How do I setup Airport express with ethernet connection to my modem?

Hi there - hoping to get some helpg as I'm having challnges setting up my Airport express via ethernet cable connection directly to my router. It will setup wirelessly no problem, but I occasionally get dropouts when streaming music and I'm hoping to remedy that with a direct cable connection. I know I have to change some settings in my airport utility, but haven't had any luck getting it right.
Here is my setups if it helps:
Airport express, 1st generation, model A1264
Cisco router (provided by my intenet provider)
Macbook Air, running 10.8.5
Airport utility version 6.3.1
Thanks!
Phil

Unfortunately, you are getting incorrect advice here. Might be a good idea to start a new post, since the original thread is long out of date.
First, please confirm that you have a compatible Express with the AirPort Extreme. This would be either the current A1392 version.....or the previous A1264 version.
Next, we need to confirm "how' you want to extend, since you do not mention this in your post.
Are you planning to "extend" by connecting the AirPort Express to the AirPort Extreme using a permanent, wired Ethernet connection (highly recommended).....or.....are you trying to "extend" by having the Express try to connect wirelessly to the AirPort Extreme?

Similar Messages

How do I setup airport express to extend my airport extreme

How do I setup airport express to extend the airport extreme

Unfortunately, you are getting incorrect advice here. Might be a good idea to start a new post, since the original thread is long out of date.
First, please confirm that you have a compatible Express with the AirPort Extreme. This would be either the current A1392 version.....or the previous A1264 version.
Next, we need to confirm "how' you want to extend, since you do not mention this in your post.
Are you planning to "extend" by connecting the AirPort Express to the AirPort Extreme using a permanent, wired Ethernet connection (highly recommended).....or.....are you trying to "extend" by having the Express try to connect wirelessly to the AirPort Extreme?

How do I setup Airport Express to extend my CISCO router's wifi range?

Hi,
I am using CISCO EA4500 router for internet connection via wifi. I have Airport Express with me, which I want to use as extender of the wifi network. I setup the Airport Express as "Extend the wireless network", provided same base station name (CISCO), network name (JKS) and passwords.
However, I am not able to get it to work. Its gives me error saying network: unknown.
I have just 1 BHK flat, and even then the range is not enough to reach from my DR to BR. I tried using Airport Express as the base station as well. But the problem is again the range.
Help me please.
Jayesh

Can I do it other way around? I mean setup Airport as Base station and use Cisco to extend the wireless network?
I doubt that the Cisco router would be able to to wirelessly extend the AirPort network, since Apple uses proprietary settings that are designed to work with other Apple routers.
Also, when I am trying to use just Airport, I am not able to connect multiple devices at the same time
Sorry, but I don't know whether you have the AirPort connected to the Cisco router using an Ethernet cable....or.....whether you are saying that you have the AirPort connected directly to your modem using an Ethernet cable.
If the AirPort is connected directly to your modem.....what is the make and model number of this device?
Since you know that the Cisco router is working OK when you have it connected to your modem, things would be much simpler if you connect the AirPort to the Cisco router using an Ethernet cable. Can you do this?

Trying to set up Airport Express with Ethernet Powerline adapters

Hello,
Having some problems trying to set up my Airport Express with Netgear ethernet powerline adapters.
I want to set up as follows:
Wireless Belkin router --- powerline <---> powerline --- airport express --- home stereo system
The problem I have is that I can connect the airport x in client mode & wirelessly play music using airtunes (until the sound breaks up) but itunes does not find the airport x when connected via the powerlines.
I have airport admin utility configured as follows:
Airport tab:
Wireless mode: create a wireless network
Wireless network name: same as my wireless router SSID
Allow this network to be extended: unticked
radio mode: 802.11n (802.11b/g compatible)
Channel: automatic
Wireless Security: WPA/WPA2 personal (as per my router)
Wireless Password: as per my router
Verify Password: as per my router
Internet tab:
Connect using: ethernet
Connection sharing: off (bridge mode)
Music tab:
Enable Air Tunes ticket
no password set
In iTunes, I have home sharing on & share entire library selected with no password set.
Using OS 10.6.5 & Airport Express 7.5.2
I can ping the IP address of the airport express when connected via the powerlines but cannot select the speakers in iTunes (they are greyed out).
Any assistance would be appreciated....
Thanks

Hi,
Thanks for the quick response...
As suggested, I connected up the Airport X to the Belkin and plugged in a pair of headphones. It didn't work, still could not select the Airport X as speakers.
Dug out my old Netgear DG834G and connected that up in place of the Belkin - it worked. Next connected in the Netgear powerlines and it still worked.
So, the problem is the relatively new Belkin F7D4401 router.
Looks like I will have to find an alternative 802.11n...
Thanks for your help.
Regards
Simon

Airport Express with ethernet?

Hi All
Can the AE increase my wireless coverage upstairs, whilst backhauling traffic via the ethernet link into my switch/router downstairs? I'd like the same wireless network upstairs/downstairs naturally.
I tried to 'extend' in the options, the log file shows it connects, then disconnects immediately despite all my details being correct (mac, ssid etc etc)
The switch/router/wireless device downstairs is a Dynalink device.
Thanks
Kris

Can the AE increase my wireless coverage upstairs, whilst backhauling traffic via the ethernet link into my switch/router downstairs?
Yes
I tried to 'extend' in the options, the log file shows it connects, then disconnects immediately despite all my details being correct (mac, ssid etc etc)
"Extend" is a setting that is only used if the AirPort Express (AX) is connecting to another Apple router using a wireless connection....not Ethernet.
Please follow these instructions:
Open AirPort Utility and click Manual Setup
Click the Wireless tab located just below the row of icons as adjust your settings to look like this:
Wireless Mode = Create a wireless network
Wireless Network Name = Same name or SSID as your main wireless network
No check mark is needed next to "Allow this network to be extended"
Radio Mode = 802.11n (802.11b/g compatible)
Channel = Automatic
Wireless Security = Exact same setting that your main wireless network is using
Wireless Password = Same password as your main wireless network
Confirm Password
Click the Internet icon
Click the Internet Connection tab and adjust your settings to look like this:
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Click Update to save the settings and allow 40-45 seconds for the AX to restart
Very Important......power down your entire network.....all devices......order is not important
Start the modem first and let it run 2-3 minutes by itself
Start your main router the same way
Start the AX the same way
Continue starting devices one at a time about a minute apart until the network is powered up again
Please report on your results

How to setup airport express with time machine

just bought airport express so i can extend my wifi range,can anybody help on how to set up! I have time machine 2gb, my house is wired with cat6 cable in all the bed rooms, but now only half my house get wifi,so i want to extend it.I know i have to go into air utility and change some stuff, but sure what stuff?

I assume that this is a new AirPort Express and you have not tried to configure it previously.
Locate the AirPort Express in the general area where you would like to have more wireless signal coverage.
Connect the Ethernet cable to the WAN "O" port on the back of the AirPort Express
Power up the AirPort Express and let it run a few minutes. The amber light will be blinking slowly at this point.
Click the AirPort icon at the top of your Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click directly on AirPort Express.
AirPort Setup will open up automatically on your Mac, take a minute to analyze the network, then announce that the AirPort Express will be configured to extend the Time Capsule network.
Enter a device name that you want to use for the AirPort Express and click Next
Wait a minute while AirPort Setup configures everything for you. When you see the indication of Setup Complete, click Done.
You should be all set.

Mac Min cannot see PC with either Airport Express on ethernet connections

I am trying to network a Mac Mini, G4 Power Book, a PC laptop and PC desktop so far I can get the Mini to see the G4 and PC laptop but not the PC desktop. I have an Airport express and all but the PC desktop work OK with it. The PC desktop can see the Airport, which I have called MitchBVI, but when I try and connect to it nothing happens. The wireless card in the PC is a Linksys WMP5G. I have not enabled security yet as I wanted to get the whole network operating first.
I have tried linking the Mini to the PC with an Ethernet cable and if I do that the PC can see the Mini but not the other way round.
The fact that the PC laptop and the Mini can see each other suggest to me I have the correct permissions set on the Mini. As the PC desktop can see the Airport Express I assume that the Linksys card is working OK. As the PC desktop can see the Mac when the Ethernet cable is connected it would seem whatever permissions are needed on the desktop are set correctly.
Any suggestions greatly appreciated.
Thanks
Mitch

Thanks I had found your site and changed the MSHOME and WORKGROUP to a diffferent name MITCH that is how I got it working in part. My Powerbook can see the Mac Mini and so can the PC. The former through a wireless connection the later by ethernet. I can ping the IP address of the PC from the mac mini but cannot make the connection.
For a while on the PC i actually had a wireless connection but could not access the net with it and it dropped out again. Maybe having an ethernet and wireless connection is the problemalthough with the wireless disabled that has not helped.
I had a spare Linksys card and tried replacing it but that did not help. As I said in my first post other PC laptop works fine.
Thanks

How can i setup airport express

i need to help to setup airport express

what after that how can i confugure it
Bob Timmons wrote:
OK, thanks.
We know that you have an AirPort Express model A1392
We also know that you have Windows 8.1
We do not know if you have installed AirPort Utility 5.6.1 for Windows - Apple Support. If not, you need to do this.
We still do not know what you want the AirPort Express to do. What service will it perform on your network?

Has anyone figured out how to print through Airport Express with Vista?

My wife has Vista on her laptop and everytime we try printing through the Airport Express/Bonjour it doesn't work. It might print one page and then stop, but never any further.
The latest Bonjour is installed.
Is there anything else?

Was this printer ever at one time connected to the Vista PC directly ? also with Vista ive seen issues with bonjour printers. Its due to either the firewall of this new junk they added in called windows defender. This application ive seen various results from it like it thought my install of Gears of War was a virus and etc. One thing you could even try doing is turn off the windows firewall and see if this resolves this issue. Seeing as this computer is behind a "hardware" firewall such as a router anyways you wouldnt really need to have the firewall on unless you had a strong need for the extra security

Apple Airport Express N Ethernet connected disappearing

Hello,
I have just setup my apple airport express to connect to my belkin wireless N router F5D8636-4 v2 via Ethernet. I have turned all the wireless features off on the express as I'm only using it to send music to my DAC. It is assigned I.P by DHCP all other computers are manually asigned I.Ps so no conflicts. My computer is also wired to the router and running windows 7 64bit. It all works great apart from when I turn my P.C off.
When I turn it back on it cannot find the airport express over LAN until I reset the apple airport express by powering it down and back on. Is this right? Surely not? OR when im finished with my hi-fi should I be turning the apple airport express off?
Anyone got any suggestions?
Cheers
Dan

The Express can effectively extend the 2-Wire network if 4 conditions are met during the configuration of the Express to create a wireless network:
1) Same wireless network name as the 2-Wire network
2) Same wireless network security as the 2-Wire network
3) Same password as the 2-Wire network
4) Bridge Mode Operation
Most users know 1) and 3), but 2) is the real key here. If the wireless security setting of the 2-Wire and Express do not match up exactly....then you will have 2 separate wireless networks instead of the seamless network that you desire.
So, the first question....do you know the exact type of security settings that the 2-Wire router is using? If not, it is not possible to configure the Express the way that you want without a long trial and error guesswork process.
You may need to contact your service provider to find out how to access the settings to learn what they are.
If you do know the exact security settings being used by the 2-Wire router, post back with that info and we can provide a step by step configuration guide if you want.
I assume that you are using OS X 10.6.8 as your profile indicates.

Apple Airport Express N Ethernet connection problems...

Hello,
I have just setup my apple airport express to connect to my belkin wireless N router F5D8636-4 v2 via Ethernet. I have turned all the wireless features off on the express as I'm only using it to send music to my DAC. It is assigned I.P by DHCP all other computers are manually asigned I.Ps so no conflicts. My computer is also wired to the router and running windows 7 64bit. It all works great apart from when I turn my P.C off.
When I turn it back on it cannot find the airport express over LAN until I reset the apple airport express by powering it down and back on. Is this right? Surely not? OR when im finished with my hi-fi should I be turning the apple airport express off?
Anyone got any suggestions?
Cheers
Dan

problem due to firewall settings - resolved

Airport Express sloooow ethernet connection

Using an Airport Express base station as a wireless access port on my ethernet network. Configured the out of the box AE using the set up assistant over wireles form my laptop. Got the DHCP IP assigned in the reange of the router and made the connection. Email works but slow. Mounting a Google search page took 90 sec! Configuration: Netgear router with 8 port switch and T1 down service. Four of the router ports serve 4 locations of a business network. Second tier switches serve the puters in the 4 locations. The AE is ethernetted to one of these. So the path is: router-switch to distribution switch to AE wireless to laptop. Big problem pulling another cable direct from the router to the AE. Moving the AE to the router puts it 100 feet and 4 walls away, no bars on the rf signal strength indicator. Am I screwed or what?

problem due to firewall settings - resolved

Using Airport Express with Comcast Digital Broadband/Telepony Modem

I recently converted from Comcast's broadband modem to their combined modem for digital phone and internet. I can't connect both my G5 and the airport express to the modem simultaneously. Airport express set-up configuration shows a broadband modem with 2 ethernet ports. My modem only has 1. The modem is Touchstone Telephony modem by Arris. Has anyone made this type of connection work with this modem?
Here is my set-up:
iMac G5 connected via ethernet to telephony/broadband modem (basement)
Airport Express (basement)
iBook G4 (1st floor)
I plan to purchase an airport express base and move the airport express to the 1st floor so I can use the iBook on the 3rd floor. Before I spend the money, I want to make sure this will work.
Thanks!
Soraya
Imac G4 Mac OS X (10.3.9)
Imac G4 Mac OS X (10.3.9)

Hi Soraya,
I assume your iMac G5 does NOT have a Airport Card?
It seems you will need a Router in order to get all your computers and the Airport Express to connect to the internet.
Linksys Routers at Compusa
My set up:
Comcast Broadband Cable Modem>Asante 4 port router>port 1 Mac G3, port 2 Airport Express and port 3 Powerbook G4 ( unless I use my Airport ).
hope this was helpful.....
Powerbook G4 1.67 15", 1 gig ram, 128 vram, 80 gig harddrive Mac OS X (10.4.8) Powermac G3 266 mt, Dell 5150,ibook G4, 1 gig shuffle, epson printers, airport

AirPort Express with USB - connect harddrive and use as time-capsule?

question: can I connect an external harddrive to the AirPort Express USB port and use it as a backup medium via wireless? In the tech specs its meant to be a USB port for a printer. help?

Hello jsmithko. Welcome to the Apple Discussions!
Sorry, but the USB port on the AirPort Express Base Station (AX) only supports USB printers (or a USB hub with multiple USB printers for the 802.11n version).
(ref: Uses for the USB port of Time Capsule, AirPort Extreme, AirPort Express)

Airport express won't connect to cable modem

We recently moved to a new residence and just had internet service installed by a technician. Unfortunately, I didn't have my Airport Express handy while he was here, so he simply connected my Macbook Pro directly to the cable modem via ethernet cable. When I found my Airport Express, I disconnected the Macbook Pro from the cable modem and connected the Airport Express to the modem via the same ethernet cable and powered up. The Airport Express began flashing yellow but the flashing yellow never did turn the steady green that indicates the Airport Express is receiving the signal. I called my internet provider but they don't deal with router issues. What can I do?

Cable modems "remember" the device that is connected. Your modem is "remembering" your computer and looking for it when you connect the AirPort Express, so it will not connect to the AirPort Express.
You need to push the reset button on the modem and then power off the modem
Power off everything else on the network...all computers and devices
Wait 15 minutes
Make sure that the ethernet cable from the modem is connected to the AirPort Express
Power up the modem only and let it run 3-4 minutes by itself
Power up the AirPort Express and let it run a few moments
Power up each computer and device one at a time
Check for proper operation.
If...you are switching from a previous DSL service to cable, you may need to reconfigure the AirPort Express. Post back for more info on this.
Message was edited by: Bob Timmons

How do I setup Airport express with ethernet connection to my modem?

Similar Messages

Maybe you are looking for