How do I set up an Airport Extreme Base Station ("Snow") for use as fax (on

I'm on a PowerMac G4 Digital Audio version without a built-in modem. I already have a Linksys wireless network set up between my Mac and PC laptop. So... I don't want to use the wireless networking on the Airport...
I just want to configure the Airport Base Station to use the built in 56K modem so that I can fax directly off the Mac. I did that on my old computer that had a built in modem, but I need to know how to configure this G4 and Base Station modem to perform this task.
Please help me connect the right wires (does the G4 connect to the base station with USB?). Then the power cord, and an RJ11 line from the phone to the airport base...
And what software (the used airport I bought doesn't have a software disc).
Thanks for any help!

Saxparilla, Welcome to the discussion area!
Sorry but the modem inside the AirPort base station (ABS) has NO ability to FAX at all.

Similar Messages

How can I set up the airport extreme base station with windows computer

how can I set up the airport extreme base station with windows computer

Hi - you need Airport Utility version 5.6.1 for Windows 7 - go to http://support.apple.com/kb/HT1547 to download it to your computer - the setup depends on what kind of modem you have and if you have another router connected - post back with this info to proceed - thanks

HT4259 How do I set up an Airport Extreme Base Station (v. 7.6.1) to allow wireless network extension?

I have an Airport Extreme Base station (purchased in 2009) and an Airport Express base station (purchased in 2011 - the model that plugs directly into the electrical outlet) (both version 7.6.1 according to the Airport Utility info). I want to use the Airport Express to extend my wireless network. Using Airport utility setup I have a software option on the Airport Express to set it up to extend the network but I do not have an option on the Airport Extreme wireless setup screen that I can check to allow my wireless network to be extended.
All of the documentation I can find on Apple Support states that I should have an option I can check to allow the wireless network to be extended while in the wireles setup section for the Airport Extreme in Airport Utility; but, that check option isn't there. Is this a case of my Airport Extreme base station being too old to offer that option? Incidentally, when I try to select the extend wireless network option on the Airport Express from the Airport Utility wireless setup menu I get an error message (no details - just an error message). The same Airport Express sets up fine if I select join a network (not what I want to do). Am I just dealing with outdated equipment or does anyone have a suggestion? Thanks.

Close AirPort Utility if it is open.
Temporarily, move the Express to the same general area as your AirPort Extreme and power it up and wait a minute.
Hold in the reset button on the Express for 9-10 seconds and then release. Give the Express a full minute to restart to a slow, blinking amber light.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear
Click on AirPort Express just below that and AirPort Utility will automatically open
Wait a minute while AirPort Utility analyzes the network and announces that the Express will be configured to "Extend" the AirPort Extreme network.
Enter a device name for the AirPort Express and click Next
Wait another minute to allow the configuration to occur.
When you see the Setup Complete message, click Done.
Now move the Express to a location that is approximately half the distance from the AirPort Extreme and the general area that needs more wireless coverage
Power up the Express and you are all set. Trash those old instructions.

How to add NAS to existing Airport Extreme Base Station Network...

Hi! I have a Airport Express network (DSL provided via a DSL modem) that is connected to the PC via ethernet, iMac 333 via Wireless adapter, and Powerbook via wireless card. I am bursting at the seams with components!!
I have the printer set up via the AE.
I would like to add a NAS to the works. (Just to see if it can frustrate me even more! )
How exactly would I hook this up? Any suggestions? Has anyone done this? Have a favorite NAS device you can recommend? We are looking to install this for a centralized place to store all our music, photos, movies, etc. We have TONS of digital media to store and it is clogging up our respective hard drives!
Thanks in advance for the help!!
Minder
Ti Powerbook 15 inch Mac OS X (10.4.6) iMac Grape 333MHz, Custom built PC and a Flower Power iMac soon coming home with me too...
Ti Powerbook 15 inch Mac OS X (10.4.6) iMac Grape 333MHz also

It is unclear... Do you have an AirPort Extreme base station (AEBS) or AirPort Express (AX)?
If you have an AEBS then you should have this configuration:
DSL modem<->[WAN] AEBS [LAN]<->PC
If that is your current setup, you would need to modify it by adding an Ethernet switch (or hub) so that it looks like this:
DSL modem<->[WAN] AEBS [LAN]<->switch<-+->PC
.......................................|->NAS

Cannot see Airport Extreme Base Station--Watch for 2.4Ghz traffic!

(Issue is addressed in the body of this post)
Great when working on 802.11n at 5Ghz, BUT...
If you have to be compatible with 802b/g you are forced to transmit at 2.4Ghz. Traffic at this frequency can be so bad that it made my station invisible (even with "Interface Robustness" activated). The "automatic channel selector" is supposed to choose a clutter free channel for clear communications, but it does not work well. I had to reprogram the station (through ethernet) to manually change the channel to a more stable one. In my case, channel 8 did the job.
After this, the Airport base worked perfectly!
I live in a condo area where I get 8 strong wireless networks, all at the same time. Add microwave ovens, TV's and cordless phones and you get a jammed 2.4Ghz highway. Make sure to select a channel that provides seagway to the "carpooling lane".

Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
Any help would be greatly appreciated.

AirPort Extreme Base Station error? Using Macbook Pro

I am new to all of this and I thought I would be capable enough to set this all up but apparently I am not. HELP! I am trying to create and set up a wireless network using my Airport. I have an AT&T Westell Modem that is using dial up for internet. When I connect the modem directly to my computer I have internet access. The lights on the modem indicate that the ethernet and all other capabilities are working. I plugged in my Airport Extreme after using a cable to connect the modem to the Airport using the Ethernet port. The amber light is flashing and I followed the instructions to setting up my Airport using Airport Utility from the Applications folder. It detects my correct Airport but when I go to update and create my wireless network this error pops up:
Make sure your Apple wireless device is plugged in and in range of your computer or connected via Ethernet and try again. (-6737)
My computer is sitting right next to the modem and the Airport. I am not near any metal or any water, and there are no walls or other electronics to interfere. Am I missing something here? Restarting all devices has also proven unsuccessful...Thanks for anything that can help!

If you just bought it I would recommend calling Apple, they can help you set it up.
Also you should consider getting a high speed Internet connection. They are very inexpensive these days and would make your Internet experience much more enjoyable. Where you live I would think you have a choice of DSL (available from most telephone companies) or Cable, which would be the quickest but also more money too.
Regards,
Roger

Airport utility no longer recognizes my Airport Extreme Base Station, which had been set up to extend a wifi network

Hi. In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds. Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended. I folllowed all the directions from the apple support pages, and finally got it to work. I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension. Then a week or so ago I noticed that my laptop would no longer connect to my base station. I did not have time to look into it until this week. Airport utility, either on my Mac or iphone no longer recognizes my base station. My mac is running OS X 10.10.1 and my iPhone is running iOS 8.1.2 I have tried both hard, soft and factory resets of my base station to no avail. The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before. I can't actually connect to it, but it does try. Then after approximately 5 minutes, it disappears from my list.
Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c? airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software. I am attaching an image of that.
Thank you,
John
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?

I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature.

Airport Extreme Base Station Internet Connection issue

I have a connection question for Airport Extreme Base Station.
I have Comcast cable broadband. I connect that to a Linksys router for
use with my Vonage phone, and then from the Linksys router I connect
via Ethernet to my iMac. I like the direct Ethernet connection for
performance reasons.
In order to set up a home network to connect my Tivo's (and eventually
my PC and printer), I have set up an Airport Extreme Base station and
connected it to the Linksys router from it's ethernet connection to the
WAN (cable modem) input on the Extreme.
I have connected to the Airport network with my iMac, but since I am
connected to the Internet via Ethernet, I cannot tell if my Airport is
connected to the Internet so that I can use it for my Tivo. My PC is
still in storage from a move, so I can't check with that.
My question: How can I tell if my Airport is connected to the Internet
without disabling my Ethernet connection on my iMac?
A few more info points/questions in case it helps answer:
1) I previously used this Airport to connect this iMac wirelessly.
2) Should I be connecting it to the LAN port since it's coming out of
the router?
3) If the connection issue is because I am going through the Linksys
first, can I connect the modem to the airport and then use the LAN port
to connect to the Linksys router?
4) If I have to disable the ethernet connection to test the Airport,
how do I do it? Just unplug it?
I appreciate any help as the online and manual help from Apple is not
quite up to par with such a complex configuration.
Regards
Bill

2) Should I be connecting it to the LAN port since it's coming out of
the router?
No, connecting to the WAN port is fine.
3) If the connection issue is because I am going through the Linksys
first, can I connect the modem to the airport and then use the LAN port
to connect to the Linksys router?
The issue is that you have two routers which effectively creates two networks. Unless this was your original intent, you will want to setup the AEBS as a bridge.
To set up the AirPort Extreme Base Station (AEBS) as a bridge, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, make these settings:
Network tab
- Distribute IP addresses (unchecked)
- Apply the new settings.
- Wait at least 5 minutes.
4) If I have to disable the ethernet connection to test the Airport,
how do I do it? Just unplug it?
Well, that's certainly one way, but an easier way is to temporarily disable the "Built-in Ethernet" in your network configuration.
System Preferences > Network > Show > Network Port Configurations
- Built-in Ethernet (unchecked)

Airport Extreme Base Station Installation OS X v.10.3.4?

I currently have a Classic iMac with OS X v.10.3.4. I want to use it to set up new Airport Extreme Base Station. According to the information on Apple’s website, setup and administration requires OS X v, 10.4 or higher. Will the installation work with v. 10.3.4? If not, what will? Thanks

It looks like you'll have to find somone with a 10.4 install to set it up.
I've yet to find an Apple APP that said it needed a certain version of the OS to run, that actually didn't require that or higher.

Using the WAN port as a "LAN" port on the Airport Extreme Base Station...

Hi everyone,
I'm re-building my home wireless network and I'm doing so in preparation for the Slingbox AV I ordered last week. Here's my current setup:
I have a DSL modem attached to an Airport Express (802.11n) in my office broadcasting my internet signal. I have an Airport Extreme Base Station (802.11g) set up in my living room as a WDS extender. I currently use the base station in my living room to connect the DishNetwork ViP722 DVR to the internet and allow me to set recordings remotely on my iPhone when I'm away from home. I use the LAN port on the base station to do this, and now with the Slingbox on the way (should be here early next week), I'm wondering what I need to do to make an internet connection available for the Slingbox AV.
My question: Will I be able to simply use the WAN port as a "LAN" port since the Airport Extreme Base Station is being used as a WDS? It'd be awesome if the WAN port would become, essentially, a LAN port since it isn't being used.
Thanks in advance for your advice and insight!

slugoo wrote:
My question: Will I be able to simply use the WAN port as a "LAN" port since the Airport Extreme Base Station is being used as a WDS? It'd be awesome if the WAN port would become, essentially, a LAN port since it isn't being used.
I'd be surprised if that worked. The operation of an AirPort base station depends on keeping the WAN port and the LAN port(s) separate, as those normally are on two different networks.
You might consider buying an Ethernet hub or switch, which would allow your AirPort Extreme's LAN port to be shared. Here's an example of an inexpensive one:
http://www.bestbuy.com/site/olspage.jsp?skuId=7169244&st=ethernet+switch&type=pr oduct&id=1110266457435

Printing wirelessly to MacBook Pro with Airport Extreme Base Station

I have an Airport Extreme Base Station that I used to use wirelessly until I got Verizon Fios. The Fios technicians said the base station couldn't be used and so it's been sitting unused for a few months. However, I really, really miss printing wirelessly, and was wondering if it was possible to use the Airport Extreme Base Station ONLY to print wirelessly, and not connect it any way to my internet (I don't want to mess with any of the fios stuff at all).
If it's not possible, is there any other way to print wirelessly without purchasing another product or special printer. I have a HP c4480 printer.
Thanks!

If your printer has a USB cable the easy way to go about this in my opinion is to plug that USB cable into your Extreme base station. I have the Extreme ABS that looks like a flying saucer. I plug the usb cable into the port that has the symbol that doe NOT look like this <--> rather it looks like a Saguaro cactus.
My computer then sends print documents to the Extreme via WiFi and then Extreme sends them to the printer via the USB cable.
If your Airport status is not showing in the Mac's menubar go to system Prefs/Network/Airport and check a little box so it will show up in the menu bar.
Now if your Extreme is plugged in the wall and powered up your Mac should be able to find it. Click on that menubar item for Airport and scroll down and select your Airport Extreme. I don't know for sure what its name will be. It should still be the same as it used to be when you used it last.
Now try printing a simple document. In the print dialog window you should be able to select what printer you want to use. If your new Extreme printer is listed select it. You may need to click on Print & Fax and figure out how to select it from there, and choose it to be the new default printer.
I think this info will do the job. Whenever you want to print you have to go to the Airport icon in the menubar and change your airport connection from your Verizon stuff to your Extreme. Then of course you have to change back when you are done. That is why it would be great to toss the Verizon WiFi radio out the window and just plug your Verizon modem into your Extreme WiFi radio transceiver (router). But I understand you cannot deal with that at this time.
If this does not do the job, if I have missed something, I will bet you 5 bucks that you can still figure it out if you just look at any error messages and/or look at the Print&Fax prefs and the Print dialog windows etc. and see what I may have missed. Maybe you have to go to SystemPrefs/Sharing and allow your printer to be shared. I don't think so. The way I figure any of this stuff out is to just look at stuff and think and try things and see what happens.
Your Verizon setup should be something like this.... a cable comes into your house and goes to a 'modem'. From there and ethernet cable (CAT-5 cable) goes from that modem to your Verizon router (WiFi radio transceiver).
As for getting rid of the Verizon router, when you are ready to give it a go, simply unplug the ethernet cable (it has a plug on the end that looks like the kind of plug that telephones use to plug into the wall, except it is a bit wider, but still has that same kind of snap-lock tab) that comes from the Verizon modem (the modem has the heavy round cable and probably many blinking lights) and plug it into the Extreme. Mine has an icon on the Extreme that is many dots in a circular pattern.
At this point you may have to unplug the Verizon modem form the wall AC power and the Extreme also. Then plug them back in, wait a minute, go to your Airport icon on your Mac menubar, Select Extreme and start surfing the web.
It really is that simple with a Mac. Maybe Verizon has found a way to make things difficult but my guess is no. Any password should be taken care of in your Airport Setup Utility program. It should be the same password(s) as you used before when you used your Extreme.

I need help with connecting an external HD to Airport Extreme base station

So i have the base station set up, and it recognizes my hard drive in the airport utilities and have the file sharing turned on, but when i connect to the base station wirelessly from my macbook pro, the hard drive and base station does not show up in the shared section in my finder. Any ideas as to whats up?

I'm having a similar problem, and I hope you'll excuse my ignorance but is there a difference between rebooting and just restarting. I've done the latter (numerous times) but not the former.
I have set up my Airport Extreme Base Station to my wireless router (DSL Internet connection) and to an external hard drive (MyBook Essential 640GB with USB connection). Internet works fine.
When I plug the hard drive directly into my MacBook it recognizes it fine, I can copy files to it, add folders, explore them etc.
When I plug the hard drive into the Base station, it appears as a network drive on the side bar of my finder window, but when I click on it to open it, it is empty, it shows 0 items and the available memory, but none of the files I put on it are visible to explore.

DNS settings for Airport Extreme Base Station

This month's MacWorld suggests that changing the DNS setting of the wireless device might increase the speed of the connection. What setting should my Airport Extreme Base Station use.
The Computer system says 10.0.1.1 and it works. When I entered the numbers they suggested I get no connection.
Any suggestions?

To change DNS setup on the Airport you need to put in the DNS change on the Internet tab. The Airport will always place itself as the main DNS server to the network clients that connect by DHCP, unless you set the Airport to static IP.. and it will use your ISP DNS server by default.. you can change them if you want. Just type in the new DNS you want to use.
This month's MacWorld suggests that changing the DNS setting of the wireless device might increase the speed of the connection.
http://www.macworld.com/article/2824564/slow-internet-edit-your-dns-settings.htm l
In most cases this is really so minimal as to be insignificant. The airport should cache the regularly used DNS addresses and you can test it by ping to your local DNS or the DNS recommended by MacWorld??.. but honestly a few ms is not going to change the world. To the clients the local network addressing should be still using the Airport as the main DNS.. you can setup manually in each device a different DNS but that can give local network issues as it then has to find local clients by broadcast.
I have a complex dns setup for other reasons.. getting past geolocks..
If I ping my local ISP dns I get
ping 202.76.170.228
PING 202.76.170.228 (202.76.170.228): 56 data bytes
64 bytes from 202.76.170.228: icmp_seq=0 ttl=61 time=25.422 ms
64 bytes from 202.76.170.228: icmp_seq=1 ttl=61 time=25.984 ms
64 bytes from 202.76.170.228: icmp_seq=2 ttl=61 time=25.504 ms
64 bytes from 202.76.170.228: icmp_seq=3 ttl=61 time=24.933 ms
64 bytes from 202.76.170.228: icmp_seq=4 ttl=61 time=25.297 ms
64 bytes from 202.76.170.228: icmp_seq=5 ttl=61 time=25.258 ms
64 bytes from 202.76.170.228: icmp_seq=6 ttl=61 time=24.915 ms
If I ping google DNS. 8.8.8.8
ping 8.8.8.8
PING 8.8.8.8 (8.8.8.8): 56 data bytes
64 bytes from 8.8.8.8: icmp_seq=0 ttl=57 time=37.985 ms
64 bytes from 8.8.8.8: icmp_seq=1 ttl=57 time=37.562 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=57 time=37.715 ms
64 bytes from 8.8.8.8: icmp_seq=3 ttl=57 time=37.639 ms
64 bytes from 8.8.8.8: icmp_seq=4 ttl=57 time=36.845 ms
If I ping the US DNS server.
ping 208.122.23.22
PING 208.122.23.22 (208.122.23.22): 56 data bytes
64 bytes from 208.122.23.22: icmp_seq=0 ttl=51 time=187.209 ms
64 bytes from 208.122.23.22: icmp_seq=1 ttl=51 time=187.398 ms
64 bytes from 208.122.23.22: icmp_seq=2 ttl=51 time=186.681 ms
64 bytes from 208.122.23.22: icmp_seq=3 ttl=51 time=187.030 ms
64 bytes from 208.122.23.22: icmp_seq=4 ttl=51 time=186.731 ms
64 bytes from 208.122.23.22: icmp_seq=5 ttl=51 time=186.967 ms
It is very obvious the best ping is the ISP dns because the route path is shorter..
Google is very good but still takes longer and of course dns in another country is much worse.

Software to install Airport Extreme Base Station

Hi all,
Any idea how I'd re-install the Airport Extreme Base Station? I lost the disk that came with it.
Thanks for your help,
Chelsea

chelsea_marti, Welcome to the discussion area!
There is no need to re-install anything. The "AirPort Admin Utility" and "AirPort Setup Assistant" are in the /Applications/Utilities folder on your Mac.

Airport Extreme Base Station and G4

I have a G4 Desktop running OS 10.2.8 and a G4 laptop running 10.2.4 wth an Airport Card. I have high-speed internet access through a Wi-Fi ISP. I attempted to set up the AIrport Extreme base station, running the cable from the WiFi Antenna through the base station and connecting the base station to my desktop trough the ethernet port. When I attempted to run Airport set up, it could not find an airport card in the desktop, so this went no where. I was not able to access the internet through the base station, I expect because I had not set up the airport system. I was left with only dial up internet service and a significantly slower operating system. I gave up and reconnected directly to WiFi.
For what it is worth, the center light of the base station was on and the light to right was blinking through out this time. Any assistance is welcome.

Ok, please try the following, in order. After each step, try powering-down and restarting the Mac to verify if the steps solved the problem. If it hasn't continue on to the next step in the sequence:
1. Run the Disk Utility to repair Disk Permissions.
2. Turn off the Mac OS X Firewall
o System Preferences > Sharing > Firewall
o Click the "Stop" button.
3. Move System Configuration Files
(Note: You will have to reestablish your network connections settings.)
o Go to /Library/Preferences
o Move the SystemConfiguration folder and com.apple.networkConfig.plist file to the desktop.
o Restart your Mac. (Note: OS X will rebuild the files that are now sitting on your desktop. If this doesn't resolve the issue, you can move the folder & .plist file back to it's original location.)
4. Create a New User Account
o Create a new user account.
o System Preferences > Accounts > Click "+" to add a new account
o Log off, then log back on with the new user account.
o Try connecting with the AirPort.

How do I set up an Airport Extreme Base Station ("Snow") for use as fax (on

Similar Messages

Maybe you are looking for