How do I use the front panel audio/video jacks?

I have a Pavilion HPE-480t desktop and can't find documentation anywhere on how to use the front autio/video jacks. When I hook up a device no software automatically loads. Is there a supplied program that recognizes them?
This question was solved.
View Solution.

Hi,
Based on this, your machine can have ONE of the following combinations at the front, I use the last one to answer your question:
15-in-1 card reader + 1394 + 2 USB + 1 headphone jack + 1 microphone jack
15-in-1 card reader + HP USB 3.0 SuperSpeed PCIe x1 card + 1394 + 2 USB + 1 headphone jack + 1 microphone jack
15-in-1 card reader + 1394 + 2 USB + 1 headphone jack + 1 microphone jack + Audio L/R + S-video + Composite Video
15-in-1 card reader + HP USB 3.0 SuperSpeed PCIe x1 card + 1394 + 2 USB + 1 headphone jack + 1 microphone jack + Audio L/R + S-video + Composite Video
Card reader: you can use it to read memory cards (normally from digital cameras or video cameras).
USB3: newer USB port(s) which can run 10 times faster than USB2
1394 or Firewire port: also normally for video cameras, many machines do not have it now
USB: normal USB 2 ports
Headphone jack: for headphone, earphone or external speakers
Microphone jack: For a microphone
Audio L/R: color coded for left and right audio channels, it does not say in or out.
S-video: Connect to additional monitor/TV, Many modern monitors/TV's now do NOT use this port.
Composite Video: also color coded (yellow). Connect to additional monitor/TV, Many modern monitors/TV's now do NOT use this port.
Regards
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Is there possibility to use the front panel without installing Labview?

Hallo,
i have two small questions:
1- Is it possible to use the front panel of a labview software without needing to install Labview itself? i mean something similar to the "power point viewer" which can view the Power Point files without installing the microsoft office.
2- In an intensity Graph, how can one change the color?
thanks.
Solved!
Go to Solution.

Hi,
Regarding your questions
1)You need to have Labview and Application builder installed on your machine. If you have that you can make an stand alone application (EXE) and then you can deploy it on systems that does not have LabView and can view it, However you will not be able to see the block diagram.
Here is a link that explains how to do so
http://zone.ni.com/reference/en-XX/help/371361A-01/lvhowto/exe_ex/
2) You can either do it by using propery node or marker method. The following link explains it
http://digital.ni.com/public.nsf/allkb/1ADFF221E27F5B5886256E6F007C7B58?OpenDocument
Hope it helps.
Regards,
Fawad
Fawad Nisar
Applications Engineer
National Instruments UK & Ireland

How can I display the front panel of the dinamically loaded VI on the cliente computer, the VI dinamically loaded contains files, I want to see the files that the server machine has, in the client machine

I can successfully view and control a VI remotly. However, the remote VI dinamically loads another VI, this VI loaded dinamically is a VI that allows open others VIs, I want to see the files that contains the server machine, in the client machine, but the front panel of the dinamic VI appears only on the server and not on the client, How can I display the fron panel with the files of the server machine of the dinamically loaded VI on the client computer?
Attachments:
micliente.llb ‏183 KB
miservidor.llb ‏186 KB
rdsubvis.llb ‏214 KB

I down loaded your files but could use some instructions on what needs run.
It seems that you are so close yet so far. You need to get the data on the server machine over to the client. I generally do this by doing a call by reference (on the client machine) of a VI that is served by the server. THe VI that executes on the server should pass the data you want to diplay via one of its output terminals. You can simply wire from this terminal (back on the client again) to an indicator of your choosing.
Now theorectically, I do not think that there is anything that prevents use from getting the control refnum of the actual indicator (on the server) of the indicator that has the data, and read its "Value" using a property node. I have never tried this idea but it seems t
hat all of the parts are there. You will need to know the name of the VI that holds the data as well as the indicator's name. You will also have to serve all VI's. This is not a good idea.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

How can I use multiple front panel controls to be mirrors of each other?

Hi All:
I know this is going to be a strange question, but I have multiple inputs that control one output. This in itself not necessarily difficult, but I have a strange need. If one of the control inputs change I would like this to be indicated by the other controls. For example, I have a slider, numeric and dial controls on the front panel that control RPM. If the slider changes to 1000 RPM I would like the numeric and dial controls to see that change. Is this possible. If so, can you give me advice on doing this. I am using 7.1. Thanks for the help.
John Honnold

What you want is not that hard, but asked for a rather limited times.
Here's a how to:
Drop a slider
Right click Visible items-> Digital display
Right click on the slider Advanced-> Customize
Right click on the Digital display Replace select the control you want to replace it with (a gauge for instance)
Right click on the Gauge Visible items -> Digital Display
Now you have one control with three control options:
This was done in 8.2 but I think the same goes for 7.1
Ton
Message Edited by TonP on 04-06-2009 09:52 AM
Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
Nederlandse LabVIEW user groep www.lvug.nl
My LabVIEW Ideas
LabVIEW, programming like it should be!
Attachments:
Example_VI.png ‏7 KB

How can I arrange the front panel?

Hello,
I’m using LV 7.1 and created a VI with many controls and indicators. It writes and reads data to and from a bus system. For that I used the flat sequence structure and many case structures.
Now I would like to order the front panel, i.e. by using the tab control only the data read or only the user settings should be displayed.
But using the tab control slows the whole VI down, so that a data recording in real time is impossible.
Are there any other possibilities to bring the front panel into order if the number of controls and indicators is too high for the screen?
Thanks in advance,
UoS

Do you mean that the CPU usage goes up and the PC responds slowly. If so, this is interesting. This is most likely related to a grphical element causing the system to slow down. The tab control should theoretically take care of this, but about a year ago I ran into a similar situation where a tab caused problem here. In that case it looked like controls that were partially displayed caused the problem and when using the tab control the problem was there even when displaying another page. If this is so, you can try to determine the source by scrolling the screen in different directions. Once the problematic area is moved off the screen the VI should run faster. This way you can tell which area has the problem.
Try to take over the world!

How do I get the front-panel to pop to the front of the screen?

I have a program that is reading in some network files. When a certain part of the file has been changed I want to pop up the front panel and blink the changed area. The blinking is easy and I can get the VI to pop to the front of any other running LV stuff (using the IsFrontmost vi property) but I need the vi to pop to the front of the entire screen and whatever else is running (Excel or the such). Any ideas on this? I'm doing the development on LV 6.1 on Win2k.
Thanks,
Gary

Mache wrote:
Hi Gary,
There is one thing I think you may have to do. If the window is minimized than it will try to make it topmost but the minimize will take precedence, so you will see the task bar blink and the OS stays in the active/current window. Try to use the "restore window" vi before trying to make it topmost. That should work.
Also make sure that, the LV window you are trying to restore and make topmost is not superceded by another LV modal window.
Thats my take, Let me know if that works, for future reference.
Good Luck
Mache
I've tried putting in the Restore Windoe vi and the results are the same. Both of those functions (seperate or together) result in the window moving to the top of the other LV screens only. If I have Word or explorer or anything else open, that window will stay on top and the task bar flashes. Can I use the "move window to front" vi in my main vi to move my main vi's front panel to the front? If not are there any ways to get around this? My program is mostly running in the background but when there's an important change I need it to move to the front and take precedence for a few seconds.

Need help badly!! how can i use the front camera i...

guys, i need help with the front camera of my device
how can i enable the front camera of nokia N900 to shoot photos or videos,
this problem is really bugging me...
need help badly...

You can't.. it is terrible..
the only app that really uses it is mirror
Open this link on your phone to install mirror
http://maemo.org/downloads/product/raw/Maemo5/mirror?get_installfile
the camera firmware is bad, so the image quality is truely terrible.. play with mirror to see.. it may be fixed in a future firmware release (it *IS* better than it was.. the firmware last year had a line through the picture!)

How do I keep the front panel on top of every windows (including non-LabVIEW windows)?

The question above states it all. Basically I have a progress bar the tells the user to wait and I want it to remain in front of anything that pops up while it is running. My program opens up and deploys a VeriStand project and while it is doing that I dont' want the user to be able to do anything in the front panel that launches it. When VeriStand launches it goes in front of the status window and you can't see it anymore. I want to prevent this from happening and keep it in front of any VeriStand windows that pop up when I call the executable and the deploy an SDF. I did take a look at the WINUTIL.llb but it keeps either 1) giving me errors or 2) not keeping it on top of anything but the main front panel.
Any fixes or alternative solutions would be much appreciated. Thank you.

I did read that earlier and I just think I don't know enough of what I'm doing with library calls to make it work. I kept getting errors and gave up on at the end of the day yesterday. I'm working on other problems since this isn't a major one and figured I'd post it and see if anyone already had a solution to it.
Thanks for the help though, it's appreciated.

How do I use the built-in audio input with AU Lab?

I just tried AU Lab for the first time, and I can't select an audio input.
The "Create New Document" window lets me choose "Built-in Output", but the pulldown for Input Source is greyed out. The area under the "Input" button says, "Audio Input Not Supported". How can it not support the built-in audio input? I even tried using SoundFlower to route the signal from the Line In (a small app) to the Input of AU Lab. AU Lab's display then shows two channels from Soundflower, but they are still greyed out.
All I want to do is get a signal from the built-in audio input routed to AU Lab so I can use AU effects to process the audio signal in real time. How do I do this?

They comes configured with your software. If you want to use, for example, Skype, you need to run the configuration wizard section.
Best regards.
IPnaSh
First Spanish Community Guru - Colaborador ad honorem

How can I enable my front panel audio??

the type of my mainboard is MS-6552,when I inserted my earphone and microphone into the jack of the box,I can hear nothing! then I opened the box,I found that the wire was not the proper place,there were 8 wires whick marked with “MIC IN,GND,LIN,LOUT,MIC IN,GND,RIN,ROUT”,I also found the F_AUDIO on the mainboard,there were 18 pin on it,I cannot matching them! who can help me?thanx

Look through you mobo's manual and you'll find it... Don't get stressed out too early... The first computer I built myself got me stuck in the same area for hours!!!
Btw, you've got to remove the jumpers on your mobo to enable front panel sound. Be warned that most mobo only allows you to us either front panel or back panel sound only. Please also ensure that there are no stand offs underneath your mobo.
All the Best... :D!!!

How can I use the accordion panel widget with a footer?

Hi,
My question is may be not clear. So I'm gonna be more specific. I'm using a menu for my website with the accordion panel widget. The menu is working fine and when I'm opening it, it pushs the items below on the pages.
My problem is with the footer of the page. Because, when the items below the widgets are pushed, they go below the footer and the footer is not pushed.
Is there any way to pushe the footer when I use the accordion widget? I don t want to overlap it.

I assume this is what you want to achieve in the footer....
Make sure in Muse before you export that the panel is closed, and also as Brad suggested, make sure Overlap Items Below is unchecked. I would also check the "Can Close All" button.

How can i change the setting for audio-video for my face time to built in only so i can have my skype camera ?

Good evening,
The last few days my I lost the ability on Skype to be seen by the other party ... I can see them but they cannot see me. At the same time my Face Time sent me some messages error.
When I open my Skype and go to Preference and go to audio/video I see my image ... and when I go back to make a call the camera is off (no light). When I look at the bottom where I can have a drop down arrow I have Face Time (built in).
On my other Macpro (that work well) I have at the same place built-in only.
Cannot change anything on my MacBook air ... no drop in.
Please Help and thank you !

There are no settings for video resolution or frame rate.
Regarding iOS developer policies:
https://developer.apple.com/devcenter/ios/index.action

How can put on the front Panel the Bolean controll to activate stack plot2 mode?

In the properties of Waveform Chart there is the possibility to show all charts in one monitor or the Stack Mode Plot. Can I put a bolean Controll to use this stack plot in run time by Control Panel?
Thanks,
Vanny
Sweet, Beautiful and Young Female Physicist (SBYFP)
(I speak a not very good english, so If U are Italian LabVIEW expert speak in Italian, if U speak in Eglish... please speak easy )
My e-mail for personal contact: [email protected]_NO_SPAM_PLEASE

You can't change between stacked or overlay mode at runtime. You could use two different charts and make one or the other visible/invisible.

How can I use the tabbed panel with the accordion panel options of close all panels and over/not overlap the items below?

Ideas for features in Adobe Muse

I assume this is what you want to achieve in the footer....
Make sure in Muse before you export that the panel is closed, and also as Brad suggested, make sure Overlap Items Below is unchecked. I would also check the "Can Close All" button.

How do I use the skin for a video object in one of my slides?

I put an video object place holder in one of my question masters, and when I insert a video into the actual project slide, it will not play with a skin. I can set it up to play automatically, but when I add a skin to it, the functions of the skin won't work. Any suggestions?
Ryan

Hi DonTimo,
I've tried doing that, but in the said folder there are only default pictures. I can't find the images of any contacts in the app "Contacts" anywhere. The thread you refered me to and many others that are smilar to it, date back to about 2009-2010.
Really need this photo. Any other pointers?

How do I use the front panel audio/video jacks?

Similar Messages

Maybe you are looking for