How do I set up timed access control for a time past midnight

I would like to set up timed access control for a number of my devices that would stretch past midnight...   An open network from 6AM to 2AM - effectively only blocking access from 2AM tp 6AM in the morning....
Any notion on how to do this?  the timed factily does not like the setting to enable 6A to 2A, says the times are invalid. 
Setting up timed access from 6AM to 11:59P, then doing another from 12A to 2A causes a service "hiccup" of 1 Minute.

Set up each device as follows:
Everyday........Between.......6:00 AM and 11:59 PM
Add a second rule for each device that will state....
Everyday.....Between.......12:00 AM and 2:00 AM
You might think that there would be a one minute break between 11:59 PM and 12:00 AM, but that will not be the case, at least on every AirPort that I have ever programmed..  Reason.....11:59 is really 11:59:59:59 turning off at 12:00 AM.  But, you have a second rule to allow access at 12:00 AM, so the AirPort will be "on" at the same time the first rule ends, so there will be no break.
If you really want the second rule to turn the AirPort "off" at 2:00 AM.......then set that time for 1:59 AM. If you set the rule for 2:00 AM, then AirPort will really turn off at 2:01 AM.

Similar Messages

  • How do I set up different hardware controls for different patches in mainstage?

    I'm using Mainstage 3.0.4 and a Novation Impulse.
    I created a concert, with the drawbar organ as my first and most important patch. I assigned the hardware controls on the Novation exactly how I wanted them, with the sliders controlling the drawbars, and the rotary controls changing the distortion, reverb, etc. It was perfect. I was happy.
    Then I added a new instrument (a new patch, not a new channel or anything like that), a Wurlitzer. Once again I assigned my hardware controllers as I wanted them, and was happy with that.
    When I saved the concert, and went back to my organ patch, my settings didn't stay the same, but they still work for the Wurli.
    My question is this - do I have to have a new concert for each instrument patch I want to use, if I need to assign different controllers for each patch? This would be stupid! If not, what I am doing wrong, that I can only set up one set of hardware controls per concert, instead of per patch?
    Thank you in advance for the help!!!

    Hi
    matthewabennett wrote:
    CCTM, thank you! I have a small idea what you mean, but I still can't implement it :-)
    You have some fundamental choices:
    A) If you want to see Drawbar Controls for organ Patches, and then have other types ( knobs/sliders etc) for other Patches, you could simply make all the screen controls you need, then assign and map them as required.
    B) you could simply use drawbar screen controls only and remap them to other parameters for non-organ patches
    C) You could use Smart Controls ( which will update their appearance in a 'smart' way
    D) You could make your own Drawbar type controls using standard faders
    The basic process in a 2 part thing:
    Assign incoming MIDI messages from your controller to Screen Controls in Layout mode. This is global for concert. Per patch ( or Set or globally for the Concert) you then map the Screen Controls to parameters for each patch as needed.
    Smart Control MIDI assignment is done in the Assignments and Mappings pane
    CCT

  • Airport Utility Timed Access Control does not allow/restrict access to wireless clients per the time set.

    I have been trying to setup Timed Access Control in Airport Utility and it does not seem to be working correctly. 
    In Airport Utility from Edit Timed Access Control I Enter a name for my device (iPad/iPhone any device), enter my mac address, set time for Everyday and use default Between 9:00 AM and 5:00 PM, save and then update. When I go to my device iPad iPhone etc. I still have access even when it is after the time set, 5:00PM.  If I set no access it will restrict access also I set a time between 2:00 PM and 5:00 PM and access was restricted.  It doesnt seem to matter what the device is.  I know that the MAC Adress is set correctly.  It seems like an issue with the Utility, possibly time miss match or something.  Not sure if I am missing something or if this Utility just has flaws. Please Help.

    I changed the default to (no access) and set an entry for my test device (an iPad) to "Everyday Between 9am to 5pm.  The iPad was still able to gain access to the network. 
    Something else to note, if I try to edit the time of an entry it gives me an error on my MBP "Invalid value", "The value for “Timed Access Control” is invalid."  This happens even if I delete a digit (number or letter in the time field) and replace with the exact same. Not sure if the two are related. I have tried to edit access from my iPad.  I don't get any errors but I still don't get the expected results.  I called Apple to try and get Tech support but they were not much help. Thanks again.

  • In JSF, how to make a menu with access control?

    In JSF, how to make a menu with access control?
    The access control can be guided by programming, database or other means if possible?
    Thanks

    I want to make a dvd menu in iMovie because i don't have IDVD and can't find anywhere to download it?
    For making DVDs I would recommend iMovie 06 and iDVD 09 both readily available on Amazon or eBay.  Shop for iLife 06 and iLife 09.
    You can make menus and chapters with any version of iMovie except the latest one. There's nothing wrong with iMovie 11 either but I prefer iMovie 06.
    By using iMovie 06 and iDVD 09 I make DVDs with professional moving menus with very little effort. They look almost as good as Hollywood.

  • I turned off Internet access, using airport timed access control.  Now, I can't turn it back on.  The base station can't be found.  Please help.

    I turned off Internet access, using airport timed access control.  Now, I can't turn it back on.  The base station can't be found.  Please help.

    Can you take a look at this one and offer your opinion please?
    https://discussions.apple.com/message/21889032#21889032

  • How can I have different access control for the guest network (different than the main network)?

    I am trying to control my main wireless network with access control via mac id with no password. I wanted a separate guest network with password access and no access control. However, the only way that the guest network works is if I specify unlimited access as the default. Is what I am trying to do possible.

    I am trying to control my main wireless network with access control via mac id with no password.
    Definitely not a recommended method for security. MAC addresses are easily cloned by anyone who wants to do so with free tools available on the Internet. An unwanted guest will be on your network in less than a minute if they want to be.
    Strongly recommend that you use WPA2 Personal security with a non-dictionary password to protect your network.
    I wanted a separate guest network with password access and no access control. However, the only way that the guest network works is if I specify unlimited access as the default. Is what I am trying to do possible.
    Unfortunately, Apple does not allow separate Access Control for the "main" and "guest" networks. It's all or nothing, I am afraid.
    Likely, the  "best" way to set up Access Control is change the default rule to No Access, Then you will need to enter in the details for every device that you want to allow to connect for both the "main" and "guest" networks with the time limits for each device.

  • Can i set up an access password for the ipod on my ipad 2?

    I purchased an Ipad 2 for my son to use in his therapy for autism. He knows how to use it and knows that we have purchased shows and movies for him to watch in the car. Well now that is all he wants to do. I am wondering if there is a way that I can set up a password to access the ipod. If he cant get into the ipod to see shows and movies he will be fine with just playing the games we have for his therapy. I have looked online and have not had much luck finding an answer to this question. So again can someone please tell me if there is a way to set up an access password for the ipod on the ipad2??????

    Have you got Home Sharing set up (http://support.apple.com/kb/HT3819) ? i.e. he may be viewing the content from your computer, not on the actual iPad. If that is the case (which would explain to me him being able to access the videos via the iPod app), then the Restrictions settings that I've already mentioned should also work on that 'remote' content.
    Edit : your last reply appeared whilst I was typing/checking this. And no, the Videos/iPod apps can't be passcode protected, you will need to go back into Restrictions and remove the restriction, or if the films are only on your computer and not on the iPad itself you could turn off home sharing on the iPad whilst he's playing the games : Settings > iPod and tap on your account id and/or password on the right under Home Sharing and delete it/ them (re-enter them when you want to re-enable it).
    Message was edited by: King_Penguin

  • Access control for different user groups in APEX 4.0

    Hi guys,
    in Apex 4.0, is there any way to use the access control page to configure access control for different user groups?
    The access control page currently only has an access control list by users with 3 privileges namely, Administrator, Edit & View where Administrator has the highest access level & View the lowest. Therefore 1 user cannot have more than 1 different privilege, however if the user belongs to 2 or more different groups then we can control what access he can have in a more fine grained manner. We also want to have more than the 3 privileges given.
    Can we assign different groups to different users and let them have different privileges to be configured by page, region, process or item level?
    Now Apex will create 2 tables, Apex_Access_Control & Apex_Access_Setup to store the application access control mode & access control list. It will also create 3 authorization schemes "access control - administrator", "access control - edit" & "access control - view" based on the 2 tables.
    Does this mean we have to change the table structures & edit the authorization schemes to suit our usage? We are reluctant to do this because if we upgrade to a newer version of Apex then we would have to merge our pl/sql coding with Apex's updated code.
    How can we auto-configure more than the 3 authorization schemes in the access control page? Is there any way to achieve a finer grain of access control based on the current access control administration page given by Apex without writing it ourselves?
    We are afraid that we may have missed something on Apex access control & do not want to reinvent the wheel.

    Hi Errol,
    to build your own application authorization scheme around the security model supplied by Apex for administration of the Apex environment would be a bad idea.
    This was never intended for authorization scheme management in custom built Apex applications, it was solely intended to control access in the Apex environment overall. The API for it is not published, and making changes to it, such as adding more roles, would run the risk of breaking the overall Apex security model. It would not be supported by Oracle and Oracle would not guarantee the upwards compatibility of any changes you make in future versions of Apex.
    In short, you should follow Tyson's advice and build your own structure. As he indicated, there are plenty of examples around and provided your requirements are not too complicated, it will be relatively simple.
    Regards
    Andre

  • How do I set up an itunes account for a minor?

    How do I set up an itunes account for a minor?

    Hello kyleaho0048,
    Thanks for using Apple Support Communities.
    If you are trying to set up a new Apple ID, please follow the instructions in the following article:
    iTunes: How to set up an Apple ID within iTunes
    http://support.apple.com/kb/HT2731
    Since this is for your young son, I also recommend taking a look a the the built-in parental controls in iTunes:
    iTunes: Using Parental Controls
    http://support.apple.com/kb/ht1904
    Take care,
    Alex H.

  • How do I set up a seperate account for my wife?

    We finally purchased a nice new iPhone for my wife. But she would like her own iTunes account. How do I set up a seperate account for her? She has her own laptop, with an iTunes account on it that I was using. Should I just un-install that iTunes package and have her download a new version? I'd rather have two versions so I don't lose the music on that old iTunes account. It's not huge, but would be a PITA.

    Apple ID
    Go to iTunes > Store > Sign Out (your apple id) and sign your wife apple id in.

  • How do I set Firefox to be usable for all users on one computer?

    How do I set Firefox to be usable for all users on one computer?

    I would think the about:config entries discussed are ex-factory set to values each user has to change individually, after the installation has run its course. The solution could be to have patched files ready to install post factum:
    [https://developer.mozilla.org/en-US/docs/Mozilla/Preferences/A_brief_guide_to_Mozilla_preferences A Brief Guide to Mozilla Preferences - MDN]

  • How do i set up a second display for my iMac desktop?  I want to use both displays at the same time.

    how do i set up a second display for my iMac desktop?  I want to use both displays at the same time.  My iMac is the 24" Late 2006 model.  I recall that there is a cord for plugging in a second monitor, but I want to make sure that i can use both monitors side-by-side at the same time.  thank you.

    If the Display supports DVI, then you will need a > Mini-DVI to DVI Adapter and a DVI cable.
    If the Display only supports VGA, then you wiil need a > Mini DVI to VGA Adapter and a VGA cable.
    Noting that the (digital) DVI is far better than the (analog) VGA connection.
    Also see > Using Dual Displays on Mac OS X: The Experience

  • How can i set up multiple user accounts for my new ipad mini?

    How can i set up multiple user accounts for my new ipad mini?

    The iPad mini is basically a one user device. There are no Accounts. You can set up restrictions so that only you can do certain things.

  • How do I set up OpenDNS to work with my Time Capsule running 7.7.3 in Bridge Mode?

    How do I set up OpenDNS to work with my Time Capsule running 7.7.3 in Bridge Mode?

    Set up your "main" router to use the OpenDNS servers, and the Time Capsule will automatically pick up those settings. No configuration is needed on the Time Capsule.

  • How do I set the default welcome page for PUBLIC user

    gurus,
    i'm using -
    Oracle 9i Database
    Oracle 9ias Portal Release 2
    QUESTION => how do I set the default welcome page for the PUBLIC user.
    i did the following to achieve this -
    1. logged into portal
    2. clicked on builder
    3. clicked on administer tab
    4. selected PUBLIC user in the Portal User Profile portlet
    5. went to the preferences tab
    6. in the default home page selected a custom page group
    7. logged out of portal
    8. open a new browsere session
    9. type the portal URL and i get the login page ....??
    i'm unable to understand this behavior ... shouldn't i be getting the page group that i set for the PUBLIC user in step 6 above ....
    the second QUESTION is => when the user logs out he/she should see the PUBLIC page set in step 6 above ... but, instead the user sees a page that is as follows -
    Partner Application Name Logout Status [Logout Status]
    Oracle Portal (portal) logout status
    The SSO Server (orasso) checkmark
    buzz.resva.trw.com:7778 checkmark
    infrastructure.happy.resva.trw.com checkmark
    portal1.buzz.resva.trw.com checkmark
    portal2.sylvester.resva.trw.com checkmark
    sylvester.resva.trw.com:7778 checkmark
    so, how can i set the default page for the PUBLIC user and also a page when he user logs out.
    ideas anyone ....?
    thanx a bunch.
    hero

    Hi,
    The sequence of operation you are doing to set the home page for public users is correct. You are getting the login screen as the "custom page group" selected as "home page" has not been granted to public.
    Also, while logging-out, it is normal behaviour to get the screen where it shows the list of partner applications from where user has been logged-out. When you click on "Return" button, you will get to the "home page" set above.
    Hope it clarifies the things.
    Regards,
    Ved

Maybe you are looking for