How Does EAX For Games W

I am afraid that I've never been able to figure out how to configure my EAX Console to ensure that the EAX is working in my gaqmes. For example, in Far Cry, you can enable hardware mixing and, after that, EAX 2. If I enable these, what do I set in the EAX Console? Enable Audio Effects? If so, what audio effect? You use to be able to select EAX Games under special effects, but that option isn't there unless I import it.
How do I tell what game uses what setting? Other games I want to ensure I have the proper setup for are Half Life 2, Call Of Duty, Medal of Honor, Halo.
Clarification of the exact procedure would be most welcome.

Foomobile,
For games, with this card, you don't need to set anything up except EAX in the game itself. Just choose an EAX option in the game and that's all you need to do. You don't need to adjust anything in EAX console.
You may want to update to the latest drivers aswell, as they add extra EAX support (EAX 4.0).
Cat

Similar Messages

I live in the country and there is no High speed available, How does Firefox for desk top work with Dial up ???

I live in the country and there is no High speed available, How does Firefox for desk top work with Dial up ??? I have a great dell computer, Dimention 8400. Before I install firefox I want to know for no waste of time for either party..

Unless you enabled Find My iPad on it before it was stolen then there isn't any way to locate it. If you did enable it then you could try locating it either via http://icloud.com on a computer or Find My iPhone on another device - but that will only work if it's connected to a network and the device hasn't already been wiped and/or Find My iPad disabled on it.
If it was stolen then you should report it to the police. You should also change your iTunes account password, your email account passwords, and any passwords that you'd stored on websites/emails/notes etc.
If it was never registered to your account then it won't appear on your support profile : https://supportprofile.apple.com/
The only other ways to find it that I know of (apart from on the actual device) are via the packaging, the backup on a computer's iTunes : http://support.apple.com/kb/HT4061

Curious: How does "Save for Web" reduce the file size?

I do know HOW TO USE "Save for web" -- no questions there. I'm wanting to understand better what's going on under the hood.
When I start with say, an 8x10 JPG at 300 dpi, I understand completely how bringing that down to 72 dpi yields a much smaller file. Simple math.
What I don't understand is how the "Save for Web" function can reduce that smaller file size so drastically at the same dimensions, still 72dpi, with negligible image loss (at least at the 80% quality). Maybe it's just my amateur eyes, but for everyday casual web pages, I can discern no significant difference between the two 72dpi images. (At lower quality settings, I do see differences.)
Can anyone explain a bit more of HOW Photoshop does this? Is it simply compression? For example, is it -roughly- analogous to converting an AIF sound file as an MP3?
Thanks,
cb

Thanks, that worked. I figure there was a setting in there somewhere and was even in the right tab, but didnt think to click on that.

How does upgrade for aperture work if use the trial to download?

I have a new macbook pro. I have installed my Aperture 2.X on it. Can I download the trial and when I purchase get the "upgrade" price? If so, how does that work. Do I type in my 2.x serial number at some point?
Or, if I purchase the Aperture disk, how does the upgrade work then?

In either case, with AP 2.x installed, the AP 3 upgrade installer should see that and only require entry of the upgrade serial number.
If doing a clean install with AP 2 not installed, you enter the AP 3 upgrade serial number and will get a second serial number field pop-up asking for a full version serial number (you would enter the AP 2 serial number at this point).
Assuming nothing is amiss with your system, that should do it.

How create timer for game?

I want to know how much time player spend in the game.
For this i want create a timer.
I thing it must be something like this:
player come to the game (time 0:00), player plaing for example 22 minutes, gameover game (player spend 22 minutes and 0 sec).
code:
import flash.utils.getTimer;
var gameStartTime:uint;
var gameTime:uint;
var gameTimeField:TextField;
function mainFunction():void
     gameTimeField = new TextField();
     addChild(gameTimeField);
     gameStartTime=getTimer();
     gameTime=0;
     addEventListener(Event.ENTER_FRAME,showTime);
function showTime(event:Event)
     gameTime=getTimer()-gameStartTime;
     gameTimeField.text="You plaing: "+clockTime(gameTime)+"min";
function clockTime(ms:int)
     var seconds:int=Math.floor(ms/1000);
     var minutes:int=Math.floor(seconds/60);
     seconds-=minutes*60;
     var timeString:String=minutes+":"+String(seconds+100).substr(1,2);
     return timeString;
mainFunction();
Is this correct way?
If you know how to make code smaller can you please share?
Maybe exist standart component or something else for this?
Thank you.

Thank you guys!
Just asking how to make timer correct:)
I thout maybe you know existing standart coder or standart component for it?
For example i use the same timer for 5 games.. and for every game i need create code.. Is it possible to make code just one time and create something like standart components in Flash IDE ? Or maybe adobe have place where everyone can create components and share whit other? Or its all not possible, and need create the same code again?
By the way why i dont see my secons here?:
var gameStartTime:uint;
var gameTime:uint;
function mainFunction():void
     gameStartTime=getTimer();
     gameTime=0;
     addEventListener(Event.ENTER_FRAME,showTime);
function showTime(event:Event)
     gameTime=getTimer()-gameStartTime;
     myText.text="Time: "+clockTime(gameTime);
function clockTime(ms:int)
     var seconds:int=Math.floor(ms/1000);
     var timeString:String=String(seconds+100).substr(1,2);
mainFunction();

How does searching for tags in different languages work?

I have a website in English an German (and eventually also in French and Italian) to which I would like to assign the tag Lawyer (English) / Anwalt (German). Therefore I have set up the tag in the UI as below and tagged the page manually to try if it works. Everything works well, but when I search for the tag I can only find the pages by typing in the tag name (here lawyer), but I would also like to find it by typing in Anwalt. Is there a possibility to make the tags searchable in all languages except for creating a new tag for each language?
How do I have to put it here etc/tags/marketing:lawyer? Do I have to translate the tags first in the UI? I assume, that if I put etc/tags/marketing:anwalt, a new tag is created.
Thanks for your help!

What do you mean by "etc/tags/marketing:lawyer" - where do you put this? Such strings are not expected to work.
There are tag ids, which are based on the node names of the tag and which are not localized. In this case it would be "marketing:lawyer" or /etc/tags/marketing/lawyer (absolute paths work as well, albeit they are not written by the built-in tagging code). These would be used in the GQL search query in the normal search field in the content finder, using "tags:<tagid>", for example: "tags:marketing:interest/business"
Then there are titles, which you see in the tag labels when setting tags e.g. on a page, such as "Marketing : Lawyer", or "Marketing : Category / Subcategory" for nested tags. Titles are localizeable. If you have the suggestions enabled in the cf, you'd type e.g. "Lawyer" (user language set to English) or "Anwalt" (user language set to German), see a list of suggested items, select the tag (recognizable by icon) and the search field should be populated with "tags:marketing/lawyer" automatically.
See also
http://dev.day.com/docs/en/cq/current/wcm/tag_admin.html#Managing%20Tags%20in%20Different% 20Languages
http://dev.day.com/docs/en/cq/current/developing/tagging.html

How is it for games using Visa 64?

I am thinking of getting a MBP 15" and the GPU (9600) is less than some windows only laptops (9800 nVidia 1gig)
Fallout 3, Medal of Honor, ect..
Thanks

Heya, I'm currently gaming on the MBP (Late 2008) with the 256mb of GFX memory model (but with 4gb of memory.)
It runs Fallout 3, Left 4 Dead, Age of Empires 3 and other games beautifully. You should get at least 30 fps for all games (that being high settings for most games.) The only bad part about gaming with the MBP is the fan, which is facing up, instead of being on the bottom. This causes the fan to reach insane speeds with any game. If you don't mind the sound then by any means get it. But if you want to get a dedicated gaming machine, stay away. If you want a cheap and really good (I mean better than "alienware"; alienware is a piece of carp), get a Sager notebook

How does the delta works for changes made to Sales Document

Hi Experts,
How does delta for 2LIS_11_VAITM for the changes made to Sales Order Header.....
Example:
If a sales order had 10 line items any changes at the item level are captured by 2LIS_11_VAITM
Could you please update me on how the changes made at Sale Order Header level like Change of contract Date...etc
Does those changes are captured by 2LIS_11_VAITM.......
Please update

Hi,
SAP written lots of programs inside the Extractor, so it is not possible to tell how it will work, so you goto RSA2 in ecc and give the datasource and click on display and see the Function module and debug it you will know.
Thanks
Reddy

How does select stmt with for all entries uses Indexes

Hello all,
I goes through a number of documents but still confused how does select for all entries uses indexes if fields are not in sequences. i got pretty much the same results if i take like two cases on Hr tables HRP1000 and HRP1001(with for all entries based upon hrp1000). Here is the sequence of index fields on hrp1001 (MANDT, OTYPE, OBJID, PLVAR, RSIGN, RELAT, ISTAT, PRIOX, BEGDA, ENDDA, VARYF, SEQNR). in second case objid field is in sequence as in defined Index but i dont see significant increase in field even though the number of records are around 30000. My question is does it make a differrence to use field sequence (same as in table indexes) in comparison to redundant field sequence (not same as defined in table indexes), secondly how we can ge tto know if table index is used in Select for entries query i tried Explain in ST05 but its not clear if it uses any index at all in hrp1001 read.
here is the sample code i use to get test results.
test case 1
REPORT zdemo_perf_select.
DATA: it_hrp1000 TYPE STANDARD TABLE OF hrp1000 WITH HEADER LINE.
DATA: it_hrp1001 TYPE STANDARD TABLE OF hrp1001 WITH HEADER LINE.
DATA: it_hrp1007 TYPE STANDARD TABLE OF hrp1007 WITH HEADER LINE.
DATA: it_pa0000 TYPE STANDARD TABLE OF pa0000 WITH HEADER LINE.
DATA: it_pa0001 TYPE STANDARD TABLE OF pa0001 WITH HEADER LINE.
DATA: it_pa0002 TYPE STANDARD TABLE OF pa0002 WITH HEADER LINE.
DATA: it_pa0105_10 TYPE STANDARD TABLE OF pa0105 WITH HEADER LINE.
DATA: it_pa0105_20 TYPE STANDARD TABLE OF pa0105 WITH HEADER LINE.
DATA: t1 TYPE timestampl,
      t2 TYPE timestampl,
      t3 TYPE timestampl
SELECT * FROM hrp1000 CLIENT SPECIFIED INTO TABLE it_hrp1000 bypassing buffer
            WHERE mandt EQ sy-mandt AND
                  plvar EQ '01' AND
                  otype EQ 'S'AND
                  istat EQ '1' AND
                  begda <= sy-datum AND
                  endda >= sy-datum AND
                  langu EQ 'EN'.
GET TIME STAMP FIELD t1.
SELECT * FROM hrp1001 CLIENT SPECIFIED INTO TABLE it_hrp1001 bypassing buffer
            FOR ALL ENTRIES IN it_hrp1000
             WHERE mandt EQ sy-mandt AND
                    otype EQ 'S' AND
*                    objid EQ it_hrp1000-objid and
                    plvar EQ '01' AND
                    rsign EQ 'B' AND
                    relat EQ '007' AND
                    istat EQ '1' AND
                    begda LT sy-datum AND
                    endda GT sy-datum and
                    sclas EQ 'C' and
                    objid EQ it_hrp1000-objid.
*                    %_hints mssqlnt 'INDEX(HRP1001~0)'.
*delete it_hrp1001 where sclas ne 'C'.
GET TIME STAMP FIELD t2.
t3 = t1 - t2.
WRITE: 'Time taken - ', t3.
test case 2
REPORT zdemo_perf_select.
DATA: it_hrp1000 TYPE STANDARD TABLE OF hrp1000 WITH HEADER LINE.
DATA: it_hrp1001 TYPE STANDARD TABLE OF hrp1001 WITH HEADER LINE.
DATA: it_hrp1007 TYPE STANDARD TABLE OF hrp1007 WITH HEADER LINE.
DATA: it_pa0000 TYPE STANDARD TABLE OF pa0000 WITH HEADER LINE.
DATA: it_pa0001 TYPE STANDARD TABLE OF pa0001 WITH HEADER LINE.
DATA: it_pa0002 TYPE STANDARD TABLE OF pa0002 WITH HEADER LINE.
DATA: it_pa0105_10 TYPE STANDARD TABLE OF pa0105 WITH HEADER LINE.
DATA: it_pa0105_20 TYPE STANDARD TABLE OF pa0105 WITH HEADER LINE.
DATA: t1 TYPE timestampl,
      t2 TYPE timestampl,
      t3 TYPE timestampl
SELECT * FROM hrp1000 CLIENT SPECIFIED INTO TABLE it_hrp1000 bypassing buffer
            WHERE mandt EQ sy-mandt AND
                  plvar EQ '01' AND
                  otype EQ 'S'AND
                  istat EQ '1' AND
                  begda <= sy-datum AND
                  endda >= sy-datum AND
                  langu EQ 'EN'.
GET TIME STAMP FIELD t1.
SELECT * FROM hrp1001 CLIENT SPECIFIED INTO TABLE it_hrp1001 bypassing buffer
            FOR ALL ENTRIES IN it_hrp1000
             WHERE mandt EQ sy-mandt AND
                    otype EQ 'S' AND
                    objid EQ it_hrp1000-objid and
                    plvar EQ '01' AND
                    rsign EQ 'B' AND
                    relat EQ '007' AND
                    istat EQ '1' AND
                    begda LT sy-datum AND
                    endda GT sy-datum and
                    sclas EQ 'C'." and
*                    objid EQ it_hrp1000-objid.
*                    %_hints mssqlnt 'INDEX(HRP1001~0)'.
*delete it_hrp1001 where sclas ne 'C'.
GET TIME STAMP FIELD t2.
t3 = t1 - t2.
WRITE: 'Time taken - ', t3.

Mani wrote:
Thank you for your answer, its very helpful but i am still nor sure how does parameter rsdb/max_blocking_factor affect records size.
Hi,
The blocking affects the size of the statement and the memory structures for returning the result.
So if your itab has 500 rows and your blocking is 5, the very same statement will be executed 100 times.
Nothing good or bad about this so far.
Assume, your average result for an inlist 5 statement is 25 records with an average size of 109 bytes.
You average result size will be 2725 byte plus overhead which will nearly perfectly fit into two 1500 byte ethernet frames.
Nothing to do in this case.
Assume your average result for an inlist 5 statement is 7 records with an average size of 67 bytes.
You average result size will be ~ 470 byte plus overhead which will only fill 1/3 of a 1500 byte ethernet frame.
In this case, setting the blocking to 12 ... 15 will give you 66% network transfer performance gain,
and reduces the number of calls to the DB by 50%, giving additional benefit.
Now this is an extreme example. The longer the average row length is, the lower will be the average loss in the network.
You have the same effects in memory structures, but on that layer you are fighting single micro seconds instead of
hundreds of these, so in real life it is rarely measurable.
Depending on table-statistics, oracle might decide for short inlists to use a concatanation instead of an inlist.
This is supposed to be more costy, but I never had a case where I could proove a big difference.
Values from 5 to 15 for blocking seem to be ok for me. If you have special statements in customer coding,
it #might# be benefitial to do the mentioned calculations and do some network tracing to see if you can squeeze your
network efficiency by tuning the blocking.
If you have jumbo frames enabled, it might be worth to be analyzed as well.
If you are only on a DB-CI system that is loopback connected to the DB, I doubt there might be a big outcome.
Hope this helps
Volker

How does S.T.A.L.K.E.R. use EAX natively in Vis

inside the stalker folder there are several sound files, they are named:
eax.dll
OpenAL32.dll
wrap_oal.dll
How does this work?

In more detail, OpenAL32.dll is a router which checks for available renderes:? "ct_oal.dll" is the nati've Creative driver, "wrap_oal.dll" is an OpenAL to DS3D wrapper for Windows XP and there is also a Software stereo renderer with EAX2 support in the same file. Under Vista, the router can only select a nati've driver or the software renderer. It defaults always to the nati've driver, unless the game requests something specific, which unfortunately a lot of developers do. You can also delete the "wrap_oal.dll" file from both the game folder and System32 to make sure it selects the nati've device.

I've change device Ipone4s to Ipnoe 5 . How to i get the old game for game center

I've change device Ipone4s to Ipnoe 5 . How to i get the old game for game center

Regarding the old iMac. Just delete your USER NAME from the Control Panel. Go into System Preferences - then User/Groups and delete your account from there.
Just a bit of advice though before you do all this, go and buy yourself a remote Hard Drive, they're really good value today and copy off all of your sacred files from your old computer onto the new drive. You could also do the same via the Backup.app
It's well worth doing.... You can easily delay the switch over for a few days and you'll then have a backup disc that you'll start to use again and again.

I can't register for Games Centre on iPhone 4. It says that every nickname is already in use (even the most ridiculous and obscure ones) Does anyone have a suggestion to correct this?

I have been trying to register for Games Centre on my iPhone 4. I have tried so many Nicknames (even obscure and ridiculous ones), and it tells me that every single Nickname is aleady in use by another user. Does anyone else have this problem? Any suggestions on how to overcome this? It would help if the Games Centre had a "Contact Us" tab.

Not using any mouse pad, I have a very smooth desktop. But I just tried to use a sheet of A4 printing paper, but no result, the problem persisted.
Someone on this forum suggested, that USB3 may interfere with the magic mouse.
I have 2 LaCie HDD's about 70 cm away from the mouse, I use them on Thunderbolt. But in operation or not - the result is the same, the mouse plays up! Just now I was clicking the desktop and the mouse created a new folder!!
Thanks for the advice, Bee
Cheers, Gerd

Hi. I just downloaded "angry birds" from the iTunes store. It says it was successfully downloaded and that I can use it on the two mac products I have. I can see an icon for it in the finder on the mac, but I can't figure out how to play the game. Anyone?

Hi. I just downloaded "angry birds" from the iTunes store. It says it was successfully downloaded and that I can use it on the two mac products I have. I can see an icon for it in the finder on the mac, but I can't figure out how to play the game. Anyone?

Thank you for your reply. After a lot of fruitless searches, I hit on a page that offered the same wisdom you did. I feel like rather a fool for not knowing that. Grr. I really appreciate your answer, and that you didn't end it with "dummy." Cheers to you. Hope someone does something kind for you today.

Macbook: How do I uninstall a game on the macbook? I need to reinstall the game for it to work, but I can't figure out how to uninstall the game to begin with.

I need to reinstall the game for it to work, but I can't figure out how to uninstall the game to begin with. I know that in Windows, there is an "Uninstall" option, but I have found no such option on the Macbook.

This is one OS X's few weak spots. For most software, it is sufficient to drag the application out of the Applications folder and into the trash. Of course, this does not delete its preference files, etc, but these are usually pretty small, and can either be left in place or deleted separately.
Some software might ship with a separate uninstaller utility that you can run. Sometimes, the package installer can also perform uninstalling, too.
You can buy general purpose uninstaller utilities, but as far as I know they won't work for software already installed; only for software installed once the uninstaller is in place.
Perhaps the safest option is to contact the company that made the game and ask them how it should be uninstalled.
Bob

How to play facebook game such as cityville in ipad, because it asking for flash player, but cannot download it for ipad

How To Play facebook games in iPad Safari?
Safari is asking for flash player to play it.
But i can't install it to iPad.
Or may be i must upgrade the version of safari for iPad?
or may be there some special application that can play facebook game
Thanks 4 ur help

Safari on the iPad does not support Flash and will not for the forseeable future.
Some of the FaceBook games have their own apps in the App Store that you can download.Some are the full games and some are not. For example "Cityville Hero" tells you when certain things happen in game so you can pop online on a computer and check it there, rather than letting you play it first.
Checking the App Store is the best place to find a way around using a site that requires a flash player. A lot of sites create apps so you can use them on the iPad/iPhone/iPod touch. And if you find a site that doesn't you can always contact the website creators to see if they have or will create an app for the iOS devices.

How Does EAX For Games W

Similar Messages

Maybe you are looking for