How do I set up LabView RealTime ETS on a desktop computer?
I have been trying to set up the LabVIEW Real-Time 8.0 OS on a desktop computer. I have read the the "Requirements for a Desktop PC as a LabVIEW Real-Time target and followed the instruction in the installation manual "Using Desktop PCs as RT Targets with the LabVIEW Real-Time Module".
The problem I have run into is that there is a built in Network card on the motherboard (Intel Pentium 4 processor ) and the boot program is unable to recognize the Intel Pro/100S Network card I have added (PCI slot 1). The error message is: "Unable to configure primary network device". I can not figure out what settings I have to change in the BIOS to get the thing working (BIOS version EV91510A.86A.0444)
I have done the following:
- Formatted the drive as FAT32 & used the Desktop PC Format Harddrive Disk
- Set the Serial Harddrive ATA/IDE Configuration to legacy
- Disabled Legacy USB Support
- Disabled onboard & legacy FP Audio
any help would be appreciated
I have tried turing off the built in NIC from the BIOS setup but I could not get it to work. I disabled the Onboard LAN but this did not seem to do anything. I am not sure what I have to change in the BIOS setup in order to make the PCI network card the primary network device.
Similar Messages
-
I have a new iPod touch; I have an iTunes library of music for an older iPod shuffle. I'd like to set up the iPod touch for my wife with a separate library of music - I was successful in setting up a separte account, but it seems my 800 songs are still there in the library. How do a set up a new account on the same computer without bringing along all the music that will clog up her iPod touch?
There's a few ways of doing it. The following document may be of some help:
How to use multiple iPods, iPads, or iPhones with one computer -
I have a new computer with Windows 7, Outlook and I use iTunes with an Apple iPhone 4 and a iPad. My devices have iOS5. How do you set up iTunes 10.5 on a new computer and sync these devices. I have already downloaded iTunes 10.5 on my computer. Also, I use MobileMe. Thanks for your help. LCP
Thank you for your response. I have all of my files, etc. and am sitting here on the old computer. I just wasn't sure if I should simply save the iTunes program I am using or insall a new version.
After I get iTunes onto my new computer do I authorize the new computer before I plug in my IPod or after?
I'm sorry I didn't point out that I had all of my files available. For some reason, working with iTunes and my iPod make me nervous.
Thanks again.
Rustyglo -
Hard drive crashed, how do I set up itunes sync from iphone with new computer?
hard drive crashed, how do I set up itunes sync from iphone with new computer?
hard drive crashed, how do I set up itunes sync from iphone with new computer?
-
Hardware for LabVIEW Realtime (ETS)
Hello NG,
right now we are using two NI-Devices (PCI 5122 and PCI 6251) in an
Intel based PC with Windows XP as the operating system.
We would like to switch to a Realtime-System (ETS) using our PCI-devices
again in an Intel based PC. As I read (and as we also had to realise)the
hardware requirements are quite strict and it is very hard to figure out
if some hardware will work in advance.
So, does anyone have experience with setting up a realtime system (ETS)
on a standard PC? Moreover, can anybody give some advice which hardware
(manufacturer and product-id) will work?
Thanks in advance
OliverActually I read all of those documents. First we tried to set up a
realtime system using RTX (realtime extension for windows), trying to
get our hardware to work in a realtime environment on top of windows.
It was really hard to get at least something to work, where something
means running labview without hardware on one of the several PCs we
tested. But we didn't get access to any of our NI-devices, where at
least the 6251 should have worked referring to the specs.
So, after calling the NI support they suggested using ETS on a separate
machine instead of using RTX. We then downloaded the programm to check
several PC for ETS capability. But all we tried got stuck somewhere in
the testing procedure (they are probably too new and maybe ETS is not a
friend of AMD )
So now, we are going to buy a PC for ETS, but after what we experienced
with RTX and also with ETS so far, we feel that it could be hard to get
the right PC or PC components. Because of this I'm looking for advice
regarding hardware (manufacturer, partnumber etc.). -
Hi there,
I have a LabJack U12 interface card that has two analogue outputs, AO0 and AO1. What I would like to be able to do is set up LabVIEW V6.1 to eventually control the dimming of some external lights, from say a simple control on LabVIEW's front panel.
I will have some external circuitry connected to the interface card to perform the dimming of the lights, so all I will require is a variable voltage on the output of the card. I think the specification of the card is 0 to +5 volts for the two analogue outputs. I have tried looking on the website for LabJack (www.labjack.com) for any ideas, but with no success! Please find my LabVIEW file as an attachment.
I would be very grateful for any help on this matter,
Neil Sampson.
Attachments:
Basic_ver6_2_1.vi 158 KBOn the labjack downloads page:
http://www.labjack.com/downloads.html
Pick "Labview5 VIs" download. In the zip file is ljacku50.llb, which contains EAnalogout.vi for outputting an analog signal.
2006 Ultimate LabVIEW G-eek. -
how do I set up my Imac to allow using both my computer speakers and a Bose SoundLink system as outputs at the same time. I can use one or the other, but not both. From systems Preferences I must select one or the other. I want both to work all the time.
Hi,
I would recommend you to use 0FI_AP_4 rather using both, particularly for many reasons -
1. DS: 0FI_AP_4 replaces DataSource 0FI_AP_3 and still uses the same extraction structure. For more details refer to the OSS note 410797.
2. You can run the 0FI_AP_4 independent of any other FI datasources like 0FI_AR_4 and 0FI_GL_4 or even 0FI_GL_14. For more details refer to the OSS note: 551044.
3. Map the 0FI_AP_4 to DSO: 0FIAP_O03 (or create a Z one as per your requirement).
4. Load the same to a InfoCube (0FIAP_C03).
Hope this helps.
Thanks.
Nazeer -
I have the newest version of i-tunes and cannot for the life of me figure out how to set up home sharing to authorize a new computer! Everything I find on the subject is for older versions of i-tunes. PLEASE HELP. Thanks
Ok I found it. Alt S to get the top navigation menu!
-
HT201317 How do i set up 2 photo streams on the same computer
How Do I Set up 2 Photo Streams with 2 deffernt iphones on my pc Computer?
http://www.microsoft.com/windowsxp/using/setup/winxp/accounts.mspx
-
What is the correct way to set up your email accounts in your desktop computer?
In an effort to resolve all sorts of strange behavior taking place with my email, I've been looking into the settings for icloud and Mail, the app. Is there a difference between the "mail, contacts &calendars" settings in system preferences of your desktop computer and the actual account settings in Mail, the app?
More specifically, do I only enter my individual email accounts in the account settings for Mail, and only the icloud settings for my me account in the system preferences section?
I hope I'm making sense because I need help desperately.
Thanks in advanceTo answer the OP's original question.
Both the System Preferences -> Mail, Contacts and Calendars AND the Mail.app -> Accounts route both take you to the system preferences pane.
Just so you can confirm it, try both methods to get to the accounts list, and at the top left of the particular window you'll see 'Show All' which takes you back to System Prefs.
I think it's just apples way of getting everyone to the right place i.e. those who are use to using system prefs and those who are used to setting up accounts in their mail apps
That's good old apple and their user friendly interfaces for you -
How can i download movies from my laptop to my desktop computer
I have movies on my itunes on both my laptop and desktop computer and both are under my itunes account but how can i share the movies between the two? i haven't been able to figure it out and whenever i check for "available downloads" it says all downloads have been downloaded for this account, so if anyone can't help that'd be great
Or just connect the laptop and mac with a 'Ethernet LAN cable', that's the quickest way to transfer lots of data.
-
LabVIEW does not support command line arguments. Are there some modifications to the Execution Display.vi that would enable this behavior?
Hi,
This mods is to the LabVIEW OI supplied with TS2.0.1 and labVIEW 6.1
In the TestStand - Runtime Operator Interface.vi, the cmdline is obtained and the full path to the sequence file is stored in a global variable. When the Sequence Display is launched and the case First Time is executed. The cmd line global is checked for an empty string, if its not then the string is concatated with the string 'Open Sequence File - No Prompt|' and put on the message queue. This will result in the sequence file being opened.
The cmd line parsing is pretty basic. the argument is nothing or the full pathname to the sequence file.
If this is what you are after then send your email to [email protected]
I tried to attach the vi's but I am having some problems with thi
s. Probably a size restriction.
Hope this helps.
Ray Farmer
Regards
Ray Farmer -
How do I set up separate user accounts on the same computer
I would like to set up a separate user account on the same computer with different bookmarks and favorites. Can it be done? How do you do it?
Thanks, Bobbyhttp://www.microsoft.com/windowsxp/using/setup/winxp/accounts.mspx
-
How can you set up to sync 2 ipods on one computer
I have 2 ipods and want to set them up on 1 computer how do I do that?
Set up each individually. If desired, click here and pick one of the options.
(58432) -
How do i set up a second ipod touch on my computer?
I have an I tunes account, which I set up for my son, I have now purchased an I pod for my daughter and wish to use both on the same computer.
I have created an account on the computer for my daughter, but, i am struggling to fathem how to keep the data seperate on both devices.The new I podd has sync'd to the other account and now the music from the first I pod is on there??
I want to keep them seperate, so i dont delete things from either by mistake??
I have opened a new user within i tunes, but that is where I have hit the brick wall....How to use multiple iPods, iPads, or iPhones with one computer
What is the best way to manage multiple...: Apple Support Communities
Maybe you are looking for
-
Problem in Accession inner join with [Microsoft][SQLServer 2000 Driver
Hi Can you tell me what can be cause my sql statement is correct gives result but if i used below statement in my JSP ,cause error 1) ps1=connection.prepareStatement("select RQM_IN_RQSTN_ID_PK,RQD_IN_ITM_ID_FKPK,RQD_VC_ITM_DSCRPTN,RQD_IN_STTS_ID_FK,C
-
How do I sync Iphone contacts without iTunes
My mom has an iPhone 3gs and I am trying to help her with apps. I tried to download an app for her, but it says "This iPhone requires the iphone 3.2 update". I tried to update the iphone on her computer, but her computer is all messed up and I can't
-
I'm trying to retrieve contacts from iCloud on my new samsung but it says that there is no back up data in my account
-
Setting the current LOV values in a form
I have report with an edit button that allows the record to be edited in a form , both of which are on the same page (a report + form - created with the wizard). I have a field "Status" which is a select list in the form. So when I click on the 'Edit
-
Diff between Business service and Business System?
HI Experts, Pls let me know wht is the difference between business service and business system?? when we will have to go for business service and when for business system?? thnx in advance.. New XI