How good is the baseline imac at running games?

Will it run Battlefield 2 or Call or duty pretty well?

Here are system requirements for COD Mod Warfare from Apple App Store:
Here are the specs for the cheapest new iMac:
Other than the card not being specifically mentioned it should be fine. You can email COD to ask if you want to be sure.

Similar Messages

How good is the latest iMac 21.5inch 500gb

How good is the latest iMac 21.5inch 500gb

That is very subjective. Better than what I'm using and it works fine for what I do.

How to measure the baseline of a noisy, pulsed signal

Hi
I am measuring the torque exerted by a large motor on a shaft using a load cell and lever arm. The shaft runs at approx 150 rpm. I have attached a drawing that shows the output I get. This is a test rig.
I have written some code that measures the maximum peak out of a group of approx 5 peaks and writes this to a shift register. This gives me an idea of the maximum torque "spike".
I also wish to measure the baseline torque (due to the bearings in the machine). Even when highly filtered (my noise filter is set to 49Hz) the signal exhibits this noise which is probably due to vibration in the system. The signal is zeroed when the motor is not running.
Does anyone have an ideas on how to measure the "baseline" torque? The large spike in torque prevents me from doing a running average. Can anyone think of a way of averaging just the noisy part of the signal to get an average value? I aim to to subtract the average baseline torque from the peak value to get an idea of the torque due to the event which causes
the spike.
Any help would be greatly appreciated.
Many thanks.
Attachments:
drawing of torque signal.gif ‏26 KB

Thanks for the reply. I understand what you are saying. However, I might have to modify my method for measuring the peaks if I choose to implement your idea. I have taken a screenshot of my "peak finder" code and attached it.
Bascially, the reset terminal is wired to a timer which outputs a pulse every few seconds. This resets the vi (a standard NI one I think) and sets the peak magnitude back to zero. This way, I am windowing the signal and measuring the maximum peak in every window. This is what I need to do.
So I could use a logical filter to feed data to the running average only if;
the amplitude of the signal is less than a certain threshold
and if the current value has similar low peaks either side of it
How would you construct the code to delay the evaluation so that the values in front and behind of the current data point can be analysed?
thanks again
Attachments:
peak_find_screenshot.jpg ‏45 KB

How good is the 3G arial on the iPad?

How good is the 3G arial on the iPad? For example is it better than the iPhone 4 one?

I'm using the IGP on 2 networked pc's and to be honest have had no problems with it. Runs all my games at ease inc the network games, (some are very power hungry too). Ok not as fast as the latest all singing cards but costs you nothing. You can always stick another card in if you get problems. One thing though, gotta make sure you make use of the Dual channel memory, this really speeds things up with the IGP in use.

How good is the Stock Cooler

Hi ppl.
As u prob know I am building a PC for my friend. It will be a AMD 64 3200
My question is if I bought the retails then how good is the cooler? Also will it come with a Thermal Pad
If I bought the retail could I scrap off the Pad and used Thermal Paste Supplied with my Zalman 7000Al/Cu as this isnt silver based. Would this boid the warrenty.
Or I would buy the OEM version and get a Thermaltake Silent Boost along with Artic Silver 3.
Wot would u guys do because u get a warrenty with the one and not with the other. I think the Silent Boost would be a much better option for cooling.
My friend will be doin now otherclocking but wants a stable cool running system without being very loud (so no TORNADOS lol)
Cheers
SAspaz

Quote
Originally posted by RLiu818
Quote
Originally posted by skank
The stock cooling is very adequate if you are not overclocking, enable cool and quiet and it will be pretty silent when not under load as well. The thermal pad it comes with is fine too. I used the stock cooler before I got my new mobo and HSF, kept my A64 at 38 deg idle, 43 deg under load. Perfectly fine temps.
what does cool n quiet do exactly?
i enabled it in my BIOS and i dont notice any difference,
i have a SLK948U with a Panaflo L 80mm
You need to have your fan plugged into the motherboard CPU fan header for it to reduce fan speed, I guess you don't with that fan as it draws too much current.
Oh and even if you are going to Overclock you will find the stock cooler is actually fine for mild overclocks of a couple of hundred mhz, I tried it with my Clawhammer and got it to 2200 mhz with 41 deg idle and 48 deg under load, temps that are fine in my opinion.

How good are the WD MyBook Studio Ed. Refurbished Replacements?

I have a Western Digital MyBook Studio Edition for Mac - External Hard Drive that is 2 years old, and has started to have problems.
It keeps running constantly and gets very warm. I unplug the cables from it, let it cool for a few minutes, replug the cables, and do a forced backup.... but the next scheduled backup, it starts up and will keep running for hours without doing the backup.
So I unplug it again, let it rest, replug, then do a forced backup, and everything repeats itself as previously mentioned.
I called WD Support this morning, and she said that I could send it in, and they would send me a refurbished replacement. I have read on other forums (tools, etc.) that people send items in for a replacement, and they get back a refurbished unit that is all banged up, and doesn't work properly.
My question is... how good is the WD refurbished replacements that they send back. Are they in good condition? Does anyone have any experience with WD on this?
I have even thought of just getting a new external HD from another company, (G-Drive, LaCie, etc), but I have seen mixed reviews on them. I like the G-Drive Solid State (no moving parts) but that is over $500.... too rich for my blood.
Any recommendations on either question.
Thanks,
Jim

From what I've read on the internet WD offer poor customer service and their products are of low quality. Certainly I have experienced first-hand many WD hard drives failing, mostly with the dreaded click click click. I've only known two or three Seagates go this way in all the years I've been using hard drives (pretty much since the early days of 120MB).
It may be expensive, but I highly recommend the ReadyNAS Duo as a backup solution and / or as general network storage. I have one set up with two 1TB Seagate NS drives in mirrored mode and it works very well. Seagate NS drives are enterprise-standard, designed for use in RAID hardware where they will be in close proximity to one another, Seagate AS drives are not designed for this purpose and so may fail in this situation. Other hard drive manufacturers make enterprise-grade drives too, I'm guessing that the ones WD use in their MyBook products are not these drives though which might explain why there are so many failures. The enterprise-grade drives typically cost about £20 more but I think for reliable backup purposes it's well worth the extra expense.

How to call the Application configuration in run time.

hi guru,
i have created two Application configuraton and it working fine.
my question how to call the application configuration in run time.
Example :
Based on the user i want to change the Application Configuration.like Super user and Normal user.
Advance thank's
Regard's
Vivekanathan.S

Hi,
Please try out this way-
Have a look at this table -
WDY_CONF_APPLU - (Customizing Data for Web Dynpro Applications).
after you are done with the configuration--
Ge the config id for the given application from this table. And depending on the user get an entry from this table and display accordingly.
Please refer to these links -
different default layouts for different CONFIG_IDs
Get WDCONFIGURATIONID
Regards
Lekha

How good is the audio jack?

In the past I've connected my iPod to my stereo using a mini to RCA adapter. It gave me a weak signal (even with the volume turned all the way up). How good is the Mac Mini's audio when plugging into a stereo? Thanks.

Optical out to a DAC supports 24-bit (and even 32-bit on the new mini, whatever that is for, I guess DSP). It shares the analogue headphone jack out, but when you put a mini Toslink in it, you get the light out.
You can also use USB out or use a USB/coax converter (which I am messing around with). Others have told me that the USB/coax converter is better because it externally clocks the signal, but I cannot hear any difference between that and the optical out. Optical goes up to 96kHz sampling frequency. To get higher, you need the USB/coax adapter.
The NOVA that I have, linked to above, supports 16-bit output from USB and 24-bit output from optical toslink and coax. I think the USB limitation might be imposed by the software in the DAC, however, not at the mac end.

How good is the iPod Touch Upgrade?

How good is the iPod touch upgrade? is it really worth it? should i upgrade? or should i wait for the sdk to come out and then upgrade?
And are there any safety/security features for safari? to protect your ipod touch from hacks and viruses?

There were some Mac viruses in the past (like 10 years ago), but none for OS X.
Sophos provides a list of Mac viruses here. Almost all are from the late 1980's and early 1990's. The most recent one being June 1998 - and all of them affecting Mac OS 7, 8 or 9 - none for Mac OS X
Virus software on the Mac mainly detects and protects against passing on Windows viruses, which do nothing on a Mac.
In fact, Virus protection software on the Mac is a bit of a scam, as there's none to protect against.
A couple of 'proof-of-concept' viruses were demonstrated for OS X but never released, and as I said, there's not a single virus in the wild that affects current shipping versions of OS X.
Not a single one.

How to Hide the Parameter field at run time....

Hi,
I have a parameter field which behaves differently depending on the User logged in.
It has the LOV coming from following SQL.
SELECT customer_name FROM Cust_mast;
If the user = 'INTERNAL' then the Where clause will be
WHERE cust_id in('DELL', 'SBC', 'BANK')
Else there will be no WHERE clause or the parameter field
should be hidden in the parameter form.
So my questions are:
1) How to hide the Parameter field during Run time?
OR OR OR
2) How to change the LOV select statement during Run time?
Thanks.
Ram.

Hi Ram,
Is there any way to play with the sql query SELECT using DECODE ?I'm not sure of this part, maybe someone else can suggest a way.
However, what you want can be done in 2 other ways:
1. Build 2 reports. Both reports will just be duplicates of each other, only difference being that the 'LoV where clause' will be different. Now you can fire the appropriate report in many ways. For example, if the customer is alreay logged inside your custom application, and therefore you already know whether the user is internal of external, you can design your button or link which launches the report to contain logic such that one of the 2 reports is fired depending on who the user is.
1. Use a JSP parameter form, not a paper parameter form In this case, just build an HTML parameter form in the web source of your report. Use Java logic to populate the LoV drop-down list. When you have to launch the final report, just launch the paper-layout of the report. For example (you will have to modify this):
<form action="http://machine:port/reports/rwservlet?report=ParamForm.jsp+..." name="First" method="post">
<select name="selected_customer" onChange="First.submit()" >
<option value="">Choose a Customer Name
<rw:foreach id="G_cust_id" src="G_cust_id">
<rw:getValue id="myCustId" src="CUSTOMER_ID"/>
<rw:getValue id="myCustName" src="CUSTOMER_NAME"/>
<option value="<%=myCustId%>"><%=myCustName%>
</rw:foreach>
</select>
</form>
In the code above, you will have to make sure that your report's data model defines 2 CUSTOMER_ID's (like CUSTOMER_ID_INT and CUSTOMER_ID_EXT). These 2 will be internal and external Cust ID's. Use Java logic to show one of them.
Navneet.

How to hide the Parameter field during Run time?

Hi,
How to hide the Parameter field during Run time?
I have a parameter field which behaves differently depending on the User logged in.
I am using reports 10G
For ex: I have 3 field created in JSP
CUSTOMER
PROVIDER
FROM DATE
END DATE
If the user = 'SUPER show all the parameter
CUSTOMER
PROVIDER
FROM DATE
END DATE
If the user is 'GATEKEEPER" Just show
PROVIDER
FROM DATE
END DATE
Can I do that?
Please help
Thanks.
KK

hi, i'm not familiar much with JSP. but i think workaround is to create two window one which have 4 fields and the other which have 3. if user is SUPER then call the first screen otherwise if user is GATEKEEPER then call the second screen.

The baseline iMac or the 1 499$ iMac?

Hi,
I have used windows all my life, and I'm pretty tired of it. So, I want to switch to Apple and buy an iMac, but which one should I buy? The baseline iMac or the 1 499$ iMac?
The 27" iMac is a bit too big for my room/ desk, and i don't feel the need of 27". So will the two baseline iMacs edit hd videos in Final Cut Pro X, After Effects CS 5.5, Premiere Pro CS 5.5 etc., without problems?
Thanks in advance!

baltwo wrote:
I'm confused. The cheapest iMac is $1,199.00. You'll need to wait for mavens who do video stuff for their recommendations. To get you started, see these:
Switching from Windows to Mac OS X,
Basic Tutorials on using a Mac,
Mac 101: Mac Essentials,
Mac OS X keyboard shortcuts,
Anatomy of a Mac,
MacTips,
Switching to Mac Superguide, and
Switching to the Mac: The Missing Manual,
Snow Leopard Edition.&
Additionally, *Texas Mac Man* recommends:
Quick Assist,
Welcome to the Switch To A Mac Guides,
Take Control E-books, and
A guide for switching to a Mac.
Yeah, the baseline iMac (aka. the $1,199.00 iMac) or the $1,499.00 iMac? (Mainly for video editing)

How to find the SQL Server Instances running across the given activer directory domain?

How to find the SQL Server Instances running across the given activer directory domain?
I have though of OSQL -L , Microsoft Assessment and Planning ( MAP ) tool and SQLPing3 (SQLSecurity) might help me.
I would appreciate if there any other way of finding the SQL Servers / Instances running across the given active directory domain.
Sivaprasad S
http://sivasql.blogspot.com
Please click the Mark as Answer button if a post solves your problem!

Dear ,
Very simple u find all instances through the customized sp which is get all details about inventory. Like i put the sp bellow. This is without any tool.
USE [master]
GO
/****** Object: StoredProcedure [dbo].[DBStatus] Script Date: 08-01-2015 19:46:11 By Damodar Patle Sr. DBA Mumbai India ******/
SET ANSI_NULLS ON
GO
SET QUOTED_IDENTIFIER ON
GO
ALTER PROCEDURE [dbo].[DBStatus]
AS
SELECT
SERVERPROPERTY('servername') AS ServerName,
ConnectionProperty('local_net_address') AS 'local_net_address',
ConnectionProperty('local_tcp_port') AS 'local_tcp_port',
CONVERT(VARCHAR(25), @@VERSION) as VERSIONSQL,
SERVERPROPERTY('ErrorLogFileName') AS ErrorLogFilePath,
database_id,
CONVERT(VARCHAR(25), DB.name) AS DBName,
CONVERT(VARCHAR(10), DATABASEPROPERTYEX(name, 'status')) AS [Status],
CONVERT(VARCHAR(10), DATABASEPROPERTYEX(name, 'Recovery')) AS [Recovery_Model],
create_date as DBCreate_Date, --physical_device_name,
(SELECT COUNT(1) FROM sys.master_files WHERE DB_NAME(database_id) = DB.name AND type_desc = 'rows') AS DataFiles,
(SELECT SUM((size*8)/1024) FROM sys.master_files WHERE DB_NAME(database_id) = DB.name AND type_desc = 'rows') AS [Data MB],
(SELECT COUNT(1) FROM sys.master_files WHERE DB_NAME(database_id) = DB.name AND type_desc = 'log') AS LogFiles,
(SELECT SUM((size*8)/1024) FROM sys.master_files WHERE DB_NAME(database_id) = DB.name AND type_desc = 'log') AS [Log MB],
(SELECT physical_name FROM sys.master_files WHERE DB_NAME(database_id) = DB.name AND type_desc = 'rows') AS MDF_File_Location,
(SELECT physical_name FROM sys.master_files WHERE DB_NAME(database_id) = DB.name AND type_desc = 'log') AS LDF_File_Location,
user_access_desc
FROM sys.databases DB
ORDER BY dbName, [Log MB] DESC, NAME

How good is the Airport Express inbuilt Digital to Analogue converter?

How good is the Airport Express inbuilt Digital to Analogue converter?
I have just purchased a 2012 dual band Airport Express which has the combined optical/3.5mm analogue jack audio output.
This is to connect to my hifi seperate amplifier, which does not have an optical input.
This gives me a couple of options
a) just use a standard 3.5mm jack to phono cable (and use the built in DAC in the airpor express)
or
b) purchase a seperate DAC to convert the optical from the Express into phono and connect that to the amplifier
I will be sending 250-320kbps music to the airport express wirelessly.
Will I see much/any benefit in sound quality with option B vs option A?
I ask because option A is free (I already have the cable) and option B will be around £20-£30 depending on which DAC I were to buy (I would also need a new TOSlink optical cable).
These are the sort of DACs I was looking at.
Thanks, Chipstix

How good is the Airport Express inbuilt Digital to Analogue converter?
Please check out this stereophile article on the earlier AirPort Express. I understand that the newest version may use basically similar audio hardware.
I will be sending 250-320kbps music to the airport express wirelessly.
The AirPort Express Base Station (AX) works only with iTunes v4.6+ and is limited to music files that iTunes can read; ie, 16-bit data only. (An exception is you can use a third-party product like Rogue Amoeba's AirFoil to stream other non-iTunes sources.) These data, though, can be in any file format that iTunes recognizes, from lossy MP3s at the low-quality end of the spectrum to Apple Lossless and lossless AIF or WAV files at the high end. It is also important to note that the AX functions only at a 44.1kHz sample rate. When you play 32kHz or 48kHz data, iTunes sample-rate-converts the data in real time before sending it to the AX.
iTunes uses a QuickTime CODEC to convert audio files to Apple Lossless, and then, uses AirPlay to send them to the AX. In turn, the AX uses built-in software that converts the Apple Lossless to an Encoded Digital Audio format. From there, digital audio is sent to a optical transceiver to convert the electrical signal to an optical one before sending it to the innermost part of the audio port. As you already know for analog, the AX has a built-in DAC to convert the Encoded Digital Audio to Analog which is sent to the same audio port.
One operational glitch is the fact that, as the AX doesn't have a local clock circuit, when the incoming data is interrupted, as it is when you change songs in iTunes, there is no longer a digital output to feed the DAC, which loses lock as a result. Using an external DAC, which may offer better audio performance, may have issues with this glitch. Some DACs are more sensitive than others.

How to delete the saved score in a game downloaded from app store for my macbook and restart the game from the beginning ? please help

HOW to delete the saved score in a game downloaded from the app store to restart the game from the begining with fresh scores.
i am unable to do so. please help

In system preferences, create a new account again, using the short name of the "deleted" account. You may be prompted to re-use the old home folder. Log out and log in to test it worked. Then log in as your new admin, and do the delete process again. Don't choose to securely delete this time - just a regular delete.
When you have time to spare, go to Disk Utility, and use the Erase tab to securely erase free space on the drive. This will accomplish the same thing that your originally tried to do. Use the fastest method - anything more secure is a waste of time. You may need to run it overnight - it can take several hours.
Matt

How good is the baseline imac at running games?

Similar Messages

Maybe you are looking for