How do u show the percent of the battery on the iphone 4s

how do u show the percent of the battery on the iphone4s

Settings > General > Usage Battery Percentage.
As in the manual, available at http://support.apple.com/manuals/ or downloadable from iTunes as an iBook.

Similar Messages

  • How do i show a movie from my mac to the television?

    how do i show a movie from my mac to the television?

    Hello there, kojak100.
    The following Knowledge Base article goes over how to sync content to your iPad:
    iOS: How to transfer or sync content to your computer
    http://support.apple.com/kb/ht1296
    This section may prove useful:
    USB syncing
    Open iTunes.
    Connect the iOS device to your computer using the included USB cable and click the device button in the upper right corner. (If you are viewing the iTunes Store, click the Library button in the upper right corner. The device button will then be visible.) Some tabs may not appear if you do not have corresponding content in your library. For example if you do not have any podcasts in your library, the corresponding Podcasts tab will not appear.
    You can configure the different content types in each tab. For example, movies under the Movies tab.
    To sync, click Apply, in the lower-right corner of the screen.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • What to do if upon charging after a few minutes it shows the plug symbol on battery but the green battery icon on the main screen is still half?

    what to do if upon charging after a few minutes it shows the plug symbol on battery but the green battery icon on the main screen is still half?

    One of two things usually. Less often charger is faulty, try another charger. Most often the plug symbol in this situation indicates faulty battery.
    Try a Reset, hold both home and power buttons until the iPhone restarts itself, ignore the "slide to power off" let iPhone restart itself.

  • How much does it cost to replace a battery for the iPod classic?

    How much does it cost to replace a battery for the ipod classic?

    Depends on if you have Apple do the job or a third party repair company.  Apple will charge you $59 to swap the battery out.
    http://www.apple.com/batteries/replacements.html
    You may be able to find 3rd party service centers that do it for less.
    B-rock

  • How do i show date and time info of videos in Iphone as they appeare before import in iPhoto?

    How do i show date and time info of videos in Iphone as they appeare before import in iPhoto? or even as they appear on the iPhone itself? The selection on tool bar for show info is greyed out.

    Welcome T G Brown to the  iMovie boards..
    the socalled timestamp is within the imports.. if you select a clip in iM and hit the key combo Apple-I, you can see recording time and date.
    unfortunately, this info isn't delivered to any software. Bruce Gee (geethree.com, excellent plug-in maker) told us, there's no 'API' he could use for such a feature...
    same on the pro side, read this discussion at the FinalCutExpress boards:
    http://discussions.apple.com/message.jspa?messageID=7982935
    Forum member Ian offers a solution with a 3rd party app ....
    so: pen&pencil and typing timestamp manually into any 'Title' seems to be your only option...

  • How do I show and/or update image info in the Grid view?

    Somehow, all the info that was showing in my grid view, in Lightroom 5.6, disappeared. How do I view info for each grid image, on the grid and how do I update or change what info is viewable?

    Ctrl/Cmd-J

  • How can I show a pop up menu based on the selection in a previous pop up menu?

    For example, if "Company" is selected in a pop up menu in C6, then show another pop up menu in C7. if "Bob" is selected in a pop up menu C7, show another pop up menu that contains the talks "Bob" has in C8.
    I am trying to create a talk scheduling spreadsheet with different talk outlines for different speakers. I'm not sure if there are any functions or formulas that can accomplish this. Can anyone help?

    Pop-up menus contain fixed values in Numbers. You might be able to do this using Steppers or sliders. These produce a numerical result, which could be used to direct a second slider or stepper's output to a specific column or table.
    If you can provide a map of the structure of your list(s), there may be someone here able to take on the task of constructing the tools to do the job.
    Regards,
    Barry

  • How do I show and hide a popup message by the program

    Hi,
    I've the following problem. Sometime the program must wait to open a seriel port. On slow machines, this could take some seconds.
    During this time I'll display a popup message with the message "please, be patient....".
    After the port is open, the message should be hide by the program.
    JOptionPane could be good, but without a "OK" button. Everthing should be controlled by the program.
    I would implement the Runnable interface for the showing of the popup message.
    Any ideas? Thanks in advance.
    Hans

    You can use a JDialog... this will act like JOptionPane, but you can put on it whatever components you like... so no OK button!
    For example:
    JDialog dialog = new JDialog(parentFrame);
    dialog.add(new JLabel("Please be patient", BorderLayout.CENTER);
    dialog.pack();
    dialog.setLocation(100,100);
    dialog.setVisible(true);
    dialog.setVisible(false);

  • How do i show a popup in an OA Pageon the basis of some database validation

    Hi All
    I need to show a popup message on the click of a button.
    On the click of the button I have to submit the page and do some database validation with the data entered by the user on that page.
    Depending on the validation I have to give a popup which will have a value that is fetched from tha database.
    I can show a popup by writing the below given code in the processRequest of my CO
    OASubmitButtonBean registerbutton = (OASubmitButtonBean)oawebbean.findChildRecursive("RegisterButton");
    registerbutton.setOnClick("alert('show an alert')");
    But I cannot perform the database validation(using a stored procedure) in the processRequest.
    I am performing the validation in the processFormRequest
    Also I am not able to show the value fetched from the database in the popup using the above alert.
    Please send me the code.
    Thanks in advance.
    Regards
    Meenal

    okay so the popup window would be some information window, where the user, maybe after reviewing the information presses close and closes the window.
    i would do this using PPR, have a small content region or some other small region(which supports PPR), which would showup in some section of the screen when the user performs the desired action, and have a close button in the region, pressing close would fire PPR again and hide this region.
    There maybe variety of solutions such as this depending on the requirement.
    Thanks
    Tapash

  • How do i show hidden files on my usb on the imac (not to delete)

    i am trying to use the usb for the xbox and it keeps asking me to format so i just need to move the files from the usb untill it is all done

    where on my computer am I suppose to make the individual picture files and have them to upload on my ipod touch.... I do have a photo library on my computer, but in the photo tab in itunes for the ipod touch and there is nothing checked for syncing, cause when I do check it it always says its going to replace everything i have in my photo library on my ipod touch.....  So how am i suppose to have it checked and have it NOT replace pictures on it????
    Also I cannot make more photo albums into my ipod touch, it just replaces the one album every time....
    I am very frustrated cause I have tried the manuals and the apple support help etc and nothing pertains to my exact issue.....
    Please if u could elaberate I would appreciate it alot..... 
    thank u

  • HT4528 About 30 minutes ago, my iphone 4 screen just went white. It still shows the time, signal and battery at the top, but everything else is white. I can't receive calls/text messages. My phone will not lock or turnoff,  but it will charge. HELP!!

    I don't know what to do. My iPhone 4 just all of a sudden had a blank white screen. It still shows the bar at the top with the signal, time, and battery life. But the rest of the screen is white. If I touch the screen it acts like it's selecting something and gives me the choice to "Copy". It will still charge when I plug it up, but i cannot turn it off or lock the screen. I tried leaving it alone for awhile to see if it will lock on its own, like it normally would, and all it does is dim the screen. I guess im going to try to just let it die, and then see what happens, but if anyone else has any suggestions (other than taking it in to be looked at or getting a new phone) I would greatly appreciate it!

    Any number of things could have caused the phone to do this. If after the reset you are experiencing additional problems, the next step in the troubleshooting process is a restore from a backup. Make sure you have one before you start the restore process. If that does not improve things, then you may have to restore as a new device. Remember, restoring as a new device will delete all data off the phone. Make sure all of your pictures are imported to the computer and all other data is synced to supported applications on the computer before restoring as new. See this support document about backups http://support.apple.com/kb/HT4946, and this about restoring the phone. http://support.apple.com/kb/HT1414

  • Getting  a low battery sign only  ,changed battery still the same thing

    my ipod video stopped charging for no reseason all it says is low battery and get the sad apple face and to contact apple. my computer doesn t reconize the ipod or nothing .i figured it was a bad battery so i bought one installed it still doing the thingno thang is there anything i can try or is my ipod toast .any ideas anyone,should i call support and paythere fee to find out its broken

    If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
    http://docs.info.apple.com/article.html?artnum=60983
    If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
    Make sure you do all the following “TRYs”
    A. Try to wait 30 minutes while iPod is charging.
    B. Try another FireWire or USB through Dock Connector cable.
    C. Try another FireWire or USB port on your computer .
    D. Try to disconnect all devices from your computer's FireWire and USB ports.
    E. Try to download and install the latest version of iPod software and iTunes
    http://www.apple.com/itunes/download/
    For old and other versions of iPod updater for window you can get here
    http://www.ipodwizard.net/showthread.php?t=7369
    F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
    http://www.apple.com/support/ipod/five_rs/
    G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
    http://docs.info.apple.com/article.html?artnum=93651
    If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
    Intermediate Level
    A. Try to connect your iPod with another computer with the iPod updater pre-installed.
    B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
    For Mac computer
    1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
    2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
    3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
    4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
    5. Eject your iPod and do a Reset
    6. Open the iTunes 7 and click “Restore”
    For Window computer
    Go to folder “My Computer”
    Hope you can see your iPod there and right click on the iPod
    Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
    Now select “Format”
    Eject your iPod and do a Reset
    Open the iTunes 7 and click “Restore”
    In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
    http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
    C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
    Tips
    a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
    b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
    c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
    http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
    Advance Level
    A. Diagnostic mode solution
    If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
    You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
    Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
    iPod 1G to 3G: "Menu" and "Play/Pause"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
    The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
    iPod 1G to 3G: "REW", "FFW" and "Select"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
    You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
    Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
    B. Format your iPod with a start disk
    I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
    If none of these steps address the issue, your iPod may need to be repaired.
    Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
    Or visit your local Apple Retail Store http://www.apple.com/retail/
    In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
    http://www.ipodresq.com/index.php
    http://www.ifixit.com/
    Just in case that you are at the following situation
    Your iPod warranty is expired
    You don’t want to pay any service charges
    You are prepared to buy a new one
    You can’t accept the re-sell value of your broken iPod
    Rather than leave your iPod as paper-weight or throw it away.
    You can try the following, but again, only do it as your last resort and at your own risk.
    Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
    Last Resort Level
    1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
    In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
    http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
    2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
    http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
    Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
    2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
    Exclamation point and folder and nothing else
    Spank your iPod
    http://www.youtube.com/watch?v=3ljPhrFUaOY
    http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
    Exclamation point and folder and nothing else
    http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
    What should I do with my iPod? Send it or keep it?
    http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
    Strange error on iPod (probably death)
    http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
    Sad Face on iPod for no apparent reason
    http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
    Meeting the Sad iPod icon
    http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
    Sad faced iPod, but my computer won’t recognize it?
    http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
    iPod Photo: unhappy icon + warranty question
    http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
    4th Gen iPod Users - are we all having the same problem?
    http://discussions.apple.com/message.jspa?messageID=2235623#2235623
    Low Battery, and clicking sounds
    http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
    Sad faced iPod, but my computer won’t recognize it
    http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
    Sad iPod solution
    http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
    Re: try to restore ipod and it says "can't mount ipod"
    http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
    iPod making clicking noise and is frozen
    http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
    Cant put it into disk mode
    http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
    I think my iPod just died its final death
    http://discussions.apple.com/thread.jspa?messageID=3813051
    Apple logo & monochrome battery stay
    http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
    My iPod ism’t resetting and isn’t being read by my computer
    http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
    I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
    Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
    Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

  • HT1320 Help! My ipod classic is frozen. Even when I attach it to a power source and try to reset it (as per the instructions above), the apple logo never appears. The only thing that happens is that the screen turns alternately light and dark. Thanks!

    Help! My ipod classic is frozen. Even when I attach it to a power source and try to reset it (as per the instructions above), the apple logo never appears. The only thing that happens is that the screen turns alternately light and dark. Thanks!

    If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
    http://docs.info.apple.com/article.html?artnum=60983
    If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
    Make sure you do all the following “TRYs”
    A. Try to wait 30 minutes while iPod is charging.
    B. Try another FireWire or USB through Dock Connector cable.
    C. Try another FireWire or USB port on your computer .
    D. Try to disconnect all devices from your computer's FireWire and USB ports.
    E. Try to download and install the latest version of iPod software and iTunes
    http://www.apple.com/itunes/download/
    For old and other versions of iPod updater for window you can get here
    http://www.ipodwizard.net/showthread.php?t=7369
    F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
    http://www.apple.com/support/ipod/five_rs/
    G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
    http://docs.info.apple.com/article.html?artnum=93651
    If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
    Intermediate Level
    A. Try to connect your iPod with another computer with the iPod updater pre-installed.
    B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
    For Mac computer
    1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
    2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
    3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
    4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
    5. Eject your iPod and do a Reset
    6. Open the iTunes 7 and click “Restore”
    For Window computer
    Go to folder “My Computer”
    Hope you can see your iPod there and right click on the iPod
    Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
    Now select “Format”
    Eject your iPod and do a Reset
    Open the iTunes 7 and click “Restore”
    In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
    http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
    C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
    Tips
    a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
    b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
    c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
    http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
    Advance Level
    A. Diagnostic mode solution
    If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
    You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
    Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
    iPod 1G to 3G: "Menu" and "Play/Pause"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
    The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
    iPod 1G to 3G: "REW", "FFW" and "Select"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
    You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
    Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
    B. Format your iPod with a start disk
    I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
    If none of these steps address the issue, your iPod may need to be repaired.
    Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
    Or visit your local Apple Retail Store http://www.apple.com/retail/
    In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
    http://www.ipodresq.com/index.php
    http://www.ifixit.com/
    Just in case that you are at the following situation
    Your iPod warranty is expired
    You don’t want to pay any service charges
    You are prepared to buy a new one
    You can’t accept the re-sell value of your broken iPod
    Rather than leave your iPod as paper-weight or throw it away.
    You can try the following, but again, only do it as your last resort and at your own risk.
    Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
    Last Resort Level
    1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
    In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
    http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
    2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
    http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
    Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
    2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
    Exclamation point and folder and nothing else
    Spank your iPod
    http://www.youtube.com/watch?v=3ljPhrFUaOY
    http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
    Exclamation point and folder and nothing else
    http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
    What should I do with my iPod? Send it or keep it?
    http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
    Strange error on iPod (probably death)
    http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
    Sad Face on iPod for no apparent reason
    http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
    Meeting the Sad iPod icon
    http://askpang.typepad.com/relevant_history/2004/11/meeting_the_sad.html#comment -10519524
    Sad faced iPod, but my computer won’t recognize it?
    http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
    iPod Photo: unhappy icon + warranty question
    http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
    4th Gen iPod Users - are we all having the same problem?
    http://discussions.apple.com/message.jspa?messageID=2235623#2235623
    Low Battery, and clicking sounds
    http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
    Sad faced iPod, but my computer won’t recognize it
    http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
    Sad iPod solution
    http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
    Re: try to restore ipod and it says "can't mount ipod"
    http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
    iPod making clicking noise and is frozen
    http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
    Cant put it into disk mode
    http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
    I think my iPod just died its final death
    http://discussions.apple.com/thread.jspa?messageID=3813051
    Apple logo & monochrome battery stay
    http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
    My iPod ism’t resetting and isn’t being read by my computer
    http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
    I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
    Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
    Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

  • Unibody 13" MB Dec 2008 - can I upgrade the battery to the new 7hr battery?

    Can I upgrade the 3hr removable battery in my Dec 2008 Unibody MB 13" to the built-in 7hr battery in the new 13" unibody MBP?

    No.

  • OS 5 is the origin of battery problem not iPhone 4S

    The new version of OS 5.0.1 decrease in a very important way the duration of my battery of my iPhone 4. The problem comes from the OS 5 not iPhone 4S. Are you all right?

    The vast majority of apps cannot and do not run in the background.  For more info on Multitasking...
    http://support.apple.com/kb/ht4211
    http://whenwillapple.com/blog/2010/04/19/iphone-os-4-multitasking-explained-agai n/
    http://www.macworld.com/article/1164616/how_ios_multitasking_really_works.html
    http://speirs.org/blog/2012/1/2/misconceptions-about-ios-multitasking.html

Maybe you are looking for

  • When trying to open final cut pro 7 I get the following error:  EXC_CRASH (SIGABRT)

    Process:         Final Cut Pro [1077] Path:            /Applications/Final Cut Studio/Final Cut Pro.app/Contents/MacOS/Final Cut Pro Identifier:      com.apple.FinalCutPro Version:         7.0.3 (7.0.3) Build Info:      FCPApp-1008261348~8 Code Type:

  • IPhone 2.0 Update let down on original iPhone!!!

    APPLE, YOU HAVE TO BE KIDDING ME!!! HAS ANYONE NOT NOTICED THAT THE SPEAKER VOLUME FOR YOUR IPOD ON THE ORIGINAL IPHONE HAS GOTTEN MUCH MUCH LOWER? I NOW HAVE TO PUT MY EAR UP TO IT TO LISTEN TO THE SONG! WOW, IT IS SOOOO LOW? AM I ALONE? SO ANNOYING

  • BT cordless phone battery rating and use as a char...

    Hello, Can I use any mAh rating of rechargeable batteries in my cordless phone? Can I use my phone as a general battery charger? I've got two old cordless phones in use, the main one is a Bt Esprit 1250 (takes AAA batteries) and the spare a BT Divers

  • Error in Context menu

    Hi, I used the front office process DISCON02 in transaction to create disconnection. When I test it in the CIC screen, it is giving an error as follows. Workflow WS20500081 could not be started. What to do? Thanks, Goksilin

  • Cannot open itunes get .rbf problem.  Will not reinstall

    I tunes quit on my computer.  I get this message file 357ea26a.rbf  windows looking for applcation to open. I try to redown load and nstall.  I get installation error.