How I can extend JSlider to work with non-integer values?

I need to create slider with non-integer scale. How I can do it?

As it turns out, I found a solution by myself. By using the "onBlur" method instead of the "onChange" method, I got what I needed.
Thanks,
Ralph

Similar Messages

How I can stop the combo box with list of values from fireing validations

Hi I'm using Jdeveloper 11.1.2.3.0
Using Hr Schema employees table
I Display employees data in af:table
and I make List Of values on Department_id filed to easy change the employee department
and another one on Job_id filed
and Imake them UI Hints as ( combo box with list of values ) in the employeesVO
the problem is when I Select a value from department or jobs ( combo box with list of values )
fires the entire filed validations for mandatory atributes
Note : the af:table Property ( contedelivery) is set to (immediate )
How I can stop the combo box with list of values from fireing validations

check it out.,
http://andrejusb.blogspot.in/2012/09/what-to-do-when-adf-editable-table.html

Can LabView FPGA module work with non-NI FPGAs?

Simple Question: Can the LabView FPGA Module work with other FPGAs? Im assuming yes, but id like ot make sure first. Normaly I go with NI for most of my stuff, but they just are lacking in the FPGA hardware for what I need, but Im accustumed to LabView so I would like to stick with that to program it.
Thanks!
-Mark

Using LabVIEW and LabVIEW RT you can access the registers on any PCI/PXI card using the NI-VISA driver. NI-VISA also allows you to handle interrupts and DMA data. For interrupts you will not actually write an interrupt service routine (ISR) in LabVIEW. Instead the VISA driver will acknowledge the interrupt to the card and then pass a VISA event to the LabVIEW application letting the application know that it needs to process the interrupt. Detailed information about this type of programming is available in the following documents.
Using the VISA Driver Development Wizard and NI-VISA to Register-Level Program a PXI/PCI Device unde...
Configuring LabVIEW Real-Time and NI-VISA to Recognize a Third Party Device
Configuring LabVIEW Real...
Developing a LabVIEW Real-Time Driver for a PXI or Compact PCI Device
Porting a Windows PCI Device Driver to LabVIEW Real-Time
Considerations in Implementing LabVIEW Real-Time Drivers
Christian L
Christian Loew, CLA
Principal Systems Engineer, National Instruments
Please tip your answer providers with kudos.
Any attached Code is provided As Is. It has not been tested or validated as a product, for use in a deployed application or system,
or for use in hazardous environments. You assume all risks for use of the Code and use of the Code is subject
to the Sample Code License Terms which can be found at: http://ni.com/samplecodelicense

How can I populate a UILabel with an Integer value?

I have a UILabel field and I want to display an integer value in this field.
I used lblTemp.text = @"number of apples"; this worked for string only. But now I have an TempInt integer whose value I want to put into the lblTemp.text.
my final label field should be "number of apples is <TempInt>"
Any suggestions on the syntax to do this?
thanks for the help,
Max

[NSString stringWithFormat:@"%d", tempInt]

Can't get extended class to work with asbstract class

I am having trouble working an extended class to work with my base abstract class. I keep getting this error message: "Fiction.java:4: invalid method declaration; return type required" public FictionBook()" Can someone give me some advice and or guidance on what I need to do? Thanks.
Here is my abstract class:
import javax.swing.*;
public abstract class Book
     protected String bookTitle;
     protected double bookPrice;
     public abstract double setPrice();
public Book()
          setBookPrice();
public double getBookPrice()
          return bookPrice;
public abstract void setBookPrice();
Here is the extended class that I have:
import javax.swing.*;
public class Fiction extends Book
     public Fiction()
          super();
          setBookPrice();
     public void setBookPrice();
          bookPrice = 24.95;
     public String toString()
          return("Fiction Book Price is $" + bookPrice);
}

Fiction.java:2: Fiction is not abstract and does not override abstract method setPrice() in BookThis one is pretty straightfoward: Book declares an abstract setPrice() method. In effect is promises "every concrete subclass of Book will define an implementation of setPrice()". But your Fiction class does not do this - it does not give an implementation of setPrice() even though as a Book it is required to do so. That is what the compiler is complaining about.
Fiction.java:6: call to super must be first statement in constructorThis one is slightly cryptic. If you use super() it must be as the first line of a constructor. You are using it as the first line of Fiction() so that looks OK - until you realise that Fiction() is not a constructor! That's because you declare it as a method returning void. Remove the "void" and the compiler will recognise it as a constructor and will be happy about your use of super().
Edited by: pbrockway2 on Sep 13, 2008 12:13 PM
Just a general point: it might be worth writing very brief comments for your abstract class to say what the methods are supposed to do. It isn't really clear what setBookPrice() is supposed to do given that it isn't passed any argument. Likewise setPrice(), how does it differ from setBookPrice()? what is the double value that it returns?

My old appleID use email with domain already deactivate. So I changed my appleID and primary email and now I can not access iCloud with iOS7. ICloud shows my old appleID but I can't change it. How do I get iCloud to work with my updated ID?

My old email that using register for apple ID cannot access/check any mail because that domain already deactivate.
So I changed my appleID and primary email and now I can not access iCloud with iOS7. ICloud shows my old appleID but I can't change it. How do I get iCloud to work with my updated ID?

Hi ccharat,
Welcome to the Apple Support Communities! It sounds like you did a good job editing your Apple ID and primary email address, but you didn’t sign out of iCloud on your iOS device before hand. What you may need to do in this situation is go back to the Apple ID website and edit your Apple ID and primary email address back to the email address that is signed in with iCloud (there is no need to verify the account after editing it back to the old account, just changing it back is enough). Once your Apple ID is back to the original account, delete the iCloud account from the iOS device and be sure to keep all info on the device when prompted. After you delete the iCloud account, go back to the website and edit your Apple ID and primary email address back to the new address. Once it is back to the account you would like, you can sign into the iCloud on the iOS device with that new account and merge all of the data when prompted. Please use the following article as a reference.
iOS 7: If you're asked for the password to your previous Apple ID when signing out of iCloud
http://support.apple.com/kb/ts5223
Change your Apple ID temporarily
If signing out and back in to iMessage or FaceTime didn't help, try these steps:
Change your Apple ID to the Apple ID you used previously. You shouldn't need to verify the email address.
Go to Settings > iCloud. Complete these steps only if the Find My [Device] setting is turned on:
Scroll down and tap Delete Account, then tap Delete to confirm.
Tap “Keep on My [Device]” or “Delete from My [Device].” In either case, your data remains in iCloud and will be updated on your device when you sign in to iCloud again.
Enter the password for your previous Apple ID.
Change your Apple ID to the new email address that you want to use. You'll need to verify the email address.
Return to Settings > iCloud and sign in with your new Apple ID.
I hope this helps,
-Joe

How can iWeb hit counter be made to work with non-Apple server?

How can IWeb hit counter be made to work with non-Apple server?

This tutorial describes how to add an alternative counter to an iWeb page: iW05 - Adding a Graphical StatCounter as an HTML Snippet to an iWeb Page
OT

How do I get fios to work with my new desktop w/ Windows Media Center

Can someone please help me I have "fios".TV and internet 1HDSTB + 1HDDVR with multi room dvr Home media mgr.how do I get fios to work with my new desktop HP Pavillion m9715f**(specs below)**w/ Windows Media Center or did I just throw away my money?
also equipted is 47" Samsung 850series 1080p 120hertz HD LCD TV + 36" Samsung 560series 1080p 60hertz HD LCD TV and 19"Samsung 950b LCD Monitor
** computer specs**
Product number NZ017AA
Introduction date 30-Jun-2009
Country/region sold in: United States,Canada
Hardware Base processor
Phenom-9650 (A) 2.3 GHz (95W) 3600 MHz HyperTransport 3.0 Socket, AM2+
Chipset AMD 780G
Motherboard Manufacturer: MSI Motherboard Name: MS-7548 HP/Compaq motherboard name: Aspen-GL8E
Power supply 300W
Memory
Component Attributes Memory Installed 8 GB Maximum allowed 16 GB (4 x 4 GB) (64-bit OS)
4 GB* (4 x 1 GB) (32-bit OS)
*Actual available memory may be less Speed supported PC2-6400 MB/sec Type 240 pin, DDR2
Hard drive750 GB SATA 3G (3.0 Gb/sec)7200 rpm
Blu-ray player & SuperMulti DVD burner with LightScribe Technology drive
This Blu-Ray Disc DVD drive introduces a player that reads Blu-ray Disc format enabling you to watch high-definition Blu-ray Disc movies. NOTE: This drive does not include high-definition write capability.
Formats/Disc types Write speeds Read speeds Storage capacity Blu-ray Disc BD-ROM SL NA up to 6X up to 25 GB BD-ROM DL NA up to 4.8X up to 50 GB BD-R SL not supported up to 6X up to 25 GB BD-R DL not supported up to 4.8X up to 50 GB BD-RE SL not supported up to 2.3X up to 25 GB BD-RE DL not supported up to 2X up to 50 GB HD DVD not supported DVD DVD-ROM SL NA up to 16X up to 4.7 GB DVD-ROM DL NA up to 8X up to 8.5 GB DVD+R SL up to 16X up to 12X up to 4.7 GB DVD+R DL up to 4X up to 8X up to 8.5 GB DVD+RW SL up to 8X up to 10X up to 4.7 GB DVD+RW DL not supported DVD-R SL up to 16X up to 12X up to 4.7 GB DVD-R DL up to 4X up to 8X up to 8.5 GB DVD-RW SL up to 6X up to 10X up to 4.7 GB DVD-RW DL not supported DVD-RAM up to 5X up to 5X up to 4.7 GB CD CDROM NA up to 40X up to 700 MB CDR up to 40X up to 40X up to 700 MB CDRW up to 24X up to 40X up to 700 MB CD-DA NA up to 32X up to 700 MB Video CD NA up to 10X up to 700 MB
Wireless Wireless LAN 802.11 b/g
Video Graphics Radeon HD4350
512 MB DDR2 memory
I/O Ports: HDMI, VGA, single-link DVI
Television Hauppauge ATSC/NTSC TV tuner card with FM tuner
Sound/Audio High Definition 8-channel audio
ALC 888S chipset
Network (LAN) Integrated 10/100/1000 Base-T networking interface
Memory card reader
Contains an Infrared receiver for remote control
Supports the following cards:
Compact Flash I
Compact Flash II
IBM Microdrive
Secure Digital (SD)
mini-SD
MultiMediaCard (MMC)
Reduced size MultiMediaCard (RS-MMC)
MultiMediaCard Plus (MMC plus)
MultiMediaCard Mobile (MMC mobile)
Memory Stick
Memory Stick Pro
Memory Stick Duo
Memory Stick Pro Duo
SmartMedia
xD Picture Card (xD = extreme digital)
External I/O ports
I/O ports on the front panel
Port type Quantity 15-in-1 (4 slot) with IR Receiver One USB Two Headphone One Microphone One Audio L-R One S-video in One Composite video in One
I/O ports on the back panel
Port type Quantity PS/2 (keyboard, mouse) Two S/PDIF out (coaxial) One VGA One (disabled due to the installation of a graphics card) DVI-D One USB Four 1394a One LAN One Audio (side speaker out, rear speaker out, center/subwoofer-out , line-in, line-out, microphone) One Each
Expansion slots
Slot type Quantity PCI Express x16 One (None available) PCI Express x1 Three (Two available)
Drive bays
Bay type Quantity 5.25" Two (One available) 3.5" Two (One available) Personal Media Drive One (One available) Pocket Media Drive One (One available)
Keyboard and mouse HP multimedia keyboard HP PS/2 optical mouse
Remote Control USB infrared remote control,Remote control expansion card with IR ports,IR emitter cable to transmit codes to a set top box

Based on what you've posted, your computer does not have the right tuner. You need a QAM tuner to record locals from FiOS, or a CableCard tuner to record all local and cable channels from FiOS.
QAM tuners to record local channels only
This requires Windows Vista or Windows 7
Hauppauge WinTV-HVR-2250
SiliconDust HDHomeRun (info on a sale)
CableCard tuner to record local and cable channels
This requires Windows 7 + one CableCard from Verizon for $3.99/mo
ATI TV Wonder Digital PC CableCard Tuner (records one channel at a time) -- $200-$250 on ebay
Ceton MOCUR tuner (records four channels at a time) -- coming in early 2010 for $400-$600
Make sure your computer has Windows 7 Home Premium (or better) installed. That's necessary to support CableCard tuners.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.

Update to kichat: FAQ 2 - How to get my router to work with iChat?

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

I upgraded to Mountain lion. I could not open any of my word documents so i downloaded Libre Office. It is downloaded but how do I get it to work with my old documents??

I upgraded to Mountain lion. I could not open any of my word documents so i downloaded Libre Office. It is downloaded but how do I get it to work with my old documents??

I don't know what file formats LibreOffice supports, but my guess is it can only handle the OpenXML format (new Office docs).
You could use this online converter: http://www.zamzar.com/convert/doc-to-docx/

How do I get iCloud to work with my mac that has snow lepard and is pre intel?

How do I get iCloud to work with my mac that has snow lepard and is pre intel?

Richard Kerns wrote:
And it kills me that a friend who has pc computers and just has an iphone and ipad can breeze through all this with no problem and he still has XP. So Apple goes back and helps old OS for pc but not for it's own kind!!!
Richard, I agree with you 1,000%. I wrote this in a forum a few weeks ago, when a user was complaining about Snow Leopard not supporting iCloud:
Why is it that if I bought a Mac before July of this year, I must pay to upgrade my operating system in order to take advantage of iCloud? Meanwhile, a Windows Vista SP2 user, who bought a new computer in May 2009, already has everything they need on their computer to use iCloud.
Why was it possible for Apple to write a free iCloud Control Panel that was compatible with existing versions of Windows, but Mac users must buy an entirely new operating system?
If Apple gave Mac users the same amount of backwards compatibility that it gives to Windows users, people with OSX 10.5 (Leopard) would be able to use iCloud. That's something to think about the next time you go to purchase a new computer.
(P.S. Something else to think about: If you bought a Mac before October 2007 (when OSX 10.5 was introduced), your computer won't run iTunes 10.5 unless you buy an upgrade. But a PC user, who purchased their computer as long ago as Sept. 2004(!), can run iTunes without an OS upgrade.)
I got so angry thinking about this, that I ended up writing an angry note to Apple on their feedback page. After repeating what I just wrote here, I asked them to commit to providing at least the same level of support to Mac users that they do for PC users when it comes to their cross platform products (iPhone, iPad, iCloud, Apple TV, Safari, iTunes, etc.) And, really, is that so much to ask?
I wish I knew how to start a petition requesting that Mac users get comparable treatment as PC users. But then again, shouldn't that go without saying?
Please leave feedback about this revolting double standard on the Apple feedback page. They should be thinking long and hard about why their own customers are treated worse than the customers of their competition.

How i can associate my app user with database role

In my application (oracle forms application developed in-house - We are using Oracle Forms 11gR2 with WebLogic 10.3.5 ), i want to use "application user" instead of database user.
I have an application users table, actually, i have database users,and of course, menu application works with database roles (It was developed with oracle forms menu module), my question is, How i can associate my application user with database role, for reusing oracle forms menu funcionality?. It's possible?
Thanks,
Edward

user8929172 wrote:
In my application (oracle forms application developed in-house - We are using Oracle Forms 11gR2 with WebLogic 10.3.5 ), i want to use "application user" instead of database user.
I have an application users table, actually, i have database users,and of course, menu application works with database roles (It was developed with oracle forms menu module), my question is, How i can associate my application user with database role, for reusing oracle forms menu funcionality?. It's possible?
Hi Edward
You can do this by assigning the role functionality to the application user. For example
create the table to enter user name.
create table to enter group name.
create table to assign user to group.
assign role to group.
assign functionality for the user by coding.
hope this helps

How to integrate Jboss seam frame work with Jdeveloper 11

hi
Really i don't know how to integrate Jboss seam frame work with JDeveloper, actually my current project implementation was started with Netbeans, but i am planning to suggest my customer , use JDeveloper.
please provide the solution are any information, how to integrate the JBoss Seam frame work.
Thanks
Lakshmi

Hi,
JDeveloper 11 does not yet provide documentation about the integration with Seam (not only the technology but also the documentation is in early preview stage). However, this is an interesting question you ask and I'll follow up to see if we can get some document out in short term.
Frank

After downloading Flash 9, how do you get it to work with Apple iMac OS X 10.3.9 ?...

a.
After downloading Flash 9, how do you get it to work with Apple iMac OS X 10.3.9 ?...
b. , c.
What's the best browser to try?... Firefox?... Opera?...
Why?...
d.
What directory/ies contain the downloaded Flash 9 files?...

a. Your browser and the flash player should work together. You should not have to do any thing
b. Camino is the best for 10.3.9 Why? You can access apples me.com through Camino on 10.3.9 but Safari will not work with me.com. Also all the internet plug ins work with camino
c. hard disk - library - internet plug ins

How to make the mobile application work with firewall and anti-virus ON

Hi,
I keep on receiving internal processing error when i try to login sap mobile solution 1.3.0 on my ipad and i was provided a solution, that is to turn off my firewall and antivirus. I works by turn off both of it but i cant possible turn of the firewall and antivirus on the server.
Can anyone guide me how to make the mobile application work with firewall and anti-virus ON
Thank you

Dear Rajesh,
Create a policy in your fire wall to allow the port to send and receive data.
I believe the port for the mobile should be port 8080 and 8443.
And your license server port 30000 and 30001
nd.Q

How I can extend JSlider to work with non-integer values?

Similar Messages

Maybe you are looking for