How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

Similar Messages

Extending a wireless signal with an Airport Extreme Base Station, and an Airport Express as the "repeater".

I understand that I can extend Airport Extreme wirless "reach" with an Airport Express, but how? I've read through the posts and they say to "connect" the Airport Express. What does that mean, to an outlet, to an ethernet cable, what?

I understand that I can extend Airport Extreme wirless "reach" with an Airport Express, but how?
Enable the option on the AirPort Extreme to "Allow this network to be extended"
Then configure the AirPort Express to "Extend a wireless network"
If you do it this way, the AirPort Express connects to the AirPort Extreme using wireless only.
If you have the ability to run an Ethernet cable from the AirPort Extreme to the AirPort Express and leave it connected permanently, that will provide better performance than the "wireless only" type of connection.

I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

Which version of the AirPort Utility are you using?

Problems Setting up my wireless network with an Xb...

Hi, I have had some problems setting up my wireless networking.
I have everything switched on and am able to go online with the laptop and the Xbox with no problems but when I try to share media with the xbox I have problems.
I have opened the ports specified in the setup from xbox on windows firewall and have no problem connection Via Ethernet cable but when using wireless the xbox cannot detect the laptop.
I have checked the network map and both xbox and laptop are connected and have enabled sharing and am running sharing software.
Below is the network map.
I have also been having problems with BT software, the free virus protection will not install, The desktop help will not launch although it shows up on task manager and the installation disk does not launch correctly it doesn't get past the loading screen.
I have had a printer on the wireless network and had no problems printing.
If anyone knows how to resolve this please help.

I have this same Motorola modem and I just verified that my 802.11n AirPort Express Base Station (AXn) can get Internet access with this modem without any issues.
When changing ISPs (or networking equipment) it's always a good idea to start from "scratch" in configuring your equipment.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Power-up the modem; wait at least 10-15 minutes.
Power-up the base station; wait at least 5-10 minutes.
Power-up your computer(s).
In this basic configuration, computers connected to the base station, either by wire or wireless (as appropriate for the base station type), should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options.

My internet works fine with my wired cable modem, but when i connect to my extreme base station and setup my wireless network the internet no longer works and my apple tv by default

my cable modem works fine, but when I hook it up to my extreme base station and run through the prompts and set up my wireless network it doesnt work and neither does my apple tv by default. I am unsure how to correct this problem. It will come up saying that I dont have an IP address when I have it set to DCHP so I dont know what the problem is.

Push the reset button on the modem and power the modem off
Power off everything else....all devices....order is not important
Wait 15-20 minutes or longer
Connect the Ethernet cable from the modem to the WAN port (circle of dots icon) on the AirPort Extreme
Power up the modem and let it run for 5 minutes by itself
Power up the AirPort Extreme and let it run for 5 minutes
Power up each other device one at a time a few minutes apart
Check the network

HOW do I get my Extreme base station and Express to join a Linksys network?

OK... so I have FINALLY enabled my SLINGBOX to view remotely by totally removing my Airport Extreme & Express from the network look. I was told they are both routers and I have to pick one. The Linksys network works fine for all networking purposes... what it WON'T DO is connect my USB printer or stream iTunes to remote speakers. NOW, I have been told by using the Extreme & Express in "client mode" I can do this.
Basically HOW do I get my Extreme base station and Express to join the exsiting Linksys network?

Sorry but the AirPort Extreme base station (AEBS) does NOT have a client mode.
The AirPort Express (AX) does have a client mode. The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.

Bridging network with AP Extreme base station and AP Express

OK, here's the deal. I have an Airport Extreme Base Station on a WPA2 Personal network. Works great except that I want to boost the signal to the rest of the house. So, I bought an Airport Express. Airport Utility picks up both devices; but when I select the new Express to configure it, I get a msg asking to confirm that I want to switch networks. Well, I don't. I want to expand the network I have. Last night I did click "yes" and it was a disaster as I lost the Extreme altogether and the Express couldn't pick up a signal because - obviously - it wasn't connected to the ethernet cable as the base station, and also because (I think) the base station is configured to hide my SSID. I ended up working backwards and got the Extreme back to normal and put the Express back in its box until someone can tell me how to do this. I know Apple says it's easy; but it's a challenge for me. HELP!

A few things:
1. Please don't configure your base station to "hide its SSID". Doing this is absolutely useless as a security method. It will on the other hand complicate setup of your network, as well as the diagnosis of problems when they arise.
2. You must allow the Airport Utility to switch networks during the process. What is happening is that the Airport Utility must temporarily switch your Mac's wireless network connection from your existing base station to the wireless network created by your unconfigured Airport Express in order to communicate with and configure that Airport Express. After the Airport Express configuration is complete - if your Mac doesn't automatically switch your Mac's wireless network connection back again then just do so manually from the MacOS Airport menu.
3. To get a better understanding of what you are doing, start reading at page 42 of Apple's manual "Designing Airport Networks" found at:
http://manuals.info.apple.com/en/DesigningAirPort_Networks_Using_AirPortUtility.pdf

I have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

i have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it

Read the user guide:
http://support.apple.com/manuals/#airport

How can I set up a wireless network between two Mac Mini's (media centres)?

I've just received my second mac mini (core duo, 1.83, 1 Gb ram)and want to set up a wireless network to link this with my original mac mini (PPC 1.42, 512MB) and my Belkin wireless router (g std).
I'm using both as media centres in different rooms and want to keep all my media (films, photo's, music etc.) on one mini (connected to a 640GB external drive) and access it over the wireless network. Sort of a more felxible Apple TV setup??
I've got the wireless network working no problems with both mini's connected to the internet over the network but I'm stuck at how I get the two mini's to see each other. I've tried "the Missing Manual" and these forums but no success so far.
I know it can be done but would really appreciate any suggestions/directions on what to do?
Thanks in advance<<br>
MacMini PPC and MacMini Core Duo Mac OS X (10.4.9)

Jona11-
Greetings and welcome to the Apple boards.
This document should be very helpful.
Luck-
-DaddyPaycheck

How do I set up a wireless network at home??

Hi,
I am new to Mac's. I want to set up a wireless network at home, but I have not got a clue about AirPort, what it is or what it does!?! I am getting a new Mac, but my wife is currently using a Dell Windows laptop and our daughter is using a Windows PC. How do I set up a wireless broadband network at home which works with my Mac and my familys PC's? What do I need to buy and what do I need to do with them? I already have a broadband connection at home. Currently, my wife's PC is connected directly to the broadband modem (via an ethernet cable) that was supplied by the brodband company when I signed up to broadband.
Thanks for all your help with this.

scooter has provided links to Apple's pages for the AirPort Express and AirPort Extreme base station (AEBS).
Both of these devices are IEEE 802.11g wireless routers (also called base stations). If you have an Ethernet connection to the Internet (for example DSL or cable modem), you can connect either of these devices directly to that connection and create a wireless network. Since Ethernet and IEEE 802.11g are worldwide standards you can connect any compatible device (including PCs running Windows).
Every computer needs a unique IP address. You can think of an IP address as a street address for your house. A unique address guarantees that items addressed to you get to you.
Typically ISPs provide users with a single (one) public IP address. A public IP address is visible to anyone on the Internet. A router uses the single IP address provided by the ISP and creates multiple local (non-public) IP addresses for you computers. This allows you to use multiple computers.
If you need to connect both wireless and Ethernet computers you will need the AEBS. The AEBS provides a separate LAN port for Ethernet computers.
BTW, you can accomplish the same thing with any inexpensive wireless router.
The advantage of the AEBS over other routers is (a) built-in 56k modem for connecting to a dial-up ISP and (b) USB port for a single compatible printer.
The advantage of the AirPort Express over other routers is (a) sound output port for streaming music to a stereo and (b) USB port for a single compatible printer.

I have set up my wireless network and now have moved. How can I set up a new network with a different ip address

I have set up my wireless network on airport express and worked great. I have now moved and have a new internet provider and need to change my ip address. How do I do this

Is your new ISP providing you with a static Public IP address? ... or are they providing you with a dynamic IP address via DHCP (this would be the most common method for consumer-grade Internet service.) Next, which version of the AirPort Utility are you using? Finally, which version of the AirPort Express do you have?

Setting up a wireless network with windows XP PC

I may be getting a mac computer later this year & would like to know how to set up a wireless network between the mac & a windows XP PC. The PC has a DSL modem attached to it with a yellow line going from modem to PC & another Grey line going from the modem to the back of a phone in our kitchen. Our house is fairly big, it is one story but the rooms are sprawled out with a lot of clutter. I would like to have reliable internet access on my mac, & if it is a macbook pro I would like to be able to get to the internet throughout the house. The most important thing is stable reliable internet access as I am taking online classes. I would probably take the macbook pro into a bedroom or other adjacent room. The bedroom is further away, through 2 or 3 walls. The Adjacent rooms is one wall way.
I know this seems very basic, but I need a lot of help with this as I have never used a mac before (have been a windows user) & have never used more than just the one PC in the house, let alone a wireless network.
my mother along with I are both taking online classes, so sometimes there is competition for the the 1 computer & with my graphic design degree a mac has been recommended to me. So we are finding it would be easier to have more than one computer in the house so we can access our classes anytime.
So anyone, can this be done without breaking the bank?

I'm guessing that Modem was provided by your Internet Service Provider ?
They are the best people to talk to about upgrading that Modem to a Wireless one.
Usually if you're running a modem and phone from the same DSL line there's a small splitter box that plugs into the phone socket and then one wire connects your modem and another your phone. Picture below - if you do have one of these then post back and we can give better advice on a wireless modem to replace your current one.

Advice on how i can set up an office network with 40 computers.

I am planning on setting up an office network with 40 computers. What do you think is the best way i can do this? Thank you in advance.

Your first step should be to call an IT professional who has experience with this type of thing. He will need to survey the entire area and ask you dozens of questions about how you want things to operate. Then, he will present you with a proposal for the network listing all of the things that the system can and and cannot do.
Your second step would be to call another IT professional who has experience with this type of thing and go through the same procedure.
Your third step would be the same as the first and second.
Your fourth step would be to check the references provided in the steps 1-3 and then decide on which professional that you want to use.

How can i use an airport base station and multiple airport expresses with U-verse and still use wireless tv boxes?

I just got uverse, and when I put my Airport Base Station in Bridge mode I lose access to the 4 airport express stations I have. Can anyone tell me how to turn off the u-verse wireless, set up a network with all the apple stations and still have wireless u-verse tv boxes work? Thanks!

Can I relocate the airport base station to downstairs and connect it to the Sawtooth there for receiving wireless from the Verizon router and broadcast further to its wireless network?
Sorry but no the AirPort Extreme base station (AEBS) will not wirelessly connect to the network provided by the Verizon FiOS router.
What you could do is get another AEBS, an AX, or a Time Capsule and place that downstairs. Then use that device to wirelessly connect to the wireless network provided by your current AEBS. If your current AEBS is not 802.11n capable then you would need to use WDS to make this happen. One bad thing about WDS is that each WDS link cuts your affective wireless bandwidth in half.

Problem consistently printing via new (summer 2011) AIRPORT EXTREME BASE STATION and Brother wireless printer (model HL5370DW). What am I doing wrong?

Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
My theories:
- true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
- The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
QUESTIONS:
- Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
- I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
Rule out:
- wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
Any help will be greatly appreciated.
Thanks in advance!

13 ASCII characters = 104 (aka 128)-bit WEP
encryption
If turning off WEP works, then you just need to
provide the cameras with the "Equivalent Network Password".
One of the problems with WEP is that the actual
standard relies on a 10 character HEX key for 40bit
WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier, vendors use certain
algorithms to convert simple alphanumeric passwords
(or passphrases) into HEX keys, thus enabling the use
of simple easy to remember WEP password rather than
lengthy HEX keys. The problem is that different
vendors use different algorithms to generate the HEX
key and therefore a ASCII password on an AEBS will be
hashed differently on a non-Apple client and vice
versa.
You may find the following article helpful:
- Apple article, especially the part about
"Third-party client to Airport".
Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
Thanks again for your help and suggestions... I really appreciate it.
geoff

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

Similar Messages

Maybe you are looking for