How do I set up a PCI-DNET card as master with A-B DNI as slave?

I'm trying to communicate with an Allen Bradley PLC through DeviceNet. I have a NI PCI-DNet card in my computer, and an Allen-Bradley 1761-NET-DNI interface between my PLC and the DeviceNet network. Does anyone know how to set up my National Instruments card as the Master of my PLC/DNI combination? Thanks in advance for the help.
Mark

Hi Mark:
The PCI-DNET card should set itself up as the master by default. As a matter of fact it should take more work to get it be the slave than to get it to be the master. Is this not what you are experiencing? Is there some sort of Allen-Bradley software that you have installed that is not allowing the NI board to be the master?
The DNET Manual states on page 4-8 that NI-DNET assumes that it is the only master in your DeviceNet system.
Emilie S.

Similar Messages

Setting up PCI-DNET card to work with Eurotherm 2404 Controller w/Device Net

I have installed the NI PCI-DNET card in my PC running W2000 and the NI Measurement and Automation Explorer. I have also wired from the PC Card to a Eurotherm 2404 Controller with a Device Net Module and have terminated the connection with a 120 Ohm termination resistor. The baud rate and address have been configured on both ends to match, however although I am getting a good connection to the board I am not able to pick up the device when I run the "Simple Who" funtion. Any advice would be greatly appreciated.
Thank You

Hi,
When you say “…address have been configured on both ends to match”, do
you mean that you set the ‘Interface MAC ID’ of the dialog that comes
up when you start Simple Who to the one that is used by the Eurotherm
2404 Controller?
Simple Who is a master/scanner in a DeviceNet network, thus the
‘Interface MAC ID’ you configure is the one of the master, which must
not be identical to the one of any slave devices in the network. So,
try setting the ‘Interface MAC ID’ to a value other than the one used
by the Eurotherm 2404 Controller.
-B2k

How do I set up airport on my macbook pro (wired with ethernet to cable modem) and my ipad2 to use ipad wifi?

How do I set up airport on my macbook pro (wired with ethernet to a cable modem) and the wifi settings on my ipad2 to enable the use of wifi on my ipad?

http://docs.info.apple.com/article.html?path=Mac/10.5/en/8156.html

How do I set up my new Macbook Pro to associate with my Apple ID so I can download purchased music?

How do I set up my new Macbook Pro to associate with my Apple ID so I can download purchased music?
Under 'Manage Devices' it only lists my iPhone and iMac. I've bought stuff on my new Macbook Pro using my Apple ID, but I can't find music I previously purchased using the iMac.

Oh, wait, I've found it. Silly me!

HT2731 How do I set up an Apple ID for a child with gift card credit

How do I set up an Apple ID for a chld with a gift card credit, without credit card details and without using my own account?

Go to the main iTunes Store page (within iTunes), click on the "Redeem" link on the right side of the page, click "Create Apple ID", and enter in the code from your card when requested. You should be able to create an iTunes Store account for your child without needing a credit card. You'll just need an email address for him/her to create the ID, though it can be a "temporary" one that you don't intend to really be used. You can change the email address to which receipts are sent to an account you really wish to use.
Regards.
Message was edited by: varjak paw

How can i set up mac mail so each line starts with a capital letter?

how can i set up mac mail so each line starts with a capital letter?

I am pretty sure that this is not an option within Apple Mail.

Need hardware drivers (Only!) for NI PCI-DNET card, P/N 184726E-11. Do not need Labview run-time, Silverlight etc.

I need to install just the Windows XP hardware device drivers for my PCI-DNET card, P/N 184726E-11. Ordered under P/N 777358-01, the card is boxed with an installation CD-ROM. CD-ROM is NI-DNET for windows Ver 1.6.7. When the install app runs, it is trying to install all sorts of stuff I do not need - Labview Runtime, Microsoft Silverlight, Development Support, Automatic Updaters, etc. This card is being installed in a "production" machine. We have our own software, already developed, that talks to the card via the O/S. The hardware/device drivers are most certainly on the CD-ROM, I just need them identified and instructions for installing them.
Thanks,
Ed

Thank yor for the reply. However, it is not what I am looking for. The suggested download is 406MB. That's everything but MS Silverlight and the kitchen sink - overkill for our needs. We only need to install the Windows system driver for the card. We do not need Labview RT and the other development/support stuff for this installation. We have our own communications software that talks directly to the hardware, via the windows system driver. I have the 1.6.7 software CD-ROM, and need to know where the Windows sytem hardware driver/driver installer is located and what is the preferred method for installing only the hardware driver.
Thanks,
Ed.

How do I set up an e-mail account to go with iPhoto?

How do I set up an e-mail account to go with iPhoto?

Applications > Mail
If you haven't set up a mail account, it will probably ask you if you want to set one up, but here's how I do it.
Press command-, and that will take you to preferences.
Up near the top click the "Accounts" tab
Click the plus button that is located at the lower left corner.
Enter your name, email address, and password.
Click enter then click continue
Set the account type to POP or IMAP. Whichever one you want is fine as long as it works with your email service.
Don't change the next security settings. Click continue.
Enter something for the description. Make sure that the "Use Athentication" checkbox is checked. Enter your password and click continue.
Click continue you might have to go through one of the security settings again. Click continue.
An account summary will come up. Click "Take account online". Then click create.
You have added your account to Mail.

My wife changed start up somehow. Now 7 or 8 files open when restart. Have to close all to do anything. How do adjust setting so that it open do normal screen with icons etc?

my wife changed start up somehow. Now 7 or 8 files open when restart. Have to close all to do anything. files, applications, internet, folders etc. How do adjust setting so that it open do normal screen with icons etc? before this, it started up and went to main screen with dock, save folders ICOns etc

I use internode and imap. When the ipad deletes emails it also removes them from the mac. How can I reverse this so the mac is the master and the ipad is the slave?ipa

I use internode and imap. When the ipad deletes emails it also removes them from the mac. How can I reverse this so the mac is the master and the ipad is the slave?

Thanks for the info. - I now know that deletion works both ways!! - (unlike POP where emails deleted from the ipad also deleted them from the mac even before I could read them, whereas emails deleted from the mac were not removed from the ipad!!! - ie. the ipad was the master over the mac - the slave). Prior to changing to imap I used to transfer all nongarbage emails from inbox to mailboxes before my husband could ask if he could delete emails on his ipad. I have noticed however if you do this in imap, they are removed from the inbox on the ipad as well (this did not happen with POP). So we still have to check but the number is less so we like imap better than POP.
Thank again

How do I set up IPad 2 and 2-4s IPhones with Apple?

I have a 32 GB IPad 2 and ITunes on my Windows computer and just ordered 2-16 GB 4s IPhones for my wife and myself I have 18.5 GB of data on my IPad, but only want to selectively include some of the applications and music on my IPhones. I have IOS5. Both IPhones will be loaded with appx 10 GB of data, but each will have different applications and music - all which is loaded on my IPad 2 and ITunes on my computer. How do I do this most efficiently?
1. Do I use the same Apple ID# I use now on all devices, or set up a separate one on each device?
2. If I use the same Applie ID# on all devices, should I set up a different ICloud account on each device to keep the backups separate?
3. If I download an album on my IPhone, will either (or both) 1 and 2 allow that album to be downloaded on all of my devices through ICloud?
I was advised that if I have a large music library to make sure the phones aren't set to autosync. Does this sound correct?
I'm trying to get answers to my questions lined up before they I receive them so I know how to best set them up.
Thanks everyone.

1) You can use one id. My wife and I do.
2) Not sure. Sorry. We share one.
3) Yes.
We sync via the cable. We simply select what we want to sync on each device and sync.

How to get counter values from pci 6221 card?

Hii
I am using PCI 6221 card .. In that i am using the ctr o .. In my application i am using Linear encoder to measure the Lift movement.. so from software how to access the counter values i.e how much mm it moves...

Measure Angular Position.vi in the LabVIEW examples will be a good starting point. Adapt it to Linear Encoder by clicking on the selector below DAQmx Create Channel.vi.
You can also create a corresponding DAQmx Global Channel (or task) in MAX and then use it in your code.
Feel free to post back if you need further help.
Message Edité par JB le 10-31-2008 02:15 PM

My wife has purchased an iphone 6. She has a different id. How do we set it up to share info on icloud with our ipad and my iphone. use icloud on devises with different ids

My wife has purchased an iphone 6. She has a different ID. How do we set it up so that she can share photographs, contacts and calender on my iphone, imac and ipad.

You might see if this addresses any of your concerns ...
Family Sharing
... and here is another discussion thread on it ...
How to share icalendars, and contacts across users with iphones

How do you set up a different ipad on same computer with different itunes library

I am trying to update a clients ipad (who does not have access to internet at his residence) on my personal computer. When I open up itunes with his apple ID, I continue to get my itunes library information. I don't want to mix my information with his information. How do you set up a different i pad/itunes on the same computer? What I need to do is update the version of his i pad as his i pad is version 4.2.1. Thank you

Create a new Windows user account on the computer.
(86398)

How can I set my Mac to only share SPECIFIC folders with Win7

It used to work, but, even though I have set only my Public folder and a specific photographs folder to share with a Win7 PC on my home network, the Win7 machine can see the entire Mac HD.
I followed instructions from here:
http://www.trickyways.com/2011/07/file-sharing-mac-os-x-lion-and-pc-windows-7/
But if I type Run then enter the ip address of the Mac, all the folders appear. Is there a way to limit them to only the two specific folders?
I've mapped the single folder to a drive, so admittedly, unless you go into "Run", you can't see the other Mac folders and drives, but I'd still like to make sure it can't be done.
Thanks

Welcome to the Apple Community.
Cricket66 wrote:
........ How can I set photo stream to only upload specific images?
That's not possible unfortunately.

How do I set up a PCI-DNET card as master with A-B DNI as slave?

Similar Messages

Maybe you are looking for