How do you turn ipod from disk mode to normal?

a few days ago i turned my ipod to disk mode. now i need to turn it back into the original way, but itunes doesnt even let me see the ipod anymore because its disk mode i think. somebody plzz hellp!

Do a Reset please
http://docs.info.apple.com/article.html?artnum=61705

Similar Messages

  • TS1463 What is the easiest way to restore my ipod back to factory specs. It has a red circle with a red x in the middle,please help me to fix my ipod, until now i can't use my ipod..i tried all the procedures in Restore ipod from disk mode but still not w

    What is the easiest way to restore my ipod back to factory specs. It has a red circle with a red x in the middle,please help me to fix my ipod, until now i can't use my ipod..i tried all the procedures in Restore ipod from disk mode but still not working, please help me...

    If you are unable to get the iPod into Disk Mode to try and restore it, it's a very good indication, as mentioned in the article, that the iPod's hard drive is damaged and in need of replacement either by Apple or a third party repair company.
    B-rock

  • How do you turn off power saving mode on a Officejet 6000

    I have 5 Officejet 6000 printer contected by using the ethernet port. They print fine when not in power saving mode. When they go into power saving mode and a print job is sent to them, they do not print. You have to power off and on the printer for the job to print. I need to turn off the power saving mode on these printers. Computers sending print jobs are XP and Window 7.

    I am not aware of a way to turn that feature off completely since it does not have a front panel.
    However, I suspect largely that the issue is with DHCP IP (automatic) settings.  Printers in general, with some routers, have issues with DHCP and standby where they no longer communicate using DHCP information.
    I recommend setting static IP addresses for any printer on a network as it prevents most network issues with printers from occuring.  
    Print a network configuration page by holding the network button for 3 seconds and then releasing it.  A printout should be printed with the printers IP address.
    Once that is done, enter that IP address into the browser on a computer as if you were going to a site.  Once that is entered, go to that site and the printer status page should be loaded.
    There should be a Network option at the top.  Select that option.
    On this page, somewhere on the left, there should be an IPv4 option in a wired section.  Select this and it will give the option for automatic or manual IP setup.
    Select Manual IP setup.  Enter The IP address and subnet mask from the printout.  You can enter the gateway and the DNS servers, but they aren't really used since this printer does not have any web functions.
    Click apply and you should get a success message.
    At this point, the printer should have a static IP address and the issue of it not responding after entering standby should no longer be present.  
    PrintDoc's post has similar steps for a wireless version of the same printer.  The only step that would really be different is choosing Wired instead of Wireless on the setup page.
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • How do you start up from disk

    My 2007 iMac has become very sluggish.  The little colorful round ball justs spins and spins so much now.  I went to Disk Utility and for the first time selected verify disk.  Part way through the verification I got an error message telling me "The volume Macintosh HD was found corrupt and needs to be repaired.", "Error: this disk needs to be repaired.  Start up y...isc), and then use Disk Utility to repair this disk."  The problem apparently comes from "invalid volume file count" and "invalid volume directory count".
    I am sure this is a simple task for most but I am unsure how to proceed.  I have my original OS X Leopard disk and my upgraded OS X Snow Leopard disc. Any direction in how to proceed would be greatly appreciated.

    Before you do ANYTHING make sure you have a good a backup. I see you have a Time Capsule to check to see if your backup is OK.
    Next Insert the original Leopard Install disk in the Superdrive. Restart, when you hear the startup tone hold down the Option key and choose the Install Disk. Select the language then click the Utilities Menu and choose Disk Utility. Run Repair Disk from there, you will need to run Repair Disk multiple times until no errors are found. If you continue to get errors take the machine into an Apple Store or AASP to have the HD replaced. Make sure you let them know  you have been backing up on Time Capsule and want to restore your backup from there.

  • How do you turn off the fax mode after you have faxed

    I SET UP MY PRINTER TO FAX TODAY AND NOW MY PHONE AND FAX ARE STILL IN THE FAX MODE

    What printer are you using for this? Also what exactly do you mean by turning off fax mode?
    Jon-W
    I work on behalf of HP
    Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
    Click the KUDOS STAR on the left to say “Thanks” for helping!

  • I have a ipod nano 4G, and to sync my music, i have to put my ipod in disk mode. but when i try to turn it on regularly, it gets stuck on the apple logo screen. any idea how to keep it from getting stuck?

    i have a ipod nano 4G, and to sync my music, i have to put my ipod in disk mode. but when i try to turn it on regularly, it gets stuck on the apple logo screen. any idea how to keep it from getting stuck?

    Did you also check under Albums?  All Songs?
    iPod Nano 5th Gen. User Manual

  • TS1463 how do you put the ipod into disk mode

    how do you put the ipod into disk mode

    iPod nano (7th generation)
    Before placing the iPod into Disk Mode, verify that it has a charge.
    Reset the device by pressing the Sleep and Home buttons simultaneously until the display turns black. This should take about eight seconds.
    When the display turns black, press and hold the Volume Down and Volume Up buttons simultaneously until the device enters Disk Mode.
    iPod nano (6th generation)
    Before placing the iPod into Disk Mode, verify that it has a charge.
    Reset the device by pressing the Sleep and Volume Down buttons simultaneously until the display turns black. This should take about eight seconds.
    When the display turns black, hold down the Volume Down and Volume Up buttons simultaneously until the device enters Disk Mode.
    iPod devices with a Click Wheel
    If necessary, verify that your iPod has a Click Wheel.
    Before placing the iPod into Disk Mode, verify that it is charged.
    Toggle the Hold switch on and off (set it to Hold, then turn it off again.)
    Press and hold the Menu and Select buttons for at least six seconds, until the Apple logo appears.
    When the Apple logo appears, release the Menu and Select buttons and immediately press and hold the Select and the Play/Pause buttons until the Disk Mode screen appears.
    Connect the iPod to your computer; the screen on the iPod will should say "Do not disconnect".
    If you are having difficulty putting your iPod into Disk Mode, set it on a flat surface. Make sure that the finger pressing the Select button is not touching the Click Wheel. Also make sure that you are pressing the Play/Pause button toward the outside of the Click Wheel and not near the center. If you are still unable to put your iPod into Disk Mode, use one finger from one hand to press the Select button, and one finger from the other hand to press the Play/Pause button.
    Older iPod models without a Click Wheel
    Before placing the iPod into Disk Mode, verify that it has a charge.
    Toggle the Hold switch on and off (set it to Hold, then turn it off again.)
    Press and hold the Play/Pause and Menu buttons until the Apple/iPod logo appears, then release them. This resets iPod. When you reset iPod, all your music and data files are saved, but some customized settings may be lost.
    When the Apple logo appears, immediately press and hold the Previous and Next buttons until the Disk Mode screen appears.
    Connect the iPod to your computer; the screen on the iPod should say "Do not disconnect".
    source: Putting iPod into Disk Mode

  • TS1363 how can i change from disk modae to normal mode as none of the buttons seems to be working ?

    how can i change from disk modae to normal mode as none of the buttons seems to be working ?

    Have you tried a hard reset of the iPod yet?
    How to reset iPod
    This should take you out of disk mode and allow the iPod to boot up as it normally does.
    B-rock

  • How do i turn off the compatibility mode on my ipod classic

    how do i turn off the compatibility mode on my laptop, i cannot transfer music from the laptop to my ipod classic, it shows a warning massage that i shoud turn off the compatability mode.

    Reset it: hold the Menu and center buttons down until it resets.
    If that does not work you may just have to run the battery down.

  • How do you transfer content from an iPod touch to iTunes?

       How do you transfer content from an ipod touch to itunes without buying another software?

    You can't.  Mobile devices are not set up to transfer most items to a computer and if that's what you want to do (with the noted exception) then you have to pay for it.
    Some of the information below has subsequently been summarized and duplicated by turingtest2 in the document: Recovering your iTunes library from your iPod or iOS device - https://discussions.apple.com/docs/DOC-3991
    Your i-device was not designed for unique storage of your media. It is not a backup device and media transfer was designed for you maintaining a master copy of your media on a computer which is itself properly backed up against loss. Syncing is one way, computer to device, updating the device content to the content on the computer, not updating or restoring content on a computer. The exception is iTunes Store purchased content.
    iTunes Store: Transferring purchases from your iOS device or iPod to a computer - http://support.apple.com/kb/HT1848 - only media purchased from iTunes Store
    For transferring other items from an i-device to a computer you will have to use third party commercial software. Examples (check the web for others; this is not an exhaustive listing, nor do I have any idea if they are any good):
    - Senuti - http://www.fadingred.com/senuti/
    - Phoneview - http://www.ecamm.com/mac/phoneview/
    - MusicRescue - http://www.kennettnet.co.uk/products/musicrescue/
    - Sharepod (free) - http://download.cnet.com/SharePod/3000-2141_4-10794489.html?tag=mncol;2 - Windows
    - Snowfox/iMedia - http://www.mac-videoconverter.com/imedia-transfer-mac.html - Mac & PC
    - iexplorer (free) - http://www.macroplant.com/iexplorer/ - Mac&PC
    - Yamipod (free) - http://www.yamipod.com/main/modules/downloads/ - PC, Linux, Mac [Still updated for use on newer devices? No edits to site since 2010.]
    - 2010 Post by Zevoneer: iPod media recovery options - https://discussions.apple.com/message/11624224 - this is an older post and many of the links are also for old posts, so bear this in mind when reading them.
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive - https://discussions.apple.com/docs/DOC-3141 - dates from 2008 and some outdated information now.
    Copying Content from your iPod to your Computer - The Definitive Guide - http://www.ilounge.com/index.php/articles/comments/copying-music-from-ipod-to-co mputer/ - Information about use in disk mode pertains only to older model iPods.
    Get Your Music Off of Your iPod - http://howto.wired.com/wiki/Get_Your_Music_Off_of_Your_iPod - I am not sure but this may only work with some models and not newer Touch, iPhone, or iPad.
    Additional information here https://discussions.apple.com/message/18324797

  • HOW DO YOU TURN OFF "FIREFOX PREVENTED THIS PAGE FROM AUTOMATICALLY RELOADING". I did the "see Advanced - General - Accessiblity. and still having problems

    HOW DO YOU TURN OFF "FIREFOX PREVENTED THIS PAGE FROM AUTOMATICALLY RELOADING". I did perform the "see Advanced - General - Accessibility. It worked for me and my "user" site (don't know how to say my site) and still having problems with my wife's. I have gone to OPTIONS → GONE TO → ADVANCE and CLICKED THE LINE → ""Warn me when websites try to redirect or reload the page…""
    This did not rememdy the problem. I did try to get on the other site suggested
    http://kb.mozillazine.org/Accessibility.blockautorefresh
    but got a 404 error...
    I have googled the "ff prevented...." and after a number of hours searching I still have not found a fix...
    REALLY HOPE SOMEONE CAN HELP ME....
    JM

    You should still disable this setting:
    *Firefox > Options/Preferences > Advanced > General : Accessibility : [ ] "Warn me when web sites try to redirect or reload the page"
    The setting in "Options > Advanced > General" is meant as an accessibility feature, as you can see by the label of that section, so that people with disabilities or people who use screen readers do not get confused and is not meant as a safety protection to stop redirecting.
    What is the value of the <b>accessibility.blockautorefresh</b> pref on the <b>about:config</b> page?
    *http://kb.mozillazine.org/accessibility.blockautorefresh
    If you have problems with preferences, see:
    *http://kb.mozillazine.org/Preferences_not_saved
    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
    *Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
    *Do NOT click the Reset button on the Safe Mode start window
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

  • How can you transfer data from one ipod to another ?

    How can you transfer data from one ipod to another ipod ?

    The geniusbar told me what to do, I understood but there is still a problem for me >:/ It's not showing up though. Like "device."  Nothing is happening, and I tried as soon as I got home. Then after half an hour, then an hour, then 3 hours. My problem is that it's not showing up! It's stuck in recovery mode! There's still like 25% battery. So I have no idea why.

  • How do you turn your music off on your ipod touch?

    how do you turn your music off on your ipod touch?

    Double click the Home button (fro a lock-screen) and the music control sill show. Tap the pause icon (two verticle parallel lines). The same from the Music app.

  • How do you choose songs from your ipod instead of from the car dashboard while your ipod is plugged into your car?

    How do you choose songs from your ipod instead of from the car dashboard while your ipod is plugged into your car?

    It depends on your car stereo. On the JVC we have you can select either "Head Mode" or "iPod Mode" when you're plugged into the USB port. Ipod Mode lets you select the songs from the iPod although the radio still controls the volume. I believe the Alpine I have does the same thing.

  • HT1386 How do you download music from a disc to you iPod?

    How can you download music from a disc to your iPod?

    Turn on computer.
    Open itunes.
    Insert cd.
    Import cd.
    Connect ipod.
    Select what you want
    Sync

Maybe you are looking for