How do you keep aggr permanent across reboots on Sol 10?

How can I keep my aggr permanent across the reboot?? The steps in the manual don't work for my system. It is the 1/06 build and the latest patch cluster has been added. (Kernel 118833-36)
I created an aggr with bge1 and bge2 and enabled LACP on the NICs
#dladm show-link
bge0 type:non-vlan mtu:1500 device:bge0
bge1 type:non-vlan mtu:1500 device:bge1
bge2 type:non-vlan mtu:1500 device:bge2
bge3 type:non-vlan mtu:1500 device:bge3
#dladm create-aggr -d bge1 -d bge2 -l active 1
#dladm show-aggr
key: 1 (0x0001) policy: L4 address: 0:3:ba:f8:13:aa (auto)
device address speed duplex link state
bge1 0:3:ba:f8:13:aa 0 Mbps unknown down standby
bge2 0:3:ba:f8:13:ab 0 Mbps unknown down standby
#ifconfig aggr1 plumb 192.168.30.110 up
#ifconfig �a
lo0
bge0: flags=1000843<UP, BROADCAST, RUNNING, MULTICAST, IPv4> mtu 1500 index 2
inet 192.168.30.253 netmask ffffff00 broadcast 192.168.30.255
ether 0:3:ba:f8:13:a9
aggr1: flags=1000843<UP, BROADCAST, RUNNING, MULTICAST, IPv4> mtu 1500 index 3
inet 192.168.30.110 netmask ffffff00 broadcast 192.168.30.255
ether 0:3:ba:f8:13:aa
#vi /etc/hostname.aggr1
192.168.30.110
I rebooted and I am getting a �aggr1 failed to plumb�
I tried to
#ifconfig aggr1 plumb 192.168.30.110 up
and get �ifconfig: plumb aggr1: Invalid argument
I tried
#dladm show-aggr
and get nothing returned
I tried
#dladm create-aggr �d bge1 �d bge2 1
and get �dladm: create operation failed: File exists�
So I have to do a
#dladm delete-aggr 1
so I can create a new one and start the whole process over again.

Thanks to smorris@
bug 6369648 (link aggregation interfaces missing after reboot).
This has been resolved in patch 120990-02 (SunOS 5.10: net-physical
Patch)
I applied the patch and put the aggregate address in the file, /etc/hostname.aggr1 and it remained across reboots.

Similar Messages

How do you share Aperture file across multiple users on same Mac?

How do you share Aperture file across multiple users on same Mac? Seems this should be a preferences choice.

When you share your library between users, you may run into permission and ownership problems, if both users are editing the Aperture library and not only reading it. To avoid that, it helps to put the Aperture library onto a separate disk or a separate partion of your hard drive. For s separate partition or disk you can enable the "ignore ownership on this volume" flag. Then all users can access the library as owners of this library.
You might try to put the aperture library into a shared folder on your mac, but that has caused problems recently, i.e. when the library also contains video files.
Regards
Léonie

How can you keep your iPhone 4 (using it as my car's iPod) staying on the Audible app? When I leave the car and return to continue hearing a book, it has switched to iTunes.

How can you keep your iPhone 4 (using it as my car's iPod) staying on the Audible app? When I leave the car and return to continue hearing a book, it has switched to iTunes.

The first time an iPhone is connected to iTunes that is used to sync with another iPhone or iOS device, you are prompted to transfer the backup for the other iPhone or iOS device or to set up the iPhone as a new iPhone.
The former does as provided - it transfers the backup for the other iPhone or iOS device to the iPhone replacing all data on the iPhone that is included with the backup being transferred. The latter does nothing allowing you to make your various selections for the iPhone sync preferences with iTunes.
This is designed to be done right away with a new iPhone.
If you don't have a backup for the iPhone with iTunes on your computer and don't have an iCloud backup that hasn't been updated since choosing to transfer the backup for your iPod Touch to the iPhone, the data that was on the iPhone is gone.

How do you keep your message from appearring on a locked screen

how do you keep your message from appearring on a locked screen

Go to SETTINGS --> NOTIFICATIONS --> MESSAGES
Change "View in lock screen" to OFF
That should sort it for you.

HT4489 this is ridiculous! how do you keep the size of the picture for a contact that small? it is usually a piece of a lager picture... any way to make the size of the pictures the 224 KB they want? I always thought the application cropped the picture t

this is ridiculous! how do you keep the size of the picture for a contact in the address book that small? it is usually a piece of a lager picture... any way to make the size of the pictures the 224 KB they want? I always thought the application cropped the picture to fit their requirements...
Help
Leo

Gem
Events are organised strictly on date and time, as read by iPhoto from the Exif data in the Photo. You cannot manually sort.
Create Albums. You can do much more organising with Albums, use Photos from different events, place them as you will. Best of all, Albums use no disk space at all. They simply reference the file on the Hard Disk. So a pic can be 1, 10 or 100 Albums with no wasted disk space whatever.
Regards
TD

How do you keep your purchased apps if you are forced to change your Apple ID?

How do you keep your purchased apps if you are forced to change your Apple ID? A good example is if you are forced to change your email, which you use as your Apple ID. what if it is a security app and you lose a lot of data if you lose the app? Why are the apps tied to the Apple ID rather than the user? Why is it impossible to globally change the Apple I D?

All content is tied to the account, but you can change the primary email address on an account e.g. you can log into your account via the Store > View Account on your computer's iTunes and there should be an Edit button to the right of your account id on your account's page, or similarly on your iPad try tapping on your id in Settings > iTunes & App Store and view your account. Or you can update it by logging into it via this page http://appleid.apple.com . You shouldn't lose any content on the account if you update it.
After updating the account you may need to log out of your iPad by tapping on your id in Settings > iTunes & App Store and then log back in with the updated version for it to be 'refreshed' on it

How do you keep your VPN clients up to date?

Hi, how do you keep your Cisco VPN clients up to date? Our users connect to a Cisco 3015 Concentrator. It needs to be as automatic as possible.
Thanks

Check this link,
http://www.cisco.com/en/US/docs/security/vpn_client/cisco_vpn_client/vpn_cli
ent46/administration/guide/vcAch3.html
Example:
Steps to perform an automatic update for VPN client :
===================================================
1. Download update-4.8.00.0440-major-K9 file on your PC from the link below and unzip it.
http://www.cisco.com/cgi-bin/tablebuild.pl/vpnclient-3des
It will have the following files::
- binary_config.ini
- sig.dat
- vpnclient-win-is-8.00.0440-k9.exe
- vpnclient-win-msi-8.00.0440-k9.exe
2. Create a webserver with a folder and move all the above files to this folder on webserver.
3. Now on your vpn client create a new profile. This profile file will appear in the profiles folder of the vpn client. Copy this file to your desktop and zip it. Name the
zipped file as profiles.zip. Delete the profile from the client.
4. Make a copy of your binary_config.ini on your desktop. Rename it to new_update_config.ini. This is just to make sure its not saved as a txt file.
Open the above file and write the following on it:
[Autoupdate]
Required=1
5. Now move the new_update_config.ini and profiles.zip to the webserver. Once we browse to the webserver it should look like --
http://webserver/~razshah/vpn_profile_update462/
Index of /~razshah/vpn_profile_update462
Name Last modified Size Description
Parent Directory 09-Mar-2005 13:24 -
binary_config.ini 09-Mar-2005 13:26 1k
new_update_config.ini 11-Mar-2005 11:35 1k
profiles.zip 09-Mar-2005 13:26 1k
sig.dat 09-Mar-2005 13:26 2k
vpnclient-win-is-4.6..> 09-Mar-2005 13:26 7.6M
vpnclient-win-msi-4...> 09-Mar-2005 13:26 10.3M
6. The concentrator is configured as follows:
Client Type is Windows
URL http://webserver/~razshah/vpn_profile_update462
Revisions 4.6
7. On your PC go to the VPN Client > updates folder. Delete the update_config file if its already there. This folder should have only autoinstall (this file will be added if update works) autoupdate header files.
The update does take about 5 mins. To see the new file we have to close and reopen the client. Once connected make sure you are able to browse to the webserver and see all the files.
1- Auto update runs only on Windows 2000 and Windows XP, all other client types update manually. Windows NT users get notified and can get an update manually from the update server.
2- Remote users must have the VPN Client for Windows 4.6 or greater installed on their PCs to use the automatic update feature.
Regards,
~JG

HT4236 How do you keep photos in the same sequence on the iPhone that they are on the PC folder?

How do you keep photos in the same sequence in the iPhone as they are in the folder on the PC??

When I sync my photos they are listed alphabetically (by folder) and within the folders, listed alphabetically again by the name assigned to the photo. The only way I can think of to keep the order that you have in your computer would be to assign a letter as a prefix to each photo. If you have more than 26 photos in a folder, you can double the letters, etc. I think that will keep the photos in the order you want.

When burning a playlist to disc, how do you keep the songs in original order?

When burning a playlist to disc, how do you keep the songs in original order?

If you are burning an audio CD, they will burn in sequential order as in your playlist.
If you are burning an MP3 CD or a data CD, they will burn as individual files, and can be sorted any way you like when you view the CD. For an MP3 CD, the files will be prepended with a sequence number, so if you sort by filename, they will be in the original order.

How do you keep the browser heading from showing?

How do you keep the browser heading from showing in the
output? I did this once but can't figure out how!
Thanks in advance,
Rosie

You asked...
quote:
Is there a way to shrink the application you're capturing so it
fits within a given capture window rather than requiring scrolling,
or would I have to go back to the application developers for that?
(I realize that would shrink the size of everything on the screen,
but in some cases, that would be worth it to be able to show a
window without scrolling.
If, by "shrink" ... you mean by using the AppSizer, the
answer is "not really". You can configure AppSizer to a defined
size, then with the mouse pointer double-arrowed on the "edge" of a
window, right-click and your window-size selections will appear in
the AppSizer "list" (that you set up) and can be selected there.
But there is no re-scaling of the window contents, if that is
what you mean, so the smaller window may now require scrolling.
But keep in mind that if you use the recording option for
"Software Simulation" > "Custom Size", you can then snap the
application window to that size...

Lightroom 5 make adjustments want to transfer to photo shop to make additional adjustments. how do you keep the adjustments made in lr5 when photo is transferred to photo shop

lightroom 5 make adjustments want to transfer to photo shop to make additional adjustments. how do you keep the adjustments made in lightroom 5 when photo is transferred to photo shop
I am not able to keep the changes made in light room when I transfer to photo shop

Something you need to understand. Unless you are using the latest version of Photoshop Elements, it's possible that some of the adjustments that you make in Lightroom won't transfer to Elements if you choose the option to open anyway. If you choose the option to edit a copy with Lightroom adjustments then Lightroom will create a TIF or PSD file (depending on your preferences), and that file will include all of the adjustments that you have made using Lightroom. Then you can finish your work in Photoshop Elements.
The process of transferring an image from Lightroom to Photoshop or Photoshop Elements involves the Camera Raw plug-in. It has to be used to interpret the Lightroom adjustments and apply those adjustments to the image after it has been converted. Files open in Elements or Photoshop or no longer raw images because those programs are incapable of editing raw image data. I don't know if this will help you in this situation. Feel free to ask if you have more questions.

How do you keep yourself well organized at work?

For documentation I use onenote which is synced to my owncloud server so i can use it when ever needed. I also use a mix of wundlerlist and spiceworks to keep track of all my to do items and issues and requests. My number one recommendation is find the best way that works for you documenting and make sure to stick to it. Writing or typing it down will make sure that you retain what you did that day!

I am about to begin my first IT career in about a week (as a help desk position.)
I'm very excited about my new career shift but am bit worried at the same time.
That being said, I have a question that I want to ask all of you guys out there who has been working in the field for a quiet some time.
How do you keep yourself well organized when it comes to documenting results?
I was taught to document EVERYTHING after you solve your assigned tickets.
Are there any great tools that could come in handy when you document things?
Plus, what would be a proper way of documenting?
Would you document every single steps you've tried to solve your ticket?
Any tips or suggestions would be appreciated.
Thank you!
This topic first appeared in the Spiceworks Community

HT3215 How do you keep the clock face showing all the time without the screen going dark?

How do you keep the clock face showing all the time without the screen going dark?

Thanks. I saw a number of answers to the same basic question after I posted my question and apparently there are ways to to keep it on but, as you said, it will drain the battery quickly.

How can you keep the highest iphone 4s Video quality the same when exporting it from iMovie.

How can you keep the highest iphone 4s Video quality the same when exporting it from iMovie.

InDesign's PDF export engine does not transcode your videos, they are embedded exactly as they were in the original file. The Flash Player runtime which displays video inside PDF files may not show a perfect match to Quicktime etc. because most video playback tools aren't designed for a color-calibrated workflow, but they should be close.
The playback quality (blocking and aliasing) will be affected if the clip is not playing at 100% (screen pixels != video pixels) and in PDFs with the standard video player widget, that will only ever happen when you use 'floating window' mode. PDF pages have physical dimensions, so viewing them at "100%" does not make them match screen pixels.
If you don't mind the video clip being smaller than the media annotation in which it's playing, then use my free upgrade to the Acrobat playback widget - VideoPlayerX - which maintains 1:1 pixel scale until the page is zoomed out too far for it to fit. You can install the widget into InDesign so it's used by default when exporting.

HT1689 How do you keep pictures from reloading with every sync

How do you keep pictures from reloading with every sync

What do mean by reloading? Once you sync the photos to the iPad they should not sync again. Is that what you are seeing? The progress bar is showing that the photos are being transferred all over again?

How do you keep aggr permanent across reboots on Sol 10?

Similar Messages

Maybe you are looking for