless clients"
Wireless Security = Same setting as the Time Capsule wireless network
Wireless Password = Same password at the Time Capsule wireless network
Confirm Password
Click Update at the lower right and allow 25-30 seconds for the AirPort Extreme to restart.
Configured correctly, the AirPort Extreme will extend the wireless network and the Ethernet ports on the Extreme will be enabled.
I good starting location for the extending device is a location about 1/2 to 2/3 the distance from the main router to the area that needs more wireless coverage.
Once you have the AirPort Extreme configured and working correctly, post back if you would like a tip to find out exactly which device....your Time Capsule or the AirPort Extreme that your laptop is connected to at any given location.

Settings for Roaming Network using Time Capsule plus old Airport Extreme

Hi all
I am trying to set up a network in the most effective way for my home and am experiencing some difficulties which I hope your support can help me overcome.
My home is constructed of concrete reinforced with steel and consequently the walls are dense and wireless signals are adversley affected. I have two wireless base stations via which I hope to provide wireless coverage to my whole home which is on the ground floor level only. My Time Capsule is located at one end of my home and is directly connected to my modem which receives the external fibre optic supplied internet connection. The Time Capsule is managed via Airport Utility 6.1. A mac is connected to the Time Capsule via ethernet cable - the Time Capsule also provides a wireless signal. Also connected to the Time Capsule via a long ethernet cable that is routed in internal cable channels within my home is an old conical shaped white Airport Extreme. The Airport Extreme is located at the other end of my house and also has a mac connected to it via ethernet and provides a wireless signal too. The Airport Extreme is managed via Airport Utility 5.6.
I hope to have a wireless network that my iphones and ipad can connect to in various areas of the house. I have read the instructions for setting up a Roaming Network, yet the screen shots provided do not reflect the screens I see using Airport Utility 5.6 and 6.1. Can anyone please assist with the settings that I require?
Also I have a question regarding a roaming network - if I connect a mobile device to the wireless network near to my Time Capsule and then move to the other end of my house near to the Airport Extreme what should happen to the wireless connection strength? Currently with my existing settings the mobile device is maintaining the connection to the Time Capsule and dropping to extremely low connections levels rather than picking up the wireless signal from the Airport Extreme. Should this be the case and if so is there some better way to set up my network?
Originally I had the Airport Extreme configured in a different location closer to the Time Capsule to extend the wireless network from the Time Capsule. The problem was that the Airport Extreme frequently seemed to not provide the newtork. I'm not sure if it lost the network from the Time Capsule or had some other problem.
All help will be greatly appreciated.

So just to be clear.. the Mac at the other end of the house.. has internet connection.. via ethernet.. through the old extreme.. ethernet to the TC.. which is connected via ethernet to the fibre connection.
Is the airport extreme in bridge mode?
As long as it is, you are good to go.
On both the TC and AEBS you create a wireless network.
On both TC and AEBS you name it the same.. eg 24ghz (please use short, no space, pure alphanumeric name).
You set both with the same security.. WPA2 Personal
You set both with the same passkey.. 8-12 characters pure alphanumeric.
BUT you set the wireless channels.. there are three channels that do not overlap.. 1, 6, 11 (13 in europe ME??)
Suggest you set TC to 6.. and set the AEBS to 11.
It might work on auto but IMHO wireless is something you are better controlling than leaving it to dumb algorithm

Extending an existing wireless network using Time Capsule

I connected my Time Capsule via Ethernet cable to my network. I used the airport utility to extend my existing wireless network (Cisco router)k. After that my wireless devices were disconnected and I got a message stating "Unable to join wireless network". The macbook that I used to set up the Time Capsule showed a message along the lines that a device on the network was trying to use the macbook's IP address, I changed the macbooks IP address and then was able to connect my ipad and iphone to the wireless network but the connection was unusable as it was so slow. has anyone done this successfully and if so do you have nay advice

If you connect the TC to the network by ethernet you do not extend an existing networking.. indeed you cannot.. only works with apple routers and no ethernet.
You create a wireless network.. you can use roaming .. ie use the same wireless name and security settings as the existing Cisco router but you must set different channels.
If you need instructions in that setup what version airport utility are you using. I would strongly recommend a version 5.. it is so superior cf toyland v6.

Extending wireless network using Time Capsule

Hi guys,
I have been trying to sort this issue out for some time.
Basically I have a Thompson Wireless Router which connects to my ISP, this is downstairs broadcasting a wireless network to my house.
I want to put the Time Capsule upstairs, to extend the WLAN and also connect my Xbox over Ethernet.
No matter what I try I cannot get it to work, it ends up setting up 2 WLANs where the Thomson WLAN works (as there is an ISP connection) and the TC wont (as its not connected)
What I want is for the Thomson WLAN to be extended via the TC to allow my Xbox on to Live...
I also have a Mac Mini upstairs that would connect either via the TC WLAN or through ethernet.
Any help you can offer would be amazing
Thanks
Adam

If you are trying to "extend" the wireless signal from the Thompson router through the Time Capsule using wireless only, this is probably not going to work.
The reason for this is that Apple's "extend a wireless network" feature appears to be a proprietary technology that works only among other Apple devices. For that reason, it is highly unlikely that the Thompson router and Time Capsule would be compatible for the purpose that you desire.
If you are able to connect the Time Capsule to the Thompson router using an Ethernet connection, you could configure the Time Capsule to "create a wireless network" using the exact same wireless network name, security settings and password as the Thompson network. In addition, the Time Capsule must be configured as a "bridge" in Bridge Mode for this to work correctly.
If you cannot run the Ethernet cable, you might want to look at a pair of Etherent powerline adapters to accomplish the same task by sending the Ethernet signal over the existing AC powerlines in your home.

Wired network using Time Capsule

I'm building a new house soon and want to maximise the wired and wireless networking opportunity while I've got the chance. We currently have two MacBooks and an iMac in the household, plus iPhone, iPod and iPad. I have a 1TB Time Capsule which I currently use as a router, very satisfactorily, wired and wireless.
I want to incorporate wired network access points in five or maybe six different rooms, share at least two printers across the network, and enable wi-fi throughout the house for the other portable devices and guest access. Our TV will be "internet-ready" with a built-in ethernet port. I'd also like to be able to play music from mobile devices, wired and/or wirelessly, to an output such as a Bose Wave Radio (which has an AUX jack), and the TV.
I'm looking for the optimum solution to integrate all these things, starting with the need to add additional ethernet ports to the Time Capsule. I'd be quite happy to buy a second TC if needed, as it would give me addiitonal back-up storage for the future.
All suggestions welcome! Thanks!

Dear LaPastenague - sorry to go off topic: please advice me how to reciver
passwors to enter my Time Capsule's server ? You are very knowledgeble as I see. And I am not. Need help, please!
I am trying to transfere all my settings and everything from my Timemachine to a cleaned up MacBookAir - due to it recent freez and corrupted all and start-up problem... Password was on a Note page and it was wiped up too.
It asks: Enter your password to server "svetlana's Time Capsule" so that Time Machine can access it.
I have connected TM and laptop by wire today (network to USB) - but same question pops up.
Thank you!
Sorry Nail_P to enter your topic with this message...Don't know how to contact LaPastenague better.

I have a m2007 macbook connected to my wireless network using time capsule. I stream video to the macbook, but often get start stop of the streaming, but no wheel to indicate a buffering issue. Can I resolve this with higher speed internet and cable mod

I'm wondering if my cable internet is too slow for wireless streaming of videos to other macbooks. Any help will be appreciated

Can you clarify whether you are asking about video that you are streaming from the Internet to your Mac through the Time Capsule?
Or, are you asking about streaming video that is already stored on the Time Capsule to your Mac?
In either case, what happens....video quality wise..... if you test by temporarily turning off the wirelss on the Mac and then connecting it to one of the LAN <-> ports on the Time Capsule using a spare Ethernet cable for a few hours?

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

How do I set up a network hard disk so I can restart my MacBook from it?

I have a 2TB Freecom XS Network hard disk, and I want to be able to restart my MacBook from it with my current OS, Leopard 10.5.8, when I have upgraded the OS on the MacBook to Snow Leopard 10.6.3 [as a possible precursor to Mavericks or even Yosemite]. The problem is that the MacBook doesn't recognise the XS as a network disk: the XS has been assigned an IP number, and I can mount it as a server volume, and I have copied all the system folders/files onto it, but that is no use if the system doesn't recognise it as a network disk for a restart [I've tried]. The system/library/users/applications folders are in a Macintosh HD folder as on the MacBook, but this folder is inside a root folder named PUBLIC: could this be part of the problem? I thought I might be able to reinstal the OS on the network disk using the original system installation discs, but after restarting the MacBook as instructed, the network disk isn't recognised as a destination for installing the OS. I don't want to instal Snow Leopard on the MacBook before I'm sure I can reboot it with Leopard, using the network disk.

Hi BDAqua.
Thank you for your reply. I don't know how much what I omitted to disclose in my original post might affect what you've told me, but I have a wireless network set up with a 500GB Time Capsule, to which a broadband router and another backup disk [1TB, daisy-chained to the TC] are connected. Given the difficulty I had initially, setting up the network [mainly because of my ineptitude where comms are concerned], I didn't want to risk connecting the Freecom drive to the TC, in case it changed the network settings [or worse, disrupt my internet access], and I haven't done it hitherto. I did try connecting the ethernet cable to the wireless router however, with neutral results: still possible to manually mount the drive as a server, and it shows in the Network folder in my MacBook's root folder.
Further to an email from Freecom's support department [effectively just a request for part number, proof of purchase, etc.], I followed their suggestion and tried connecting the drive to the MacBook using the USB 2 cable, and the drive showed up in the device section of the Finder window sidebar, but I would guess that this option wouldn't enable the drive to function as a boot drive either? Also, unless I'm mistaken, USB offers much slower data transfer speeds than Gigabit Ethernet? I'm hoping I've not dropped a monumental bollock, because I'm positive from my pre-purchase research that Gigabit Ethernet is faster than FireWire or USB2, which is why I chose this drive over cheaper USB drives [like the 1TB Western Digital drive daisy-chained to the TC]; or am I mistaken?
To get back to your answer though, I don't dispute what you say, because I'm sure I'm much less of an expert than you might be, but I would nevertheless like to be able to boot up from the Freecom drive, if a way to do that is possible, even if it means biting the bullet and connecting it to the Time Capsule [assuming that this will work: can you advise?], without needing to investigate and purchase additional kit. I've had a scan of the forum, and I've seen a few suggestions which mention cloning, but I don't know how this works: I presume I'd have to buy the appropriate app for that? Your answer seems to suggest installing the new OS onto an external drive [although, worryingly, you don't mention Ethernet as an option] using cloning, so I'd be grateful if you could explain that.
I just hope that my desire to save the cost of a newer Mac of some description, be it new or refurbished, but giving me the newest OS possible on the MacBook [Yosemite, I'm guessing], doesn't end up costing me something uncomfortably similar, cumulatively.
Any practical and reasonably-priced suggestions welcome and considered! Thanks again

I was using time capsule to extend a network. now i want it to be the primary base station. how do i convert this?

i was using time capsule to extend a network. now i want it to be the primary base station. how do i convert this?

Thanks for the info. Since this is a cable modem, you will need to fully reset it so that it will associate correctly with the Time Capsule when it is reconnected.
I don't have the manual for your Ubee model handy, but most modems will reset if you power them down completely. That means pulling the power cord from the back of the device or unplugging from the wall. Leave the modem powered off at least 30 minutes...longer will not hurt a bit.
Next, perform a Factory Default Reset on the Time Capsule per this document:
Resetting an AirPort Base Station or Time Capsule FAQ
After the modem has been powered down and Time Capsule has been reset, connect an Ethernet cable from the modem to the WAN port (circle icon) on the Time Capsule.
Power up the modem and let it run for 2-3 minutes by itself
Then power up the Time Capsule and let it run a minute or two
Next, open AirPort Utility and configure the Time Capsule to "Create a wireless network". Let us know what operating system you are using on your Mac or PC if you have additional questions or need more details on this.

How do I set up a network using time capsule

Similar Messages

Maybe you are looking for