How is the ODD fan speed controlled?

I have a 2006 iMAC. The HD and CPU fans perform as expected, but the ODD fan 'goes like the clappers' even when the drive is not in use. I have read elsewhere the ODD uses the same sensors as the HD, is that the case? I have tried the SMC reset a couple of times but I guess this could be a hardware or firmware problem. The fans have 4 wires, I guess there is some sort of feedback system that tells the logic board the fan speed. I am an engineer, but new to MAC hardware. Any ideas chaps?
Many thanks, Andy

There is a thermal sensor on the optical drive that controls the ODD fan and either it is disconnected or there is something wrong with it.
iMac Intel 20" EMC 2105 and 2118 Optical Drive Replacement - Page 12 - iFixit
For more see > iMac Intel 20" EMC 2105 and 2118 Repair Manual - iFixit

Similar Messages

How is the gallery autoplay speed controlled?

How is the gallery autoplay speed controlled? I'm using the CADACPortfolio theme.

Hi Kernelo,
I think you are talking about changing the speed of the image slider in carousel in the cadac template. You need to make changes in the Javascript code for controlling the speed. This post has the information on it : http://forums.adobe.com/message/5060822#5060822
Please let me know if you meant something else. Also, please provide us the page URL and screenshoot as well.
Regards,
Aishvarya Raj Rastogi

[Solved] Asus L1366 mobo, cpu fan speed control

Hi, everyone,
I finally have this new core i7 system, to replace my old AMD athlonx2. I have one question about the CPU fan speed control.
I remember that in my old system, the cpu fan speed control works out of box, no configuration is needed.
But when I install arch 64 on this new i7 system, the cpu fan is running at its maximum speed constantly while the CPU temperature is modestly low. I know there is a wiki teaching how to do it.
However, I am just curious why it doens't work out of box any more? Does CPU fan control work for you guys out of box normally? especially the new Core i7 cpu users?
Please let me know, really appreciated it.
Thanks a lot.
Update: the issue is solved, see my last post, the solution is blacklisting: asus_atk0110, instead use w83667hg.
Cheers.
Last edited by mark.altern (2009-10-01 08:18:18)

First off, it would be useful to know what the sensors-detect script actually reports.
Okay. How fan control works on Linux: First, navigate to /sys/class/hwmon
Each of these folders, i.e. hwmon0, stands for a sensors monitor / fan controller on your mainboard that may control one or several fans. Inside hwmonN, there should be a subfolder called device, which contains several interfaces if your BIOS allows software-side fan control. You can read them with cat and write to them with echo.
Examples:
pwm1_enable shows if OS-level fan control is enabled (1) or disabled and in BIOS control (0). Changing fan speed won't work if this is disabled. (i.e. cat /sys/class/hwmon0/device/pwm1_enable reports 0 -> disabled; you could enable it with echo 1 > /sys/class/hwmon0/device/pwm1_enable).
pwm1 allows to change fan speed. The values range from 0 (fan off) to 255 (full speed, 12V).
fan1_input shows the current RPM if a fan is connected. You can only read from this interface. Its useful to check all of these in the each of the hwmon folders to find out if there is actually a fan connected to the fan controller (they often have more ports than mainboard manufacturers use).
There might be a fan1_div, this is somehow related to how the kernel reads the RPM, I don't know how it works.
temp1_input interfaces can appeare too, if some of the chips have temperature sensors located somewhere. I *think* lm_sensors places the core temperatures it reads from CPU (the coretemp-isa-000X thingies) in one of the hwmon-folders too.
There might be interfaces for different fans in the same hwmon folder, i.e. pwm2_enable, pwm2, fan2_input, etc., all interfaces with the same index belong to the same physical fan connector, and all in the same hwmonN are managed by the same IC on your mainboard.
Warning: These interfaces, if they work, control the fans directly without any kind of security measure. If you shut some essential fan down, it will stay off until you reboot your CPU shuts down.
(If you see something likein0_alarm, in0_input, in0_max, etc. it's a voltage monitoring chip.)
If one of those interfaces can do something, OS-level fan control does work, if none of those folders contain a working pwm interface, fan control seems to be unavailable.
Sometimes there is an option in the BIOS to enable it, and for some BIOSs software-side fan control only works if dynamic fan control is disabled in the BIOS and fan speed is set to a static value - or vice versa.
I don't know what you are using to control fan speed, there are many applications that use these interfaces, i.e. GNOME or KDE power managers, so I'm not sure what is happening:
IF: Windows 7 enables OS-level fan control and sets it the RPM to those you observed and you have nothing that provides fan control in Arch and so fan control stays at BIOS-level, which might also read out a different sensor / the same sensor differently or it might be more conservative in setting fan speeds altogether;
OR: You have something that provides fan control installed in Arch and it reads out a the wrong value supplied by lm_sensors and thus sets a higher fan speed.
Anyway, possible solutions I can think of:
Find out if you have some kind of fan control software and what it does. For example, I use the fancontrol daemon, I can't help you if you use something else.
The wiki mentions how to assign a fan speed to a certain temperature sensors. You might assign it to a different one. For example, there are no sensor chips on the mainboard of my EEE (no temp1 etc.) so I assigned the fan speed to the temperature reported by the BIOS via ACPI (those are in /sys/class/thermal, also no "device" subfolder on EEEs):
FCTEMPS=/sys/class/hwmon/hwmon0/pwm1=/sys/class/thermal/thermal_zone0/temp
You could also change the MINTEMP/MAXTEMP values to one higher than those you actually want to compensate for the effect of lm_sensors reporting temperatures that are too high.
It is currently not possible for a mortal user to change the coretemps lm_sensors reads, see this post, last paragraph.
There is a configuration file, /etc/sensors3.conf, you can change sensor names and adjust offsets here, but only for the monitoring chips and their sensors that are on the mainboard.
Last edited by Malstrond (2009-08-19 19:34:22)

Hi, the ODD fan of my computer is not working anymore. is it risky to keep on using the computer till i take it to the apple service? thanks

hi,
the ODD fan of my computer is not working anymore. is it risky to keep on using my imac till i take it to the apple service?
thanks a lot,
by the way, there is a strange "clicking sound" coming from the back of my computer. i did the AHT and it said the hardware is ok but the odd fan. the error code is 4MOT/1/40000002: ODD-0
emek cayli,
turkey

Not as bad as the HDD or CPU fan, but it still might cause a problem with the overall cooling.
What's the iStat Pro widget say about your fan speeds and temps?
iStat Pro, a Dashboard Widget by iSlayer
You also might get by for a time using smcFanControl to slightly boost up the HDD and CPU fans.
Download smcFanControl for Mac - Control Intel Mac fans to make them run cooler. MacUpdate.com
Plus you might even try kicking up that ODD fan to see if it will free up or blow out something that might be stuck in it.

Kt4a ultra fisr - fan speed controlling

hi,
does anybody know how to control the cpu fan speed when using this mainboard? i tried, as the manual says it, pc alert 4, but it did not do anything. neither does speedfan work.
is there still a chance to have success? the cpu is running @33-34°C (pc alert 4) and the fan is quite loud (5krpm).
thanks
Tristan

CompUSA is selling a very decent fan controller with digital temps read out for like 30 bucks ...It has intercahngeable face so it can match your system build ...It fits an a cd rom open slot and works and looks great ...It does work too but if the fans you have are not speed variabled then i dont care what you use it will never work ...Most CPUs and high quality fans are able to be controlled by a fan controller ...Most cheaps just spin whatever their rpm is rated to spin at ...........

Fan Speed Controll Z77

Just wondering if someone could help me, I am looking to buy a new motherboard based on the Z77 chipset (I am currently running a P67-G45), I know this is a very unusual question but does anyone know how many of the system fan headers on the Z77-GD55 and ZZ7-GD65 supports fan speed control. I am currently using a Corsair H80 with two Gentle Typhoon 1800rpm fans being speed controlled by the motherboard to 50%. Do at least 2 of the system fans support fan speed control other than the CPU fan header?

Z77A-GD65 CPU & SYS fan 1 & 2 support fan speed control (4 pin header for them) according to the manual. SYS fan 3 & 4 fan speed monitoring only. I did not check any of the other Z77 MBs. If you want to all you need to do is download the manuals and check them yourself.
http://www.msi.com/product/mb/#/?sk=Socket%201155%20%28Intel%20i3/i5/i7%29

What's the normal fan speed?

Hello, my fans have always been around 2000 rpm with both tiger and leopord, so I am wondering what is the normal range for fan speed when the computer is not running anything heavy.

So, I'm not crunching much at the moment; yet I have 133 F and 3906 rpm. However, that doesn't signify. It was flat on a wood table. Now, laptop; Room fan now on. That fan is the main thing. I read a great overview, will post link if I can find it, that air is like fluid dynamics: a MBP flat on a table in an air conditioned room (no fanned air movement) will run hotter than an MBP with space under, with a room fan, moving warmer air. Yah, no, really true.
Get freeware iStat Control 1.1 (1.2 soon): (http://www.islayer.com/), which will display fans' speed and temps in the menu bar, andmore, and make popcorn too, with the lavalamp thingee.
Then I use Fan Control, 1.2, freeware, and set it up a tiny bit just to be cool: " ... Do you think your MacBook (Pro) is running to hot? Give Fan Control a try then. Some MacBook (Pro) are just to hot for daylong use. Fan Control adjusts the minimum fan speed depending on the current CPU temperature. For safety, it leaves the original automatic fan speed control intact ..." Leopard Ready, yah.
http://www.lobotomo.com/products/FanControl/index.html
Both are preference panes in System preferences, which is very elegant, imho. And yes I have Leopard still shrinkwrapped. I will take a stab at it soon. Goodbye, cruel world (nah).

How to disable dynamic fan speed?

I have MSI 865P Neo. How to disable dynamic fan speed?

jpscwf: Personaly I always keep my fans on maximum anyway so I havn't tried saving settings at a lower level, better to have too much cooling anyway, rather than have your chip burn up..
netreaper: I may be wrong, but if your not running the corecell program then I don't think the fan speeds are adjusted. In any case, follow the instructions I gave above, and set both the fan speeds to maximum, that way you allways get the maximum cooling possible. Problem solved.

How to reduce cpu fan speed just by hardware?

Hi,
I have a K8N Neo4-F, AMD3200+ and "arctic cooling freezer 64 pro" as cpu fan. The rpm range of this fan is from 300 to 2200. I use "cool n' quiet" and "Smart CPU Fan Target with 40°C" as bios setting. When the cpu is idle ( ... just doing some typing or so on ...) it has a temperature of 32°C and the fan has ~950 RPM.
I think the fan speed is to high for this cpu load (< 5% and 1000Mhz CPU Clock). My expectation in this szenario is to have the cpu fan speed near the lower bound (300 rpm), but I don't know how to manage this (with just bios settings) ... any hints?
Thanks a lot ...

Quote from: Kwea on 12-January-06, 22:29:54
My point was you did what D.O.T. is supposed to do without using it.
Of course it's point is to auto-overclock the system to whichever degree it's set at. The problems come in because a lot of the settings it uses aren't always compatable with a lot hardware combinations. That's why it's best to come up with your own OC settings that are stable with your parts.
It's just like how the Nvidia/ATI speedup option seems like a good idea, but works poorly in practice.
Both are more useful to the marketing dept. in having more "why tech" features available to print on the outside of the retail box than they are to the end user.

Dual Core Center Fan Speed Control

Hi Everybody,
I have just bought a P35 Neo2 FR motherboard which is great but i have a question about the dual core center software.
I have installed the dual core center software and disabled 'CPU smart fan target' in the bios, but once i have set the CPU fan speed i can't save the settings as the button is greyed off.
Can anybody help me please..

Use speedfan and dump dualcorecenter !
It's infamous, lotta people having troubels with the program.
Search around on this forum and seee how many complaints there are about the program.
Including me.

Changing the default fan speeds

I have a MSI GTX 760 and I would like to change the default fan speeds. I can do this in MSI Afterburner, but this is a multi user pc and I want the fan speed to be for every user?

Hmm guess best answer is, Just dont get a msi display card. If there not going to fix a problems with fan speed's.
And MSI gaming app in OC mode makes the fan go no faster than 35%, click normal mode and go's higher.
Just use Gpu-z run test and watch the temp increase. 1 of the ways i have tested.
I feel quite let down as this is not the first time I have reported this and asked for help.
This thread just seems to be for UEFI bios.

N260GTX OC fan speed controls....

I recently finished off a build using this video card...newegg FTW! lol email offer was 185$ free shipping...SOLD!!!!!
I personally like to be able to control my parts...but I cant find any options to adjust fan speed manually....and Ntune shows it running at 26%[in motherboard adjustments]....I have never trusted auto and Id like to set it myself to 75-80% and go higher as needed....yes I push my gear hard and often and need it to stay cool...
Ntune wont do it and this is the first time Ive had an issue with NOT being able to adjust a fan using Ntune[I use it for fans and specs]....
I know it CAN be adjusted....but how?

Have you tried with Rivatuner?

MSI KT3 Ultra ARU 2 fan speed controlling

Hi, i'd like to know if is it possible to control the fan speed via software with this motherboard. I've try with Speedfan, but it seems to have no effect :( .
Suggestions?

Hi,
Sorry, it's not possible.

K9n Platinum fan speed control

Hi!
I have the following configuration:
-Motherboard: MSI K9N Platinum v1.1
-Bios: AMI v1.3
-CPU: AMD Athlon 64 X2 Dual Core)
-CPU cooler: Artic Cooling Freezer 64 Pro
-Memory: Kingmax 2*1 GB
-Video card: MSI NX7600 GT
-Power Supply: Antec NeoHE430 430W
-Hard Drive: Samsung 250 GB SP2504C
-Operating system: Win XP Pro SP2
I would like to control the speed of the CPU fan automatically, according to the temperature.
I tried
-the Dual CoreCenter utility from MSI, but it allows me only check the speed manually (If I did not miss anything)
-control from BIOS HW Monitor setting SmartFan but it does not work at all. ( Iam not sure but this can be because my cooler, it has 3 pin connector, and th MB user guide tells it works only if I use 4 pin connector. Can you confirm this?)
-Speedfan 4.31, it seemed working, but the system become instabile. I check the programmers site, and this MB did not supported.
Do you have any suggesions, experience about controlling the CPUfan?
Thank you in advance!
T.

Thank you for the answers.
Unfortunately the smartfan feature is not working in my case.( set to 3-pin in BIOS) I asked the MSI Technical Support and they said:
As this motherboard includes 4 pins connector for cpu fan, the 4th pin is used to controlled cpu fan speed, if you use 3 pins fan, fan speed will not be changed automatically and smart fan will not function.
I feel a small contradiction here
Do you have other ideas other than smartfan and speedfan?
T.

How can I adjust fan speed?

Hi; I have an HP Comaq Presario CQ57. The fan has gotten pretty loud; even when I first turn on the laptop and it is well ventalated in a cool area it is obnoxiously loud. Is there any way I can turn the fan off or adjust the fan speed? (I know it's risky so if you're going to tell me that please make sure you answer my question as well )

You can try a program called speedfan which is a free download
http://download.cnet.com/SpeedFan/3000-2094_4-10067444.html
It's a pretty hard thing to use but it does give a readout of temperatures, which is useful even if you can't use it to adjust fan speed. Also go into the BIOS (F10) and see if there is a fan always on option and if so deselect it.
The fan is running fast for a reason. It is a symptom not a disease. Very likely the computer needs to be opened up and cleaned out inside. Post back if you want some direction on how to tackle that chore.

How is the ODD fan speed controlled?

Similar Messages

Maybe you are looking for