How do you Reset iPad to factory defaults

How do you reset an iPad to factory defaults?

Go into Recovery Mode per the instructions here.  You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again.  Also, if you have IOS-7, read this.

Similar Messages

  • After updating software on IPAD from computer says I have to reset IPAD to factory default and will lose all data???

    After updading software on IPAD2 tells me I have to reset to factory default and will lose all data

    Kinda.
    Read the following in its entirty before doing anything.
    Note that a "Restore" could take well over an hour!  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow the on-screen directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here.  You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again.  Also, if you have IOS-7, read this.

  • How do you reset ipad to erase all previous data entry including personal information?

    I have a new Ipad 2 and it does not recognize me, how can I reset everything back to zero and re-enter my personal data?

    Settings>General>Reset>Erase all content and settings

  • I have a P2035 that is stuck on MANUAL for IP configuration, how can I reset this to factory default

    The ip address is set to 0.0.0.0 and I cannot connect to it at all to get to the webportal to reset or change, is there any way to reset to factory default?

    Our process would involve the original owner taking or shipping the phone to a technician to be unlocked. However, since it is out of the warranty period, there may be a cost depending on your location. Call us: http://www.sonyericsson.com/cws/corporate/common/contact/phonelist
    Others may suggest other options, but of course, we would not reccomend these.

  • How do you reset phone to factory settings?

    I need to send my old phone in to verizon and I want to remove all my personal stuff. how do I do a hard reset of the phone?

        cw3macke,
    Great question. I know how important it is to remove all of your information from the device before sending it out. I have a great link that will provide you with the steps on how to complete the Factory Reset on the Droid Razr: http://vz.to/1dmLx4r Please keep us posted if you have any further questions or concerns.
    KevinR_VZW
    Follow us on Twitter @VZWSupport 

  • How can you reset your Photoshop version default in Bridge CS5?

    After installing Photoshop CS6 , I have decided my workflow is much better in CS5, but cannot get Bridge to acknowledge Photoshop CS5 with keyboard commands [ex. command O] after deinstalling Photoshop CS6.
    I assumed this would have been a Preferences option but it is not.
    Please tell me this can be done.
    Personally, I find CS6 really slow, specifically with keyboard functions. CS5 would allow you to cue several tasks while it's working on present task. CS6 won't even let you close a file [command W] in mid-save...

    Oops.
    Hadn't restarted Bridge CS5 since deinstalling CS6. Now it's opening files in Photoshop CS5.

  • I can not reset my ipad to factory default. Any help appreciated

    I have taken over my dads ipad, but cannot download any apps as he cannot remember his apple id password.
    I have tried to reset ipad to factory default with no luck

    Read this:
    http://support.apple.com/kb/HT5818

  • HT4060 tried everything and can't get my ipad to charge...how do you reset it if battery is complety dead?

    tried everything and can't get my ipad to charge.  How do you reset IPad when battery is completly dead?  charger and cable works fine on IPhone.

    First make sure you are using the charger that came with your iPad and plug that into a known good wall outlet. Let your iPad remain on the charger for at least an hour. It may take that long before it responds if the battery is completely dead. If using the charger that came with your iPad there are several reasons it may fail to charge.
    Bad outlet. Make sure the Utsler has power.
    Bad charger. Try a different charger.
    Bad cable. Try a different cable.
    Dirt in the connector. Check and clean if necessary.
    Hardware failure. Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

  • How do you reset an ipad mini without knowing the password?

    I have just recently changed my password, but know i have forgot the new one. How do you reset the ipad without knowing the password?

    If you mean the passcode to unlock the iPad then you will need to connect it to the computer that you normally sync to and you should then be able to reset the iPad and restore/re-sync your content to it (http://support.apple.com/kb/HT1212) - you may need to put the iPad into recovery mode in order to be able to reset it : http://support.apple.com/kb/ht1808
    If you do it via a different computer then :
    If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.

  • How do you reset an i pad to factory settings?

    How do you reset an i pad to factory settings?

    strines wrote:
    Do you think this will resolve a problem I have which is that I can't send e mails anymore using outlook.com on my i pad?
    No, you can try Reset and see if that helps.
    http://support.apple.com/en-us/HT201559

  • HT1338 With original installation cd missing, how do you reset OSX 10.6.8 (originally OSX 10.5) to factory settings??

    With the original installation cd missing, how do you reset a computer (with OSX 10.5 upgraded to OSX 10.6.8) to its default settings?

    benfromnv wrote:
    With the original installation cd missing, how do you reset a computer (with OSX 10.5 upgraded to OSX 10.6.8) to its default settings?
    The machine came with 10.5, those disks are not available anymore from Apple.
    You use the $29 10.6.3 white retail disks you get from Apple store online or already have in your possession.
    Yes you upgraded OS X 10.5 to 10.6.3 with them, it also contains the entire 10.6.3.
    When you "upgraded" your Applications and User accounts folders remained while only OS X 10.5 folders was replaced with 10.6.3 folders.
    So if you hold the c or option key down while booting from the 10.6.3 disks, you can use Disk Utility to erase the entire drive and reinstall 10.6.3 only, like a brand new machine.
    How to erase and install Snow Leopard 10.6

  • HT201304 how do you reset a forgotten restrictions passcode?

    how do you reset a forgotten restrictions password?

    Uness you have a backup that was made before you added the Restrictions passcode, you have to restore to factory defaults/new iPod.  If the backup contains the Restriction passcode, it will be restored.

  • Grandaughter has locked i pad 2 with passcode and then forgotten number how do you reset i pad to get it to work again

    grandaughter has locked i pad 2 with passcode and then forgotten number how do you reset i pad to get it to work again

    If You Are Locked Out Or Have Forgotten Your Passcode or Just Need to Restore Your Device
      1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
      2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
      3. iOS- Understanding passcodes
         If you have forgotten your Restrictions code, then follow the instructions
         below but DO NOT restore any previous backup. If you do then you will
         simply be restoring the old Restrictions code you have forgotten. This
         same warning applies if you need to restore a clean system.
    A Complete Guide to Restore or Recover Your iDevice (if You Forget Your Passcode)
    If you need to restore your device or ff you cannot remember the passcode, then you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and re-sync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
    Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
    Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
    Follow these steps to restore your device:
         1. Verify that you are using the latest version of iTunes before attempting to update.
         2. Connect your device to your computer.
         3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
         4. Select the Summary tab.
         5. Select the Restore option.
         6. When prompted to back up your settings before restoring, select the Back Up
             option (see in the image below). If you have just backed up the device, it is not
             necessary to create another.
         7. Select the Restore option when iTunes prompts you (as long as you've backed up,
             you should not have to worry about restoring your iOS device).
         8. When the restore process has completed, the device restarts and displays the Apple
             logo while starting up:
               After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
              to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
              iOS, keep your device connected until the "Connect to iTunes" screen goes away or
              you see "iPhone is activated."
         9. The final step is to restore your device from a previous backup. If you do not have a
              backup to restore, then restore as New.
    If you are restoring to fix a forgotten Restrictions Code or as a New device, then skip Step 9 and restore as New.

  • HT201304 If I forgot my password is there any way to remove the restrictions and backup my iPod from the computer? I tried reseting it to factory defaults and then backing it up but it still has the restrictions on.

    I'm trying to remove my restrictions, and i reset it to factory default, but everytime i back it up the restrictions are still on. I don't want to have to register as a new ipod and loose everything i've bought and added.

    - Restore from a backup that was make before you added the Restrictions passcode. If you restore from a backup made with the Restrictions passcode the Restrictions passcode is also restored.
    - Restore to factory settings/new iPod.
    - If you are up to it see:
    How to reset forgotten Restrictions...: Apple Support Communities
    How to reset forgotten Restrictions...: Apple Support Communities

  • I am selling my 5S I phone and need to wipe all my data off it. How do I reset it to factory settings and make sure all my data is errased

    I am selling my 5S    I phone and need to wipe all my data off it. How do I reset it to factory settings and make sure all my data is errased

    Here's what you do: What to do before selling or giving away your iPhone, iPad, or iPod touch

Maybe you are looking for

  • How to Create a Validation based on a Z table

    I want to create a validation for t-code FB50 so that for any line item that contains a GL Account listed in a table, the validation would then check to see if the field Trading Partner is populated. My question is How do I set up the validation so t

  • Checks on cash flow report

    Hi ,       When I using cash flow report and have been issued and received a lot of checks, but I cannot seen those at security level - "checks". Why? All of those are belongs to "Cash accounts". Could anyone give me a explanation or example? Thanks

  • Change database name - Crystal10 and Visual Studio 2005

    <p>Hi there,</p> <p> I have about 150 crystal reports in my development environment. I need to move them into the testing environment. Every environment has its own database and every database is names '[client name]_[environment]' so I get things li

  • Could not start the listener with a domain user

    Hi all, I am working on Windows 2003 with Oracle 10.2.0.2 ! With user "local system account", I can start the listener and I have no problems! after chaning the user that runs the listener from local system account to a domain user, I cannot start th

  • I can't listen the music in my iPhone

    I found that I can't listen music in my IPhone neither to listen the videos in YouTube. When I try to use it in Ipod mode, the only options to listen to the music are connector dock and AirPort express. If I plug in the headphones goes to headphones