How do you leave your iMac when you're not using it?

Just curious..
Hey All..
I have a 24" iMac 2.8 with a 750GB Hard Drive. I tend to leave it on all the time shutting it down over night probably once a week. I have my settings to turn the display off after 5 minutes and turn off the hard disks "when possible". I just wondered if this was healthy or will it shorten the life expectancy of my pride and joy? I must admit that I do like to leave it on all the time. I leave my Time Capsule on all the time too...should I perhaps shut this down also?
I have the Applecare program which gives me some piece of mind with my iMac.
I'd be delighted and interested to hear how you all 'leave' your iMacs when you're not using them.
Kind regards..
~RICKY

I have my system plugged into a UPS and generally leave it sleeping. There's a window where I have it scheduled to wake up and then sleep again, but it I otherwise sleep it.
I suspect that sleep probably puts the least wear on your machine and is safe if you have a UPS. FWIW, an early 2007 24" iMac draws 3W of power when it's off, and 10W or so when asleep ( the newer models use less than 6W). During the boot process, power consumption will go 200-220W for ~1 minute. Normal usage it consumes about 100W. Idling, the machine will use between 70-100W depending on the screen brightness, and about 45W if the display is off and machine is idle. Playing something like WoW brings the power consumption up over the 200W mark.
The mechanical parts wear proportional to the number of times they are used (physical switches), and the electronic parts wear mostly based on the the result of cycles of temperature changes / surges of voltage. Pressing the power-button to power-on the Mac probably puts the most wear on the unit as a whole. That said, under normal circumstances you are not likely to put enough wear on anything but the hard disk to have it fail.

Similar Messages

How come you can not use more than 126GB of a 1.5TB diskdrive with LabVIEW Real Time?

How come you can not use more than 126GB of a 1.5TB diskdrive with LabVIEW Real Time?
This is only 8.3% of the available disk drive space!
http://digital.ni.com/public.nsf/allkb/E7E2F5657B6026358625750B007201A6?OpenDocument
National Instrument's solution is either reformat you drive to less than 126GB or replace the drive with one less than that size.
Please NI, tell me you are going to fix your LabVIEW Real Time soon, and that we won't have to wait for LabVIEW RT 9.2.1 in 2011 for this one to be fixed.
http://upload.wikimedia.org/wikipedia/commons/9/90/Hard_drive_capacity_over_time.svg
Drives as large as 126GB or more have been around since about mid 2002. That's about 7 Years now and LabVIEW Real Time STILL can't use drives larger that 126GB! Please NI. Do something.
We deserve fixes to the old versions of LabVIEW RT. How about updates to LabVIEW RT. Such as 7.0.2, 7.1.2, 7.6.2, 8.0.2, 8.2.2, 8.6.2.
We don't need new features or versions of LabVIEW RT such as 9.0 until we have some of bugs fixed in the existing versions.
Kevin.
Message Edited by kmcdevitt on 05-29-2009 03:39 PM
Solved!
Go to Solution.

Coq rouge wrote:
NI is not making the Real Time OS in house. I do not remember which firm that is making it. Anyway you are allowed to use a hard drive that has been partitioned. And 126GB is some space is it not? I remember Bill Gates declared one time that 640Kb ram should be more than enough for any PC application also in the future
Coq Rouge (formerly t06afre),
The RealTime OS is an NI Product that is purchased from NI.
NI may or may not outsource design, developement, or manufacturing of the products that it sells under its own Company name.
For this reason I would be concerned if I were a PXI Embedded Controller designer/developer in the United States.
Yes, 126GB is some space. I see that there are now 2TB drives available. 126GB would be 6.3% of a new 2TB drive. Should we all be happy with being able to use 6.3% of the available drive space. Moore's Law seams to be alive and well. Drives larger than 126GB have been readily available for 5 or 6 Years. This should not be a surprise to NI. Why don't they do something about it.
Thanks for the trivia on Bill Gates. I must have missed that one since I don't try to keep up with Microsoft. I believe that he is a wonderful person and he and his family are doing wonders for the world in their "retirement". The world needs more like him.
What I do remember is Steve Jobs telling us that we would never need more that 128MB and that we would never to need to do anymore software development because everything was already in the "ToolBox".
McKevin.

How do I turn AppleTV off when I'm not using it?

How do I turn off AppleTV when I'm not using it?

It actually goes to sleep instead of powering off. Apple TV only uses 6 watts of power. That would mean 10 Apple TVs would consume the same amount of power as one 60 watt bulb and that's when it's on (not in the sleep mode).
You can set it to go to sleep after 15 min., 30 min., etc. of inactivity in settings. I think the default is 15 min. That doesn't include watching a movie. You can also put it in the sleep mode in settings, but the easiest way is with the remote.
Hold the Play/Pause button on the reomte for 5 secs to put it to sleep. This only works from the main menu. To go to the main menu quickly, hold the menu button for 3 secs.
Source

When I use my IPhone 4S to view the Shaw Go Movie Central App when I am at home I only use WiFi which is automatic, I start watching a show and sometimes I will get a message like "you can not use your cellular for video playback" or something close to th

When I use my IPhone 4S to view the Shaw Go Movie Central App when I am at home I only use WiFi which is automatic, I start watching a show and sometimes I will get a message like "you can not use your cellular for video playback" or something close to that. Then I received an email from Telus saying I had used my 3G instead of Wi-Fi using 75% of my data. How can this happen when I'm on Wi-Fi at home? If it switched to 3G for some reason I should have been disconnected and not just transferred to 3G network using up my data. What is the fix for this??

It doesn't have to be that complicated, Verizon iPhones come unlocked, just tell VZ you're going on Holiday/Traveling and suspend the service, no need to pay for service if you're not going to be using it. Pick up local SIM cards in the countries of your choosing, pop them in, re-activate iMessage and you're set!
I recommend getting a SIM card from the Three network in England, they have great EU roaming rates and free like-home roaming in Italy.
Set your phone's region to match the country you're in, it'll save from some headaches when calling local/international numbers.
To answer your questions,
1. If you choose not to have a local SIM card, it is good to keep your phone in Airplane mode to save battery.
2. Make sure the two iPhones have different names to reduce sync/restore issues.
3. If husband has an iPhone also, you can chat with iMessage/Facetime, just give him heads up about the new number you'll have. Otherwise, use Whatsapp if he's got an Android. You can activate Whatsapp with your American number or the international number if you choose to get a SIM in Europe.
Also, Get the MagicJack app and/or Google Hangouts, both of those apps provide you with free calling to the USA and Canada using any internet connection. Google Voice is another good way to SMS across the seas.
Let me know if you need any more tips for iPhoning across the pond.

Re: How do you create and use "common" type classes?

Hi,
You have 2 potential solutions in your case :
1- Sub-class TextNullable class of Framework and add your methods in the
sub-class.
This is the way Domain class work. Only Nullable classes are sub-classable.
This is usefull for Data Dictionary.
The code will be located in any partition that uses or references the supplier
plan.
2- Put your add on code on a specific class and instanciate it in your user
classes (client or server).
You could also use interface for a better conception if needed. The code will
also be in any partition that uses or references the supplier plan where your
add on class is located.
If you don't want that code to be on each partition, you could use libraries :
configure as library the utility plan where is your add-on class.
You can find an example of the second case (using a QuickSort class,
GenericArray add-on) with the "QuickSort & List" sample on my personal site
http://perso.club-internet.fr/dnguyen/
Hope this helps,
Daniel Nguyen
Freelance Forte Consultant
http://perso.club-internet.fr/dnguyen/
Robinson, Richard a écrit:
I'm relatively new to forte and I'd like to know how can you handle utility
type classes that you want to use through out your application? Ideally
what I want is a static class with static methods.
Let's say that I have a StringUtil class that has a bunch of methods for
manipulating strings.
My problem is that we have code that runs on the client and code that runs
on the server. Both areas could use the StringUtil class, but from what I
understand, I have to create StringUtil in a plan and then create a server
object of type StringUtil. The server object will eventually get assigned
to a partition. That's not good since I really want the server object to
physically reside at the server end and at the client end. (Actually, I
don't want a server object, I just want to invoke a static method of a
static class).
Any clues on how to solve this problem would be appreciated.
Also, what is the url at Sage-it that has a summary of all emails that have
been posted to [email protected]? Perhaps this question has been
answered previously.
Thanks in advance
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>-
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Hi Richard,
Your question about "utility classes" brings up a number of issues, all of
which are important to long-term success with Forte.
There is no such thing as a static method (method that is associated with a
class but without an implicit object reference - this/self/me "pointer") in
TOOL, nor is there such thing as a global method (method not associated
with a class at all). This is in contrast to C++, which has both, and
Java, which has static methods, but not global classes. Frequently, Forte
developers will write code like this:
result, num : double;
// get initial value for num....
tmpDoubleData : DoubleData = new;
tmpDoubleData.DoubleValue = num;
result = tmpDoubleData.Sqrt().DoubleValue;
tmpDoubleData = NIL; // send a hint to the garbage collector
in places where a C++ programmer would write:
double result, num;
// get initial value for num....
result = Math::Sqrt(num);
or a Java programmer would write:
double result, num;
// get initial value for num....
result = Math.sqrt(num);
The result of this is that you end up allocating an extra object now and
then. In practice, this is not a big deal memory-wise. If you have a
server that is getting a lot of hits, or if you are doing some intense
processing, then you could pre-allocate and reuse the data object. Note
that optimization has its own issues, so you should start by allocating
only when you need the object.
If you are looking for a StringUtil class, then you will want to use an
instance of TextData or TextNullable. If you are looking to add methods,
you could subclass from TextNullable, and add methods. Note that you will
still have to instantiate an object and call methods on that object.
The next issue you raise is where the object resides. As long as you do
not have an anchored object, you will always have a copy of an object on a
partition. If you do not pass the object in a call to another partition,
the object never leaves. If you pass the object to another partition, then
the other partition will have its own copy of the object. This means that
the client and the server will have their own copies, which is the effect
you are looking for.
Some developers new to Forte will try to get around the lack of global
methods in TOOL by creating a user-visible service object and then calling
methods on it. If you have a general utility, like string handling, this
is a bad idea, since a service object can reside only on a single
partition.
Summary:
* You may find everything you want in TextData.
* Unless you anchor the object, the instance will reside where you
intuitively expect it.
* To patch over the lack of static methods in TOOL, simply allocate an
instance when required.
Feel free to email me if you have more questions on this.
At the bottom of each message that goes through the mailing list server,
the address for the list archive is printed:
http://pinehurst.sageit.com/listarchive/.
Good Luck,
CSB
-----Original Message-----
From: Robinson, Richard
Sent: Tuesday, March 02, 1999 5:44 PM
To: '[email protected]'
Subject: How do you create and use "common" type classes?
I'm relatively new to forte and I'd like to know how can you handle utility
type classes that you want to use through out your application? Ideally
what I want is a static class with static methods.
Let's say that I have a StringUtil class that has a bunch of methods for
manipulating strings.
My problem is that we have code that runs on the client and code that runs
on the server. Both areas could use the StringUtil class, but from what I
understand, I have to create StringUtil in a plan and then create a server
object of type StringUtil. The server object will eventually get assigned
to a partition. That's not good since I really want the server object to
physically reside at the server end and at the client end. (Actually, I
don't want a server object, I just want to invoke a static method of a
static class).
Any clues on how to solve this problem would be appreciated.
Also, what is the url at Sage-it that has a summary of all emails that have
been posted to [email protected]? Perhaps this question has been
answered previously.
Thanks in advance

HI, I need your help. How can I delete all data, when I do not have the special security code, which I didn´t remember ? I also think, that I never create this code before. But I cannot put my settings back.

HI, I need your help. How can I delete all data, when I do not have the special security code, which I didn´t remember ? I also think, that I never create this code before. But I cannot put my settings back.

You must remember the code, if you can't then take the phone and proof of purchase to an Apple Store.

How to get on your ipad when it is disabled

how to get on your ipad when it is disabled

FORCE IPAD INTO RECOVERY MODE
1. Hold Sleep/Wake button down and slide to turn off iPad
2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug.
5. Release Home button.
ON COMPUTER
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. Select "Restore iPad"...

Does logging out of Firefox when you're not using it save energy?

Have been reading about how much energy servers consume. If I log out of Firefox when I'm not using it, does that decrease the amount of energy servers are using?

If you've never replaced the hard drive, it could be slowing down - 3 to 5 years is the typical lifespan for a notebook hard drive.
Do you know how much RAM is in the computer?
If the computer mostly works OK, you may just need to invest in it a little - replacing the hard drive & upgrading the RAM will breathe new life into it, most likely!
You do not need to shut it down each time you're done using it - in fact, I leave my MacBook asleep 90% of the time and reboot it every couple of weeks or when it seems to be getting a bit sluggish. I've been doing that for the last 7 years and she's still chugging along.
~Lyssa

I am facing 'How do you want to use this disc' whenever I read/open any lightscribe discs having data.

Hi,
When I insert a lightscribe DVD/CD into a lightscribe optical drive, then when I click to open the DVD, I faced this error 'How do you want to use this disc', although the DVD was full of data. When opening these
lightscribe DVD/CD via NON lightscribe optical drive, I noticed that the DVD/CD opened well without any problems at all.
Also, how can the System show to me 'How do you want to use this disc' , in particular when a DVD is non rewritable(DVD-R) and also contains data)?
Bear in mind, not all DVDs/CDs were not detected. However, only full lightscribe discs' (having data)
However, even blank lightscribe discs were detected without problems. When insert a lightscribe disc having data, then I faced that error. However, when inserting blank lightscribe discs I found that the disc were opened. Also,
non lightscribe discs were opened well.
When checking the device manager, I didn't see any issue with DVD/CD drive. If there were a problem unrecongnising, then I would have seen 'a remarkable mark' in front of it.
Note: I have faced this problem after trying formating a rewritable CD inserted onto the drive. Althouthg the format failed, all data on the disc was deleted. Anyway, after that, then inserting full-lightscribe discs are unregonised
Do you think the problem wth my optical drive. IF so, I would be saying why it wasn't happened with all other non lightscribe discs. If my lightscrib discs were corrupted, then why would they have opened well on another laptop.
I have done:
Press the Windows logo key+R to open the Run dialog box.
Type devmgmt.msc in the Run dialog box, then press Enter. If you are prompted for an administrator password or for a confirmation, type the password, or click Allow
In Device Manager, expand DVD/CD-ROM drives, right-click the CD and DVD devices, and then clickUninstall.
When you are prompted to confirm that you want to remove the device, click OK.
Restart the computer.
But the same prolbem is existing.
yes there is a virtual CloneDrive program installed on my PC, however, there is no any CD mounted into it. Even if a CD was mounted into Virtual Clondrive, there would be no problem at all, because the virtual CloneDrive is used to only
mount ISO disc images into it, and not physical discs.
Any I have do what you have said, when inserting a light-scribe disc having data, then I open it, I found this
NOTE: in the above screen shot there is a lightscribe DVD having data inserted. However, in the screen shot below, there a ightsrbe DVD not having data inserted. In the first screen shot, the disc is not reconginsed by Windows, however, in
the second is recognised.
Even when I have inserted a lightscribe disc not having data(empty), it opened well regardless of what virutal CloneDrive is enabled or disabled.
But when cliced on my problem didn't solve,
A man should convert his anger and sadness into strength to continue living in this life.

Hi,
The product Name of my computer is: HP Pavilion dv6-6093ex Entertainment
Notebook PC support
The number of my computer is : LM610EA#A2N.
Could anyone please at this splendid forum take some of their precious time
out to really reply my questions and solve my problems?
FIRST OF ALL:
My HP Pavilion Laptop is about 3 years old.
My
sister's Dell Inspiron laptop is 3 years old.
My HP lapotp is well-cared, as opposed to my sister's Inspiron Dell laptop,
which is always thrown in dust without caring at all. Also, its battery is
always inserted even when it is fully charged while the laptop is plugged in to
the main power supply.
However, my laptop is either used on only battery, or on plugin. Also, it is
kept from the dust.
But, I really found that the battery of the Dell laptop
still lasts about three and half hours, and there is no problem cooling fan is
not oproperly preporly.
I only remember one thing differently done on my laptop battery which is I
charged it fully, then I stored it without using it for about four months, then
when I reused it, I found it got worse over time. I.e. first time of using it
after storing,I found it empty, then I charged it again fully, however, then it
lasted about 2 hours, then 1 and half hours, next an hour, now it is only
lasting about 20 minutes without performance. If there is high performance, then
the computer shuts down suddenly.
My problem is follows:::
First: Whenever I inserted any Containing Data OR Data
CD/DVD-R LightScribe discs, I found that HP optical driver was
unable to read them. When clicking on the optical disc drive
'duble-click', then I find that disc opens as this way(NOT: With a CD/DVD player
is grayed out)
Blank Or Used CD, DVD±R,RW lightscirbe is unable to be
read:(clicking on it let it Open like a USB FlashDrive or With a CD,DVD player:
NOTE: with CD/DVD Player is grayed out)
Used CD/DVD±R/RW Non-LightScribe disc opens normal:
Blank CD,DVD±R,RW Non-LightScribe opens normal(Opens like a USB FlashDrive or
With a CD,DVD)::
My HP CD/DVD DVD±R/RW specis are::
Optical Drives
hp CDDVDW TS-L633R
Media Type DVD Writer
Name hp
CDDVDW TS-L633R
Availability Running/Full Power
Capabilities Random
Access, Supports Writing, Supports Removable Media
Read capabilities CD-R,
CD-RW, CD-ROM, DVD-RAM, DVD-ROM, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-R DL, DVD-RW
DL, DVD+R DL
Write capabilities CD-R, CD-RW, DVD-RAM, DVD-R, DVD-RW, DVD+R,
DVD+RW, DVD-R DL, DVD+R DL
Config Manager Error Code Device is working
properly
Config Manager User Config FALSE
Drive E:
Media Loaded
FALSE
SCSI Bus 0
SCSI Logical Unit 0
SCSI Port 0
SCSI Target Id
1
Status OK
Trying to solve the problem,
I have done these steps in order::
I tried checking with dignostic ulitiy:
I have tried Advanced View , this is the file of output data
diagnostic utility
LightScribe System Software Settings:
SOFTWARE\LightScribe\MessageDir
C:\Program Files (x86)\Common
Files\LightScribe\
SOFTWARE\LightScribe\LSPrintDialog C:\Program Files
(x86)\Common
Files\LightScribe\LSPrintDialog.exe
SOFTWARE\LightScribe\LSPrintingDialog
C:\Program Files (x86)\Common
Files\LightScribe\LSPrintingDialog.exe
SOFTWARE\LightScribe\LsPrintLauncher
C:\Program Files (x86)\Common
Files\LightScribe\LSPrintLauncher.dll
SOFTWARE\LightScribe\ResourceDir
C:\Program Files (x86)\Common
Files\LightScribe\res
SOFTWARE\LightScribe\LSPrintAPI C:\Program Files
(x86)\Common
Files\LightScribe\LSPrintAPI.dll
SOFTWARE\LightScribe\Update\UpdateShellCommand
http://www.lightscribe.com/go/downloads/windows
SOFTWARE\LightScribe\Update\PreviousVersion
1.18.20.1
SOFTWARE\LightScribe\Update\CurrentVersion
1.18.27.10
SOFTWARE\LightScribe\Update\TrailingVersion
SYSTEM\CurrentControlSet\Services\LightScribeService\Type
16
SYSTEM\CurrentControlSet\Services\LightScribeService\Start
2
SYSTEM\CurrentControlSet\Services\LightScribeService\ErrorControl
0
SYSTEM\CurrentControlSet\Services\LightScribeService\
SYSTEM\CurrentControlSet\Services\LightScribeService\DisplayName
LightScribeService Direct Disc Labeling
Service
SYSTEM\CurrentControlSet\Services\LightScribeService\ObjectName
LocalSystem
SYSTEM\CurrentControlSet\Services\LightScribeService\Description
Used by the LightScribe software components to support 3rd party disc labeling
applications using the LightScribe COM Application Programming Interface
(LSCAPI). This service needs to run for LightScribe direct disc labeling to
work.
SYSTEM\CurrentControlSet\Services\Eventlog\Application\LightScribeService\
SYSTEM\CurrentControlSet\Services\Eventlog\Application\LightScribeService\
SYSTEM\CurrentControlSet\Services\Eventlog\Application\LightScribeService\TypesSupported
7
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\0
IDE\CdRomhp_CDDVDW_TS-L633R______________________0300____\4&334f7860&0&0.1.0
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\Count
2
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\NextInstance
2
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\1
SCSI\CdRom&Ven_ELBY&Prod_CLONEDRIVE&Rev_1.4\1&2afd7d61&0&000000
SOFTWARE\Microsoft\Windows
NT\CurrentVersion\Winlogon\allocatecdroms
0
SYSTEM\CurrentControlSet\Services\CDRom\autorun 1
SOFTWARE\INTEL\Intel
Application Accelerator Not detected
Drives and Media:
Drive 0 : hp CDDVDW TS-L633R 0300 219 (E, Media
Imaging Parameter : 114
I tried running the below command line to fix potential disk issue 'Chkdsk
/r /f'
I cleaned the drive, discs, and so on.
I have uninstalled the all third-party data recording software.
I have uninstalled the Cyber DVD suite, lightscribe system software which
came pre-installed with my HP pavilion Notebook.
I have recovered my system from the Factory Recovery discs.
I have tried opening all those LightScibe discs not opening on my HP optical
drive, on a Dell optical drive, and all of them were opened well, although Dell
optical drive did not have a lightscribe feature at all., nor third party disc
recording software
However, the problem is still with opening the discs LIGHT-SCRIBE
Thus, my questions are:
How to determine if the drive is corrupted and needs to be replaced with
another one.
I think there something needed to be done on the BIOS Of my HP
laptop[[[A similar problems happened on my Desktop computer's optical
drive which is as follows:::(ALL discs are opened as empty by Optical Drive of
My Desktop Computer) ---while my optical drive of my desktop was connected to
the primary slave IDE, and the HDD was connected to the
primary master IDE, the optical drive and hard disk are functioning
well. However, I remember that while burning an image with Nero essential V: 5,
something went wrong, and then the Optical Drive of My Desktop Computer
(HL-DT-ST DVD-RAM GH22NP20) became NOT recognised/Installed on
BIOS, although it was still shown on the device manager as a
recognised device. Also, it was listed on my computer, however, when entering a
disc(blank or with data) into the drive, I found it was not recognised, and it
opened empty(no files at it), although it contains data. Thus, I decided to boot
to BIOS, and clicked on 'Autodetection for IDE', then I found that only HDD was
still shown as installed on BIOS. However, the optical drive was not. Th I tried
clicking on it on BIOS and then clicking on 'enter' to try to let the device be
re-recognized. However, that made no difference. I had to take part my computer
,and then reconnected the optical drive onto the secondary slave
IDE , and let HDD connected to the same primary master IDE.
Then, I found that the problem solved and all discs became being read
normally. Aslo, optical drive became installed on BIOS]]]
What is meant with with double Layer Support.
How much does it cost?
A man should convert his anger and sadness into strength to continue living in this life.

How do you change an used ipad to a new user with a new itunes account?

How do you cange a used ipad to a new user with a new itunes account?

plug your ipad to your computer, open your itunes, click on the ipad icon, at the first page there is an option to "restore" ipad to its factory settings, click it. Don't remove USB connection, wait until it finishes wiping the data and it should place a new window that asks you to register the ipad.
There you go, your iPad is sync with your itunes account under your name, its best to also use "Find my iPad" just in case it gets lost, you can track it from your computer. Very handy tool and its free!
But if you want the data that is in the iPad, back up it first and sync the content to your library before restoring it to its factory settings
Have a great day and enjoy your iPad

What yo do when itunes says you have not used itunes before please check review

what do you do when itunes says you have not used itunes before so click review. trying to add apps to my ipod touch 2

Create a iTune and App Store account without credit card
1. Go to App Store and select a free app
2. Tap INSTALL APP
3. Create New Apple ID
4. Confirm Your Country
5. Agree with Terms and Conditions
6. Fill in your Apple ID and Password (must be a valid email address)
7. Create and answer your secret question e.g. What is the name of my dog?
8. Select NONE for Billing Information (see picture below)
9. Fill in Billing Address i.e. your address
10. Submit application for new Apple ID
11. Wait for verification email
12. When email arrive, verify your account
13. Start downloading your free apps
http://i1224.photobucket.com/albums/ee374/Diavonex/6f6e54ff.jpg

How do you whiten teeth using iPhoto tools?

How do you whiten teeth using iPhoto tools?

You need more powerful editing software for that - iPhoto is good but basic
PhotoShop Elements is a good value - Gimp is open source and free - there are many others
LN

How do you download InDesign using the Adobe Download Manager?

How do you download InDesign using the Adobe Download Manager?

With the Adobe Download Assistant installed you should be able to initiate the download at http://www.adobe.com/cfusion/tdrc/index.cfm?product=indesign. If this is not working for you then please try an alternate web browser.

Re: How do I leave my email on the email server using iPad 2 .

Re: How do I leave my email on the email server using iPad 2 .
The iPad 2 wipes the messages off the server when downloading...
This option is not in advance settings for other email providers.

You have to actually have another email account with a email provider. Whether that is your ISP or one of the free/paid email providers like Gmail, Yahoo, MS Outlook.

I would like to leave my iMac on Snow Leapord to use Power PC software, and run Mountain Lion on my Macbook pro. I am getting an iPhone 5. Is there a way to use mail on all of them?

I would like to leave my iMac on Snow Leapord to use Power PC software, and run Mountain Lion on my Macbook pro. I am getting an iPhone 5. Is there a way to use mail on all of them with the same accounts?

Any IMAP e-mail account can be accessed from all devices just fine. You don't need to upgrade from Snow Leopard to be able to access an IMAP e-mail account. However, Snow Leopard won't have built-in support for iCloud. As mende1 points out, you can still read your iCloud e-mail from Snow Leopard, but you have to set it up manually. You won't be able to do things like sync your iCloud calendar or addresses with iCal or Address Book on the iMac, though.

How do you leave your iMac when you're not using it?

Similar Messages

Maybe you are looking for