How do i set up time capsule to work with airport extreme base to extend wireless network?

i have a airport extreme base, how do i set up a time machine to extend the wireless network i have with airport extreme? i have also 3 airport express's connected to the same network to extend my wifi all over my house. thanks in advance.

Much better graphics, thanks.
You can leave the Time Capsule connected by Ethernet from the Linksys and configure for a "roaming" network as mentioned previously.
To do this, open AirPort Utility - Manual Setup
Click the Wireless tab below the icons
Wireless Mode = Create a wireless network
Wireless Network Name = Same name as the AirPort Extreme
No check mark needed next to Allow this network to be extended
Radio Mode = Same setting as the AirPort Extreme
Channel = Automatic
Wireless Security = Same setting as the AirPort Extreme
Wireless Password = Same password as the AirPort Extreme
Confirm Password
Click the Internet icon, then the Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Update to save settings and allow the Time Capsue to restart
Then power down the entire network
Wait a minute or two
Start the modem first and let it run a full minute
Start the AirPort Extreme the same way
Power up the switch
Power up the Time Capsule for a minute
Keep starting devices one at a time about a minute apart
Now, your computer will automatically pick up a wireless signal from either the AirPort Extreme or Time Capsule, whichever device is closer and providing the stronger signal.

Similar Messages

Time Capsule 4th Gen with 2 AE's to extend wireless has no consistent connection

I have a Time Capsule 4th Gen & 2 Airport Express (A1264) devices used for extending the wireless range - all on v7.6.4. The network setup is a u-verse modem that goes to a Cisco 8 port router, that has one ethernet line to the Time Capsule, one ethernet line goes to one of the AE's, another ethernet line to another 5 port router and an AE connected to it, and the remaining ethernet lines are to hardwire different rooms in the house.
The goal is to have the most robust wireless network I can create for the house that has, 4 iphones, 5 ipad's, 4 mac's, 2 pc's and a few other wirelesss devices. I also have an AT&T wireless Microcell (not sure if relevant). The issue revolves mostly around really poor wireless performance on iphones and iPad's they just take foreever to load pages and in many cases I need to do things like turn off wireless, forget the network, restart, airplane mode and such to get it connected. I've tried multiple configurations, and the performance is not consistent.
My understanding is that the AE's connected to ethernet on the home network can extend the TC's range and make the movement of mobile wireless devices throughout the house seemless. Is this setup doable or am I just not going to get this with the current configs.
TC setup, DHCP to u-verse gateway, Network Mode set to Create... ., WPA2 Personal, 2.4 channel 9, off bridge mode, timed access control enabled
AE1 setup, DHCP to u-verse gateway, Network Mode set to Create... ., WPA2 Personal, 2.4 channel 5, off bridge mode, timed access control enabled
AE2 setup, DHCP to u-verse gateway, Network Mode set to Create... ., WPA2 Personal, 2.4 channel 7, off bridge mode, timed access control enabled
Really appreciate any advice or tips on improving this setup. Thanks!

My understanding is that the AE's connected to ethernet on the home network can extend the TC's range and make the movement of mobile wireless devices throughout the house seemless.
This is generally true if you are using Mac laptops, but PCs and mobile devices using the iOS systems like the iPhone and iPad will not usually automatically "switch" from one wireless access point to another as the device moves from one area to another.
That's a nature of the beast of the iOS system, I am afraid.
Usually, if you move the iOS device from one area to another, you willl need to turn off the WiFi on the device, then turn it back it on. Then, it will usually pick up the stronger signal from the closest wireless access point.
Sometimes, if I move an iPhone or iPad from one area to another in a multiple access point network, the iOS device will switch over to the stronger signal after a few minutes.
I haven't installed iOS 7 yet, so can't comment on whether it might be better in this regard, but I would be surprised if it was.

Setting up Time Capsule to Work With Verizon DSL

I am not able to establish a new network using the Time Capsule I just purchased. The funny thing is that the capsule is replacing an Airport Express that works just fine. Same cables, same location, just that the time capsule cannot get an appropriate IP address from the DSL modem. Anyone have any experience in setting up the unit (using Airport Utility) to connect with Verizon?

I realise that, because it's 802.11g the MacBook will not be able to achieve the potential connection speed of the 'N' Time Capsule, however, even if I had the TC, with a G4 PowerBook on the LAN everything would connect at the (lower) 11g speed anyhow, wouldn't it?
As you have already ascertained, any 802.11g device connected to a 802.11n network will only operate at the highest available bandwidth that 802.11g allows ... mainly 54 Mbps. In addition, when even a single 802.11g device connects to a 802.11n network, 802.11n clients will only get about 70% of 802.11n's top bandwidth. To get around this, you can configure a "dual band" network. With this type of network, you can run both "g" and "n" clients on separate network to get the highest bandwidth possible for each. So, in your case, the Time Capsule will run a "n" only network and your AX will provide the "g" only one. The AX would be connected directly to the TC by Ethernet and reconfigured as a bridge so clients on either network would "see" each other.

How do I set up Time Machine to work with an Iomega network hard drive?

I have just bought a new iMac having switched from Windows, and am very much a beginner when it comes to all things Apple. Previously I had used my NAS hard drive with my old windows pc. i successfully used it to transfer a lot of data from the old pc to the iMac but can't seem to get it recognised when I try to configure time machine. I have downloaded the latest version of Iomega Home storage manager which appears in the application folder in the dock, but when I click on The HSM icon it just disappears and nothing happens. I can access the drive through the Bonjour service and can see its contents in Finder. I have looked through the forums here but much of the info assumes a level of knowledge that i don't have. Is there an 'idiot's guide' anywhere to enable me to set up time machine to use the network hard drive?

You would probably benefit from a couple of things, first going through these 2 links
Time Machine FAQs & Time Machine Troubleshooting.
If you still have questions there is a TM forum, because TM is part of OS X you will find the forum in the Snow Leopard forum. Click Apple Support Communities and in the search field type Snow Leopard. Once you are in the correct forum you can narrow your search by clicking Refine this list.
Roger

Can't set up a printer to work with airport extreme...

Alright, I've been stuck here for a while.
I have an HP PCS 1310. I can set it up perfectly using a USB cable, but when i try to set it up via Airport Extreme, i can't.
When i try to set it up through airport, the computer doesn't know what drivers to use. It can find the printer, and it'll tell me the name, and the location, but it will ask me to choose what drivers to use. I can't find my printer on the list. I don't really know what to do.
I'm sorry for being so vague...I wish i could post some pictures (and if i can, can someone please explain how?)
Thanks everyone!!

Here is what fixed the printing issues for me:
1) Open up the Airport Utility and determine the IP address of your Airport.
2) Add the printer via System Prefs -> Printers (using Boujour)
3) Then, navigate to http://localhost:631. This will take you to the CUPS setting for the printers.
4) Go to "Manage Printers" on the CUPS setting for your printer.
5) Click on "Modify Printer." It will prompt you for your username and password for the computer (enter your short name that you use to login to your machine and password).
6) Click continue until you get to Device. Change this to AppSocket/HP JetDirect. Click continue.
7) Change to: socket://your_ip:9101
8) Continue on till you get to the end of the Modify Device section.
9) Open up Preferences -> Printers and print a test page.
If this doesn't work, try changing the port to 9102 instead of 9101.

How do i set my time capsule up to function as an external hard drive

How do i set my time capsule up to function as an external hard drive? Is this even possible? I had a friend tell me it woudl be a good set up to get a time capsule with my Macbook Air to use as a gigantic external hard drive but then was unbale to wlak me through the setup after I bought the equipment. Any suggestions?

It depends on what you already have equipment wise..
Just bridge the TC..
I cannot walk you through it either if you use v6 airport utility.. due to my refusing to run Lion until it gets network issues sorted.
Download and run the real utility http://support.apple.com/kb/DL1482
Go to manual setup..
Internet tab
Connection sharing.. select off bridge mode in the drop down box.
You can then if you like turn off wireless under airport wireless.. The TC is now a plain network client with hard disk.
Personally I would keep the wireless on but sort the channels manually if you already have a wireless AP or router.

How can I set my time capsule to back-up only once a day?

How can I set my time capsule to only back-up once a day. It appears to be backing up several times a day. Not sure there is a set schedule for the back-ups and they take a great deal of time; over an hour each.

tdenny2 wrote:
Not sure there is a set schedule for the back-ups and they take a great deal of time; over an hour each.
Then something is wrong. Changing the schedule will only deal with the symptom (and give up one of the better features of Time Machine's usually quick and unobtrusive hourly backups).
See if the size of the backups makes sense, considering what you've changed since the previous one. If it seems much too large, that may be the problem. See #D4 in Time Machine - Troubleshooting for some common culprits and ways to see just what's going on.
If the sizes seem reasonable, see #D2 in the same link for things that can cause extra-slow backups.

When I switch my time capsule to 5.0ghz mode the range of my wireless network drops significantly. Near the Time Capsule my Macbook Pro works fine, in my bedroom I have almost no signal. In mixed mode it works fine. Any ideas on how to get 5.0 working?

When I switch my time capsule to 5.0ghz mode the range of my wireless network drops significantly. Near the Time Capsule my Macbook Pro works fine, in my bedroom I have almost no signal. In mixed mode it works fine both placed. Any ideas on how to get 5.0 working? I thought 5.0Ghz was supposed to have a wider range. Do I need to change a setting on the Macbook Pro?
Thanks, W

I'm not sure if you understand that 5 GHz has some upsides, but also some very significant downsides.
The upside is that the 5 GHz signal will allow faster speeds.
The downside is that you must always give up something in order to gain something else.Unfortunately, the marketing hype about 5 GHz does not go into very many details about this.
In the case of 5 GHz, the 5 GHz signals are much weaker than 2.4 GHz signals, so they do not travel as far or penetrate any obstructions like walls or ceilings nearly as well as 2.4 GHz signals. In many cases, in order to get good 5 Ghz performance, you literally have to have almost a line-of-sight relationship between your computer and the wireless router.
If you have a new dual band router, which broadcasts both a 2.4 GHz and 5 GHz signal simutaneously, your Mac will connect to the best signal quality automatically depending on its location in relation to the router. In the same room, without any obstructions, it will connec to 5 GHz. But, take the laptop down the hall a few rooms and around the corner and the Mac will connect to the 2.4 GHz signal because at that location, the 2.4 GHz signal is not only stronger, it is also faster.

HT1178 I have set up Time Capsule to use with Time Machine. When I open Time Machine it 'cannot find' the Time Capsule and I have the Select the Disk each time. In the Next Backup tab it always says "When disk is connected" even though the disk is alrea

I have set up Time Capsule to use with Time Machine but when I open Time Machine it 'cannot find' the Time Capsule and I have to 'Select the Disk' each time. In the Next Backup tab it always says "When disk is connected" even though the disk is already connected.

Your pro doesn't matter.. I presume it is happily working.
Your imac setup has got messed up because you changed from a local (my book being USB type I presume) to network drive. Did you do a clean install of Lion?
Did you use the backup from the Pro on the imac? Otherwise I don't see how the Pro shows up in use previous disk. Where is Pondini when you need him??
You cannot download Time Machine as an App and replace the current version. It is built into the OS.. the only way to do it is a clean install. Unfortunately that might be the only way around the issue.
There is a number of issues that Pondini has covered in the setup issues of troubleshooting.
This is the most relevant I think. http://pondini.org/TM/B6.html
But look at the whole section B setup problems.
http://pondini.org/TM/Troubleshooting.html
If it was me, I would store all the info you need.. not using TM but using a straight copy of files.
Then clean install Lion. I doubt any of these issues would exist if you had not installed Lion over existing setup or used a different backup.
See if you can get Pondini to respond.. !!

I just upgraded from my 2008 MacBook to a new Macbook Pro. How do I get my time capsule to work on my new MacBook? I did data migration, but the time capsule did not pick it up. Any ideas?

I just upgraded from my 2008 MacBook to a new Macbook Pro. How do I get my time capsule to work on my new MacBook? I did data migration, but the time capsule did not pick it up. Any ideas?

If you migrated all the info from time machine to your new MBP. The TM will usually ask to connect to the old backups.. sorry I am not sure is this what you want to do.. Personally I think you start a fresh backup.
BTW Time Capsule does not do anything.. it is a dumb hard disk in a box.. it is TM that does everything.
Look at B5 and B6 here about connecting to your backup.
http://pondini.org/TM/Troubleshooting.html

How do I connect a 1 T time capsule to a new airport extreme so I can use it with time machine?

How do I connect a 1 T time capsule to a new airport extreme so I can use it with time machine?

Bridge the TC.. plug it into the AEBS with ethernet.

Can i set up my Time Capsule 1st generation with airport 5.5.3?

can i set up my Time Capsule 1st generation with airport 5.5.3?

Yes, if you are asking about AirPort Utility 5.5.3 for Windows.....and you are running XP SP3 on your PC.
AirPort Utility 5.5.3 for Windows
If you are running XP SP2 on the PC, then you will need to use AirPort Utility 5.4.2 for Windows
AirPort Utility 5.4.2 for Windows

I want to replace a four year old Time Capsule for a new Airport Extreme, how difficult is it?

I want to replace a four year old Time Capsule for a new Airport Extreme, how difficult is it? The ADSL connection come from a Modern Router provide by the local Telephone company.

Reply back when you get the new device, but in short, you'll have to put your extreme in bridge mode and just connect the same wires as your current TC.
See here http://www.macobserver.com/tmo/answers/how-to-add-a-time-capsule-or-airport-extr eme-to-an-existing-network-with-br

Time capsule not recognized by airport extreme - first time setup challenge

Air port utility not recognizing time capsule. We have airport extreme and time capsule (recent purchase to back up 2 wireless mac laptops and the G5 which is connected to the modem). Modem is conected to airport extreme and I connected the Time capsule via ethernet as I thought the speed would be 1GB and faster than wireless "n." Somehow now the airport extreme does not recognize the time capsule. In the network utility, airport is not listed, only ethernet and firewire. What steps should I take to enable time capsule to back up the laptops wirelessly as well as the G5 (non-wireless.) Thanks!

I would hold the reset button on the back of the Time Capsule for 5-10 seconds and I would wait to connect it to the AirPort Extreme to see if you can set it up. If you can access the Time Capsule with AirPort Utility then I would plug it into the AirPort Extreme and continue your setup.

What is the best way to get a time capsule to work with a new network name?

What is the best way to get a time capsule to work with a new network name?

Well it seems that you did not explain to us the full story. Did you change ISP's or something? Why would it not show up anymore?
What colour is the light on the time-capsule? If it's blinking amber, then you probably need to do a factory-reset. That should get it to show up again in AirPort Utility.

How do i set up time capsule to work with airport extreme base to extend wireless network?

Similar Messages

Maybe you are looking for