How does my Iphone and Nike + work?

Hi there,
i'm using for a week the Nike+ sensor, but i've asked myself how does they communicate and i doesn't know.
Maybe you know the answer, please let me know?

http://manuals.info.apple.com/en_US/Nike_Plus_iPod_User_Guide.pdf

Similar Messages

How does the iphone's accelerometera works?

how does the accelometer still working even when the iphone is shut down?
when I start the iphone after complete shut down and hold it in front of my face of knows what angle is this. how? accelerometer measure movement...

unless the iphone have another battery that keep measure the iphone movement even when it shut down, and then when I start the IPhone again it's know what he's position.
The iPhone does not remember its position. When it's turned on, the accelerometer detects the force of gravity, so can calculate how much the phone is tilted. This tilt reading, combined with the magnetic compass reading, can determine the phones orientation. The GPS can give the phone's location. None of this requires knowing anything that happened to the phone while power was off.
This is unlike an inertial guidance system, which has to continuously monitor rotation and acceleration to calculate how far it has moved from a starting position. An inertial system, would use too much power, and be too large and expensive, for a hand-held device. They are used for systems that have to work without outside signals, such as radio beacons or GPS. Inertial guidance systems are used on submarines, for some underground position measurements (such as mining and oil well drilling), and for plane and missile systems that have to work when GPS may be unreliable due to jamming or satellite destruction.

How does systemd, wpa_supplicant, and dhcpcd work together? rtl8188su

I'm running arch with alarm (done a pacman -Syu to get latest everything) on an original Raspberry Pi model B.
I'm using a Belkin USB adapter which is really a Realtek rtl8188su chip, which is recognized with the r8712u module. I want to do it all from the command line (not running a GUI, as this Pi won't be having a display attached.)
The system recognizes the built-in Ethernet, and dhcpcd assigns it an IP address, so I can SSH into it and try to bring up the wlan0 interface.
I'm an old-school Linux/UNIX hacker, but I haven't had a lot of experience with systemd, nor with wpa_supplicant or even much of udev, so I'm a bit lost in trying to make this work.
I made sure wpa_supplicant and wpa_cli were installed. Then I edited /etc/wpa_supplicant/wpa_supplicant.conf to add my ssid/passphrase, and saved it as /etc/wpa_supplicant/wpa_supplicant.wlan0.conf. I also did "systemctl enable wpa_supplicant," and I've rebooted.
The status of the system is that it does not enable the wlan0 interface. Further, the wpa_cli tool does not work. If I run just "wpa_cli" or with a command like "wpa_cli list" then I get the error:
could not connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
This is weird, because wpa_supplicant is running in dbus listen mode:
[root@alarmpi ~]# ps alx | grep [w]pa
0 0 94 1 20 0 5636 1416 poll_s Ss ? 0:00 /usr/sbin//wpa_supplicant -u
Each time I boot, I get this message in /dev/log/messages.log:
Nov 10 01:40:06 alarmpi kernel: [ 648.082619] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Now, if I insted does "systemctp stop wpa_supplicant" and start it manually, it does bring up the interface:
[root@alarmpi ~]# wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.wlan0.conf
wlan0: Trying to associate with a0:21:b7:63:a1:98 (SSID='jwatte' freq=2462 MHz)
wlan0: Associated with a0:21:b7:63:a1:98
wlan0: WPA: Key negotiation completed with a0:21:b7:63:a1:98 [PTK=CCMP GTK=CCMP]
wlan0: CTRL-EVENT-CONNECTED - Connection to a0:21:b7:63:a1:98 completed (auth) [id=0 id_str=]
[root@alarmpi ~]# ifconfig wlan0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet6 fe80::a86:3bff:feb4:c21a prefixlen 64 scopeid 0x20<link>
ether 08:86:3b:b4:c2:1a txqueuelen 1000 (Ethernet)
RX packets 30 bytes 3813 (3.7 KiB)
RX errors 0 dropped 1 overruns 0 frame 0
TX packets 5 bytes 610 (610.0 B)
TX errors 0 dropped 1 overruns 0 carrier 0 collisions 0
[root@alarmpi ~]#
However, dhcpcd is not auto-launched to provide an IP address to the interface.
So, how is this supposed to work? How am I supposed to configure the system so that all the pieces click together? It should start wpa_supplicant with the right config data, and/or configure it over dbus correctly, and it should make sure dhcpcd is then invoked to obtain an IP address. I have *no idea* how to actually configure this to do the right thing, because all the tutorials and documentation I can find on the web is either very abstract ("services live in /usr/lib/systemd/...") or just claim that things "will magically work" if I have the correct configuration.
Help! Don't know what to do next!

Your manual wpa_supplicant invocation result looks good, so the major hurdle you have taken already.
For wireless you need a management method that acts as interface to wpa_supplicant and dhcp and watches the connection. Before you browse off to archlinuxarm, also read the non-abstract introduction here: https://wiki.archlinux.org/index.php/Wi … management

How does Illustrator allign and distribute work

Hi
I am trying to understand what is happening behind the align and distribute functions in Illustrator.
I am working on a PC with Illustrator CS5
I have taken a photograph of a stone wall in to Photoshop:
Converted it to grey scale
Reduced it with levels to black and white
Then selected the black and converted the selection to paths.
Exported the path as an illustrator
Imported it to Illustrator ( I know I could trace it in illustrator but I prefer t work this way round).
All objects are un grouped and on one layer in Illustrator.
Select all objects
Open the Align pallet
Set Align To Artboard
Apply distribute Horizontal Center
Apply Distribute Vertical Center
The objects are distributed across the Artboard
Select all objects
Horizontal Align Center
Vertical Align Center
Apply distribute Horizontal Center
Apply Distribute Vertical Center
The arrangement is different
Do the same exercise with 15 circles of the same size and a similar redistribution happens.
What is determining or influencing the re ordering?
it does not seem to be size or the layer order.

Thanks to everyone who has replied to my question.
Some interesting information and comments.
I am still unsure as to what logic Illustrator is using. I can understand that layer or other orders might effect the order. I started thinking about creation order and if this is different to layer order. So I exported my dots test file as .svg so I could look at this. I then re imported it at the distribution was more predictable. If I align to bottom, left then distribute h and v I got a diagonal line of dots. This is what I would have expected to get. I still need to test this out more.
before svg
after svg conversion
My main problem is that if I am going to use the distribute I need to know and understand what it is doing.

How does PSE 11 and iPhoto work together?

I am currently trialling PSE 11. I would prefer to keep iPhoto as my organiser while using PSE 11 as my editor. However, it appears that I have to create a separate PSE library meaning that the edits made in PSE will not be reflected in the iPhoto library.
Other than manually importing and exporting photos between the libraries is there a way round this?

You can change iPhoto prefs to show the PSE Editor application as the external editor. You will the get the choice when right-clicking on a thumbnail in the iPhoto Library - either Edit in iPhoto or Edit in External Editor.
The export copy will be created automatically and will show up in the iPhoto Library as a duplicate next to the original once you save in PSE after you finish editing. If you don’t want duplicates and are happy to replace (overwrite) your originals you can set up the PSE prefs to automatically save over original.
See attached link for further information.
http://helpx.adobe.com/photoshop-elements/kb/photoshop-elements-iphoto-mac-os.html

How well does the iPhone 5s/5c work with Wind Mobile?

I'm going to be (hopefully) getting the iphone 5s or 5c soon and I'm trying to decide on which carrier to go with. How well does the iphone 5s/5c work with wind mobile and how fast is the internet with data?

http://www.windmobile.ca/
iPhone: Wireless carrier support and features

I live in the country and there is no High speed available, How does Firefox for desk top work with Dial up ???

I live in the country and there is no High speed available, How does Firefox for desk top work with Dial up ??? I have a great dell computer, Dimention 8400. Before I install firefox I want to know for no waste of time for either party..

Unless you enabled Find My iPad on it before it was stolen then there isn't any way to locate it. If you did enable it then you could try locating it either via http://icloud.com on a computer or Find My iPhone on another device - but that will only work if it's connected to a network and the device hasn't already been wiped and/or Find My iPad disabled on it.
If it was stolen then you should report it to the police. You should also change your iTunes account password, your email account passwords, and any passwords that you'd stored on websites/emails/notes etc.
If it was never registered to your account then it won't appear on your support profile : https://supportprofile.apple.com/
The only other ways to find it that I know of (apart from on the actual device) are via the packaging, the backup on a computer's iTunes : http://support.apple.com/kb/HT4061

How does the shake to shuffle work on ipod touch 4g?

So, i want to know how does the shake to shuffle work, i opened the music player and started playing a song but when i shake the ipod, nothing happens, the option of shuffle on the screen is still white and when the song currently playing ends, the next one in alphabetical order starts. The shake to shuffle option in settings is On.

The iPod can only tether via Bluetooth for internet connectivity to an iPhone. It will connect to other phones to tether for internet connectivity if the phones can act like a wifi hotspot.

How does Creative Cloud for teams work with staff who work in two locations ie in the office/home

How does Creative Cloud from teams work with staff who work in two locations i.e. in the office and home?

There is no difference please be aware that each login is provided with two activations however. If you wish to have a computer at both work and home activated though that is perfectly fine as long as your employer is ok with using company software at home.

How does the DAQmx read.vi work in producer/consumer mode

Dear all,
I have one question: how does the DAQmx read.vi work in producer/consumer mode ?
I mean if i set the acquisition samples quantity is 5000,(see the enclosed picture), how does the DAQmx read.vi acquire the samples ?
5000 samples one time ?
And how does the write. vi work ? Also 5000 samples one time ?
Look forward to your reply.
Thank you.
Attachments:
producer consumer mode.png ‏28 KB

It will read 5000 samples per channel.
The Write Measurement File just writes whatever you give it. It you send it 5000 data points, it will write the 5000 data points.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

How does the Mac App Store work?!

Hey guys i recently posted this quesiton in a different area of the community but instead of being helped was just ridiculed for posting in the wrong place... +1 for helpfulness guys :/ lol Anyways... ive been told to ask in the development section.. I have a $9.99 app and it was sitting at 10th place in the top grossing apps a few weeks ago on the UK app store, now I noticed in the morning that it was ahead of an app which was 49.99 so i presumed that I must have sold at least 5 or 6 to be ahead of him (my idea of top grossing is quantity x price) but when itunesconnect released their reports in the afternoon it turned out that i'd only sold 1 copy.. so what im asking is basically how does the top grossing section work? and how regularly does it update? is it live? daily? etc
Thanks in advance!

Your rank is better than the other app because you've made a sale while they've made none. When you make a sale, you jump in the charts, and after that you slowly go down if you don't make another sale. In other words, the bottom of the charts has many apps that didn't make any sale recently. I've also noticed that if you make some sales in other countries than the current chart, that'll very slightly improve your rank.

How does the Iphone go offline so often?

How does the Iphone go offline so often?

My son has an iPod 5 and it goes offline as soon as it locks (this occurs under both IOS 6 and IOS 6.1). This renders the "Find my iPod/iPhone" useless. How can I keep the iPod online?

My iPod has not been working for a month now and i was hoping that you could help me.The part where you charge and sync the iPod is not connecting.There is defiantly not the lead as we use it for the iPhone and that works please could you help!

my iPod has not been working for a month now and i was hoping that you could help me.The part where you charge and sync the iPod is not connecting.There is defiantly not the lead as we use it for the iPhone and that works please could you help!
yours sincerly
jackfromsurrey

What I am saying is ..........
The iPhone HAS to be active making calls on the UK carrier network for the carrier to identify as "theirs" and therefore eligible for the Carrier to unlock
The way to achieve this is to use a PAYG sim making and receiving calls to establish a customer relationship with the Carrier and then follow the Carrier's process to unlock
With a PAYG it usually means adding a specified (by the carrier ) amount usually £15 /£20 depending on the carrier
This is how O2 function and according to Gemma this is how Vodafone work

How does EXIT modules in DMEE work?

Dear friends, how does EXIT modules in DMEE work?
If I want to use this module DMEE_EXIT_DK_OCR_ACCOUNTNO to extract the account number of an OCR line, what should I do?
And especially what do I put in the import parameters?
/René

The module called DMEE_EXIT_DK_OCR_ACCOUNTNO is a dummy module or template module if you like.
The problem is that the module DMEE_EXIT_DK_OCR_ACCOUNTNO has a condition that never where fulfilled!
I copied the module to Z_DMEE_EXIT_DK_OCR_ACCOUNTNO and changed the conditions u2013 and then everything was working with import and export parameters!
Either is DMEE_EXIT_DK_OCR_ACCOUNTNO a serious mistake in standard SAP or just an undocumented template to be modified!
/René

How does the widgets HTML snippet work on iweb?

How does the widgets HTML nippet work on Iweb? and when should you use it?

Joe R wrote:
I'm creating Tool Tip definitions for the Operators in the Filter on the Interactive Reports. I was looking for a definition for the 'Contains' operator and from what I've found this operator is used to do a text search and it returns a relevance score for every row selected.The IR "Contains" filter is not the same as the Oracle Text <tt>contains</tt> operator.
The IR "Contains" filter performs a simple string comparison on all of the column values returned. It does not make use of any Oracle Text indexes on the underlying data.
Despite < a href="https://forums.oracle.com/forums/thread.jspa?messageID=2434666">vague promises of enhancement</a>, no Oracle Text support has yet been included in Interactive Reports.

How does my Iphone and Nike + work?

Similar Messages

Maybe you are looking for